ASTM F1169 - 13

    Standard Consumer Safety Specification for Full-Size Baby Cribs

    Active Standard ASTM F1169 | Developed by Subcommittee: F15.18

    Book of Standards Volume: 15.11


      Format Pages Price  
    PDF 20 $48.00   ADD TO CART
    Hardcopy (shipping and handling) 20 $48.00   ADD TO CART
    Standard + Redline PDF Bundle 40 $57.60   ADD TO CART


    Abstract

    This consumer safety specification establishes the performance requirements and test procedures to determine the structural integrity, design requirements addressing entanglement on corner post extensions, and requirements for warning labels and instructional material for full-size baby cribs. Fully-furnished cribs shall be tested on, and correspondingly conform to the following test requirements: mattress support system vertical impact properties; drop and stationary side (static and cyclic) properties; crib side spindle/slat torque properties; drop and folding side latch properties; and plastic teething rail properties.

    This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.

    1. Scope

    1.1 This consumer safety specification establishes performance requirements and test procedures to determine the structural integrity of full-size cribs. It also contains design requirements addressing entanglement on crib corner post extensions, and requirements for warning labels and instructional material. It also covers bassinet, changing table, or similar accessories to a crib that when in the manufacturer’s recommended use position are in the occupant retention area. These accessories shall also comply with the applicable requirements of the ASTM International standards addressing those accessories. For example, a changing table that attaches to a crib shall also comply with the applicable requirements in Consumer Safety Specification F2388. This specification does not cover inflatable products.

    1.2 No crib produced after the approval date of this consumer safety specification shall, either by label or other means, indicate compliance with this specification unless it conforms to all requirements contained herein.

    1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

    1.4 The following safety hazards caveat pertains only to the test methods portion, Section 7, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.


    2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    ASTM Standards

    D3359 Test Methods for Measuring Adhesion by Tape Test

    F963 Consumer Safety Specification for Toy Safety

    F2388 Consumer Safety Specification for Baby Changing Tables for Domestic Use

    Federal Standards

    16CFR1303 Ban of Lead-Containing Paint and Certain Consumer Products Bearing Lead-Containing Paint

    16CFR1500.3 Definitions

    16CFR1500.44 Method for Determining Extremely Flammable & Flammable Solids

    16CFR1500.48 Technical requirements for Determining a Sharp Point in Toys or Other Articles Intended for Use by Children Under Eight Years of Age

    16CFR1500.49 Technical Requirements for Determining a Sharp Metal or Glass Edge in Toys or Other Articles Intended for Use by Children Under Eight Years of Age

    16CFR1500.50–. Test Methods for Simulating Use and Abuse of Toys and Other Articles Intended for Use by Children

    16CFR1501 Method for Identifying Toys and Other Articles Intended for Use by Children Under Three Years of Age Which Present Choking, Aspiration or Ingestion Hazards Because of Small Parts


    ICS Code

    ICS Number Code 97.140 (Furniture); 97.190 (Equipment for children)

    UNSPSC Code

    UNSPSC Code 56101804(Cribs or playpens or accessories)


    DOI: 10.1520/F1169-13

    ASTM International is a member of CrossRef.

    ASTM F1169

    Citing ASTM Standards
    Back to Top