ASTM C141 / C141M - 09

    Standard Specification for Hydrated Hydraulic Lime for Structural Purposes

    Active Standard ASTM C141 / C141M | Developed by Subcommittee: C07.02

    Book of Standards Volume: 04.01


      Format Pages Price  
    PDF 3 $38.00   ADD TO CART
    Hardcopy (shipping and handling) 3 $38.00   ADD TO CART
    Standard + Redline PDF Bundle 6 $45.60   ADD TO CART


    Abstract

    This specification covers hydraulic hydrated lime for structural purposes. Hydraulic hydrated lime may be used in the scratch or brown coat of plaster, stucco, mortar, or in Portland-cement concrete either as blend, amendment, or admixture. The hydraulic hydrated lime shall conform to the chemical composition requirements for calcium oxide, magnesium oxide, silica, iron oxide, aluminum oxide, and carbon dioxide. The sample shall be subjected to the following test methods: chemical analysis; fineness; normal consistency; time of setting; autoclave expansion; and compressive strength.

    This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.

    1. Scope

    1.1 This specification covers hydrated hydraulic lime for structural purposes.

    1.2 Hydrated hydraulic lime may be used in the scratch or brown coat of plaster, stucco, mortar, or in portland-cement concrete either as blend, amendment, or admixture.

    1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the inch-pound units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

    1.4 The following precautionary caveat pertains only to the test method portion, Section 11 of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.


    2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    ASTM Standards

    C25 Test Methods for Chemical Analysis of Limestone, Quicklime, and Hydrated Lime

    C50 Practice for Sampling, Sample Preparation, Packaging, and Marking of Lime and Limestone Products

    C51 Terminology Relating to Lime and Limestone (as used by the Industry)

    C109/C109M Test Method for Compressive Strength of Hydraulic Cement Mortars (Using 2-in. or [50-mm] Cube Specimens)

    C110 Test Methods for Physical Testing of Quicklime, Hydrated Lime, and Limestone

    C187 Test Method for Amount of Water Required for Normal Consistency of Hydraulic Cement Paste

    C191 Test Methods for Time of Setting of Hydraulic Cement by Vicat Needle

    C230/C230M Specification for Flow Table for Use in Tests of Hydraulic Cement

    C270 Specification for Mortar for Unit Masonry

    C305 Practice for Mechanical Mixing of Hydraulic Cement Pastes and Mortars of Plastic Consistency

    C778 Specification for Sand


    ICS Code

    ICS Number Code 91.100.10 (Cement. Gypsum. Lime. Mortar)

    UNSPSC Code

    UNSPSC Code 30111604(Hydrated lime); 30111603(Hydraulic lime)


    DOI: 10.1520/C0141_C0141M-09

    ASTM International is a member of CrossRef.

    ASTM C141 / C141M

    Citing ASTM Standards
    Back to Top