If you are an ASTM Compass Subscriber and this document is part of your subscription, you can access it for free at ASTM Compass
    ASTM C1732 - 19

    Standard Practice for Installation of Concrete Floor Tiles

    Active Standard ASTM C1732 | Developed by Subcommittee: C15.05

    Book of Standards Volume: 04.05

      Format Pages Price  
    PDF 4 $46.00   ADD TO CART
    Hardcopy (shipping and handling) 4 $46.00   ADD TO CART
    Standard + Redline PDF Bundle 8 $54.00   ADD TO CART

    Significance and Use

    4.1 This practice is intended to provide technical information for designers, architects, and installers of CFT units in residential and light commercial construction. This practice does not address installation methods or techniques for floor tile units manufactured from other materials.

    1. Scope

    1.1 This practice covers the installation of concrete floor tile (CFT) units for application as exterior and interior flooring. Units described by this practice shall be manufactured to meet the requirements of Specification C1731. This practice is limited to the installation of CFT units.

    1.2 This practice covers aspects of installation relating to performance in service.

    1.3 Units—The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

    1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

    1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

    2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    ASTM Standards

    C270 Specification for Mortar for Unit Masonry

    C920 Specification for Elastomeric Joint Sealants

    C979/C979M Specification for Pigments for Integrally Colored Concrete

    C1232 Terminology for Masonry

    C1325 Specification for Fiber-Mat Reinforced Cementitious Backer Units

    C1384 Specification for Admixtures for Masonry Mortars

    C1714/C1714M Specification for Preblended Dry Mortar Mix for Unit Masonry

    C1731 Specification for Concrete Floor Tile

    International Concrete Repair Institute Standard

    ICRI Guideline No 310.2-1997 Selecting and Specifying Concrete Surface Preparation for Sealers, Coating, and Polymer Overlays Available from International Concrete Repair Institute 10600 West Higgins Road, Suite 607 Rosemont, IL 60018, http://www.icri.org.

    The Masonry Society Standard

    TMS 602-16 Specification for Masonry Structures Available from The Masonry Society 105 South Sunset Street, Suite Q, Longmont, CO USA 80501-6172, http://www.masonrysociety.org.

    ICS Code

    ICS Number Code 91.060.30 (Ceilings. Floors. Stairs); 91.100.30 (Concrete and concrete products); 97.150 (Non-textile floor coverings)

    UNSPSC Code

    UNSPSC Code 30131703(Concrete tiles or flagstones)

    Referencing This Standard
    Link Here
    Link to Active (This link will always route to the current Active version of the standard.)

    DOI: 10.1520/C1732-19

    Citation Format

    ASTM C1732-19, Standard Practice for Installation of Concrete Floor Tiles, ASTM International, West Conshohocken, PA, 2019, www.astm.org

    Back to Top