Subcommittee F06.40 on Practices


    Showing results 1-15 of 15 matching ACTIVE standards under the jurisdiction of F06.40     F06 Home

    F693-01(2018)e1 Standard Practice for Sealing Seams of Resilient Sheet Flooring Products by Use of Liquid Seam Sealers

    F710-19e1 Standard Practice for Preparing Concrete Floors to Receive Resilient Flooring

        See also WK70598 proposed revision

    F1482-15 Standard Practice for Installation and Preparation of Panel Type Underlayments to Receive Resilient Flooring

    F1516-13(2018) Standard Practice for Sealing Seams of Resilient Flooring Products by the Heat Weld Method (when Recommended)

    F1869-16a Standard Test Method for Measuring Moisture Vapor Emission Rate of Concrete Subfloor Using Anhydrous Calcium Chloride

        See also WK64965 proposed revision

    F2170-19a Standard Test Method for Determining Relative Humidity in Concrete Floor Slabs Using in situ Probes

        See also WK64961 proposed revision

    F2419-11(2017) Standard Practice for Installation of Thick Poured Gypsum Concrete Underlayments and Preparation of the Surface to Receive Resilient Flooring

    F2471-19 Standard Practice for Installation of Thick Poured Lightweight Cellular Concrete Underlayments and Preparation of the Surface to Receive Resilient Flooring

        See also WK59552 proposed revision

    F2659-10(2015) Standard Guide for Preliminary Evaluation of Comparative Moisture Condition of Concrete, Gypsum Cement and Other Floor Slabs and Screeds Using a Non-Destructive Electronic Moisture Meter

    F2678-16 Standard Practice for Preparing Panel Underlayments, Thick Poured Gypsum Concrete Underlayments, Thick Poured Lightweight Cellular Concrete Underlayments, and Concrete Subfloors with Underlayment Patching Compounds to Receive Resilient Flooring

    F2753-10(2015) Standard Practice to Evaluate the Effect of Dynamic Rolling Load over Resilient Floor Covering System

        See also WK68917 proposed revision

    F2873-20 Standard Practice for the Installation of Self-Leveling Underlayment and the Preparation of Surface to Receive Resilient Flooring

        See also WK68827 proposed revision

    F3010-18 Standard Practice for Two-Component Resin Based Membrane-Forming Moisture Mitigation Systems for Use Under Resilient Floor Coverings

    F3191-16 Standard Practice for Field Determination of Substrate Water Absorption (Porosity) for Substrates to Receive Resilient Flooring

    F3311-19 Standard Practice for Mat Bond Evaluation of Performance and Compatibility for Resilient Flooring System Components Prior to Installation

    Showing results 1-3 of 3 matching Proposed New Standards under the jurisdiction of F06.40     F06 Home

    WK28850 New Practice for the Measurement of Surface pH of Concrete Floor Slabs.

    WK69827 One-Component Membrane-Forming Moisture Mitigation Systems for Use under Resilient Floor Coverings

    WK69831 Determining Substrate Surface pH for Concrete Floors to Receive Resilient Flooring

    Showing Results 1-4 of 4 matching WITHDRAWN standards under the jurisdiction of F06.40     F06 Home

    F1102-94 Guide for Preparation of Use and Care Booklets for Residential Resilient Nontextile Floor Coverings (Withdrawn 2000)

    F1289-95 Practice for Development of Literature Pertaining to the Selection of Residential Resilient Floor Coverings (Withdrawn 2000)

    F1480-93 Guide for Preparing a Chart for Presenting Residential Resilient Floor Covering Information to the Consumer (Withdrawn 2000)

    F2420-05(2011) Standard Test Method for Determining Relative Humidity on the Surface of Concrete Floor Slabs Using Relative Humidity Probe Measurement and Insulated Hood (Withdrawn 2014)