ASTM F2620-12

    Standard Practice for Heat Fusion Joining of Polyethylene Pipe and Fittings

    SUPERSEDED (see Active link, below)


      Format Pages Price  
    PDF 25 $72.00   ADD TO CART


    1. Scope

    1.1 This practice describes procedures for making joints with polyethylene (PE) pipe and fittings by means of heat fusion joining in, but not limited to, a field environment. Other suitable heat fusion joining procedures are available from various sources including pipe and fitting manufacturers. This standard does not purport to address all possible heat fusion joining procedures, or to preclude the use of qualified procedures developed by other parties that have been proved to produce reliable heat fusion joints.

    1.2 The parameters and procedures are applicable only to joining polyethylene pipe and fittings of related polymer chemistry. They are intended for PE fuel gas pipe per Specification D2513 and PE potable water, sewer and industrial pipe manufactured per Specification F714, Specification D3035, and AWWA C901 and C906. Consult with the pipe manufacturers to make sure they approve this procedure for the pipe to be joined (see Appendix X1).

    Note 1Information about polyethylene pipe and fittings that have related polymer chemistry is presented in Plastics Pipe Institute (PPI) TR-33 and TR-41.

    1.3 Parts that are within the dimensional tolerances given in present ASTM specifications are required to produce sound joints between polyethylene pipe and fittings when using the joining techniques described in this practice.

    1.4 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.

    1.5 The text of this practice references notes, footnotes, and appendixes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the practice.

    1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.


    2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    ASTM Standards

    D2513 Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings

    D3035 Specification for Polyethylene (PE) Plastic Pipe (DR-PR) Based on Controlled Outside Diameter

    F714 Specification for Polyethylene (PE) Plastic Pipe (DR-PR) Based on Outside Diameter

    F1056 Specification for Socket Fusion Tools for Use in Socket Fusion Joining Polyethylene Pipe or Tubing and Fittings

    PPI Documents

    TR-33 Generic Butt Fusion Joining Procedure for Field Joining of Polyethylene Available from Plastics Pipe Institute (PPI), 105 Decker Court, Suite 825, Irving, TX 75062, http://www.plasticpipe.org.

    TR-41 Generic Saddle Fusion Joining Procedure for Polyethylene Gas Piping

    AWWA Documents

    AWWAC901 Standard for Polyethylene (PE) Pressure Pipe and Tubing, 12 in. (13 mm) through 3 in. (76 mm), for Water Service Available from American Water Works Association (AWWA), 6666 W. Quincy Ave., Denver, CO 80235, http://www.awwa.org.

    AWWAC906 Standard for Polyethylene (PE) Pressure Pipe and Fittings, 4 in. (100 mm) through 63 in. (1575 mm), for Water Distribution and Transmission


    ICS Code

    ICS Number Code 23.040.20 (Plastic pipes); 23.040.45 (Plastic fittings)

    UNSPSC Code

    UNSPSC Code 40171500(Commercial pipe and piping)


    DOI: 10.1520/F2620-12

    ASTM International is a member of CrossRef.


    Citing ASTM Standards
    Back to Top