Subcommittee F06.40 on Practices
Matching Standards Under the Jurisdiction of F06.40 by Status
- F1869-23 Standard Test Method for Measuring Moisture Vapor Emission Rate of Concrete Subfloor Using Anhydrous Calcium Chloride
- -See also WK85485 proposed Revision
- -See also WK85380 proposed Revision
- F2873-24 Standard Practice for the Installation of Self-Leveling Underlayment and the Preparation of Surface to Receive Resilient Flooring
- -See also WK92145 proposed Revision
- -See also WK92136 proposed Reapproval with Editorial Change
- F693-01(2023) Standard Practice for Sealing Seams of Resilient Sheet Flooring Products by Use of Liquid Seam Sealers
- F710-22 Standard Practice for Preparing Concrete Floors to Receive Resilient Flooring
- -See also WK86969 proposed Revision
- F1482-21 Standard Practice for Installation and Preparation of Panel Type Underlayments to Receive Resilient Flooring
- F1516-23 Standard Practice for Sealing Seams of Resilient Flooring Products by the Heat Weld Method (when Recommended)
- -See also WK84425 proposed Revision
- F2170-19a Standard Test Method for Determining Relative Humidity in Concrete Floor Slabs Using in situ Probes
- -See also WK50069 proposed Revision
- F2471-19 Standard Practice for Installation of Thick Poured Lightweight Cellular Concrete Underlayments and Preparation of the Surface to Receive Resilient Flooring
- F2659-23 Standard Guide for Preliminary Evaluation of Comparative Moisture Condition of Concrete, Gypsum Cement and Other Floor Slabs and Screeds Using a Non-Destructive Electronic Moisture Meter
- -See also WK93604 proposed Revision
- -See also WK78959 proposed Revision
- -See also WK93572 proposed Revision
- F3311-24 Standard Practice for Mat Bond Evaluation of Performance and Compatibility for Resilient Flooring System Components Prior to Installation
- F2419-11(2021) Standard Practice for Installation of Thick Poured Gypsum Concrete Underlayments and Preparation of the Surface to Receive Resilient Flooring
- F2678-16(2021) Standard Practice for Preparing Panel Underlayments, Thick Poured Gypsum Concrete Underlayments, Thick Poured Lightweight Cellular Concrete Underlayments, and Concrete Subfloors with Underlayment Patching Compounds to Receive Resilient Flooring
- F2753-21 Standard Practice to Evaluate the Effect of Dynamic Rolling Load over Resilient Floor Covering System
- F3010-24 Standard Practice for Two-Component Resin Based Membrane-Forming Moisture Mitigation Systems for Use Under Resilient Floor Coverings
- -See also WK91670 proposed Revision
- F3191-23 Standard Practice for Field Determination of Substrate Water Absorption (Porosity) for Substrates to Receive Resilient Flooring
- F3441-24a Standard Guide for Measurement of pH Involving Resilient Flooring Installations
- F3513-24 Standard Practice for Single Component, Fluid-Applied Membrane-Forming Moisture Mitigation Systems for Use Under Resilient Floor Coverings
- WK69827 Fluid-Applied Membrane-Forming Moisture Mitigation Systems for Use Under Resilient Floor Coverings
- WK82550 the Measurement of pH Below Resilient Flooring Installations
- WK90726 installation of resilient flooring
- E1907-06a Standard Guide to Methods of Evaluating Moisture Conditions of Concrete Floors to Receive Resilient Floor Coverings (Withdrawn 2008)
- F1102-94 Guide for Preparation of Use and Care Booklets for Residential Resilient Nontextile Floor Coverings (Withdrawn 2000)
- F1289-95 Practice for Development of Literature Pertaining to the Selection of Residential Resilient Floor Coverings (Withdrawn 2000)
- F1480-93 Guide for Preparing a Chart for Presenting Residential Resilient Floor Covering Information to the Consumer (Withdrawn 2000)
- F2420 Standard Test Method for Determining Relative Humidity on the Surface of Concrete Floor Slabs Using Relative Humidity Probe Measurement and Insulated Hood (Withdrawn 2014)
- F2420-05(2011) Standard Test Method for Determining Relative Humidity on the Surface of Concrete Floor Slabs Using Relative Humidity Probe Measurement and Insulated Hood (Withdrawn 2014)