ASTM E662 - 14

    Standard Test Method for Specific Optical Density of Smoke Generated by Solid Materials

    Active Standard ASTM E662 | Developed by Subcommittee: E05.21

    Book of Standards Volume: 04.07


      Format Pages Price  
    PDF 25 $62.00   ADD TO CART
    Hardcopy (shipping and handling) 25 $62.00   ADD TO CART
    Standard + Redline PDF Bundle 50 $74.40   ADD TO CART


    Significance and Use

    5.1 This test method provides a means for determining the specific optical density of the smoke generated by specimens of materials and assemblies under the specified exposure conditions. Values determined by this test are specific to the specimen or assembly in the form and thickness tested and are not to be considered inherent fundamental properties of the material tested. Thus, it is likely that closely repeatable or reproducible experimental results are not to be expected from tests of a given material when specimen thickness, density, or other variables are involved.

    5.2 The photometric scale used to measure smoke by this test method is similar to the optical density scale for human vision. However, physiological aspects associated with vision are not measured by this test method. Correlation with measurements by other test methods has not been established.4

    5.3 At the present time no basis is provided for predicting the density of smoke generated by the materials upon exposure to heat and flame under other fire conditions.

    5.4 The test method is of a complex nature and the data obtained are sensitive to variations which in other test methods might be considered to be insignificant (see Section 6). A precision statement based on the results of a roundrobin test by a prior draft version of this test method is given in 14.1

    5.5 In this procedure, the specimens are subjected to one or more specific sets of laboratory test conditions. If different test conditions are substituted or the end-use conditions are changed, it is not always possible by or from this test method to predict changes in the fire-test-response characteristics measured. Therefore, the results are valid only for the fire test exposure conditions described in this procedure.

    1. Scope

    1.1 This fire-test-response standard covers determination of the specific optical density of smoke generated by solid materials and assemblies mounted in the vertical position in thicknesses up to and including 1 in. (25.4 mm).

    1.2 Measurement is made of the attenuation of a light beam by smoke (suspended solid or liquid particles) accumulating within a closed chamber due to nonflaming pyrolytic decomposition and flaming combustion.

    1.3 Results are expressed in terms of specific optical density which is derived from a geometrical factor and the measured optical density, a measurement characteristic of the concentration of smoke.

    1.4 This test method is intended for use in research and development and not as a basis for ratings for regulatory purposes.

    1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

    1.6 This standard measures and describes the response of materials, products, or assemblies to heat and flame under controlled conditions, but does not by itself incorporate all factors required for fire hazard or fire risk assessment of the materials, products or assemblies under actual fire conditions.

    1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.


    2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    ASTM Standards

    D2843 Test Method for Density of Smoke from the Burning or Decomposition of Plastics

    E176 Terminology of Fire Standards


    ICS Code

    ICS Number Code 13.220.40 (Ignitability and burning behaviour of materials and products); 17.180.99 (Other standards related to optics and optical measurements)

    UNSPSC Code

    UNSPSC Code


    Referencing This Standard

    DOI: 10.1520/E0662-14

    ASTM International is a member of CrossRef.

    Citation Format

    ASTM E662-14, Standard Test Method for Specific Optical Density of Smoke Generated by Solid Materials, ASTM International, West Conshohocken, PA, 2014, www.astm.org

    Back to Top