Work Item
ASTM WK11776
New Test Methods for Particle Size Distribution (Gradation) of Fine-Grained Soils Using the Sedimentation (Hydrometer) Analysis
1. Scope
1.1 This test method covers the quantitative determination of the distribution of particle sizes of the fine-grained portion of soils. The sedimentation or hydrometer method is used to determine the particle-size distribution (gradation) of the material that is finer than the No. 200 (75 m) sieve and larger than about 0.2 m. The test is performed on material passing the No. 10 (2.0 mm) or finer sieve and the results are presented as the mass percent finer versus the log of the particle diameter. 1.2 This test method can be used to evaluate the fine-grained fraction of a soil with a wide range of particle sizes by combining the sedimentation results with a sieve analysis resulting in the complete gradation curve. This test method can also be used when there are no coarse-grained particles or the gradation of the coarse-grained material is not required or not needed. NOTE 1-The significant digits recorded in this test method preclude obtaining the grain size distribution of materials that do not contain a significant amount of fines. For example, clean sands will not yield detectable amounts of silt and clay sized particles and, therefore, should not be tested with this test method. The minimum amount of fines in the sedimentation specimen is 15 g. 1.3 When combining the results of the sedimentation and sieve tests, the procedure for obtaining the material for the sedimentation analysis and calculations for combining the results will be provided by the more general test method, such as Test Method D6913 (NOTE 2). NOTE 2-Subcommittee D18.03 is currently developing a new test method Test Method for Particle-Size Analysis of Soils Combining The Sieve and Sedimentation Techniques. 1.4 The terms soil and material are used interchangeably throughout this test method. 1.5 The sedimentation analysis is based on the concept that larger particles will fall through a fluid faster than smaller particles. Stokes Law is the equation used to determine the terminal velocity of a spherical particle falling through a stationary liquid. The terminal velocity is proportional to the square of the particle diameter. Therefore, particles are sorted by size in both time and position when settling in a container of liquid. 1.5.1 Stokes Law has several assumptions that are: the particles are spherical and smooth, there is no interference between the particles, there is no difference between the current in the middle of the container and the sides, flow is laminar, and the particles have the same density. These assumptions are applied to soil particles of various shapes and sizes. 1.6 A hydrometer is used to measure the fluid density and determine the quantity of particles in suspension at a specific time and position. The density of the soil-water suspension depends upon the concentration and specific gravity of the soil particles and the amount of dispersant added. Each hydrometer measurement at an elapsed time is used to calculate the percentage of particles finer than the diameter given by Stokes Law. The series of readings provide the distribution of material mass as a function of particle size. 1.7 This test method does not cover procurement of the sample or processing of the sample before obtaining the reduced sample in any detail. It is assumed that the sample is obtained using appropriate methods and is representative of site materials or conditions. It is also assumed that the sample has been processed such that the reduced sample accurately reflects the particle-size distribution (gradation) of this finer fraction of the material. 1.8 Material Processing-Material is tested in the moist or as-received state unless the material is received in an air-dried state. The moist preparation method shall be used to obtain a sedimentation test specimen from the reduced sample. Air-dried preparation is only allowed when the material is received in the air-dried state. The method to be used may be specified by the requesting authority; however, the moist preparation method shall be used for referee testing. 1.9 This test method is not applicable for the following soils: 1.9.1 Soils containing fibrous peat; 1.9.2 Soils containing less than approximately 5 % of fine-grained material (NOTE 1); 1.9.3 Soils containing extraneous matter, such as organic solvents, oil, asphalt, wood fragments, or similar items (Note 3); and NOTE 3-If extraneous matter, such as wood, can be easily removed by hand, it is permissible to do so. However, there may be cases in which the extraneous matter is being evaluated as part of the material and it should not be removed from the material. 1.9.4 Materials that contain cementitious components, such as cement, fly ash, lime, or other stabilization admixtures. 1.10 This test method may not produce consistent test results within and between laboratories for the following soils. To test these soils, this test method shall be adapted or altered and these alterations documented. 1.10.1 Soils that flocculate during sedimentation. Such materials may need to be treated to reduce salinity or alter the pH of the suspension. 1.10.2 Friable soils in which processing changes the gradation of the soil. Typical examples of these soils are some residual soils, most weathered shales, and some weakly cemented soils. 1.10.3 Soils that will not readily disperse, such as glauconitic clays or some dried plastic clays. 1.11 Some materials that are not soils, but are made up of particles may be tested using this test method. The applicable sections above should be used in applying this test method. 1.12 Units-The values stated in SI units are to be regarded as the standard. Except the sieve designations, they are identified using the alternative system in accordance with Practice E11, such as 3 in. and No. 200, instead of the standard of 75 mm and 75m, respectively. Reporting of test results in units other than SI shall not be regarded as nonconformance with this test method. The use of balances or scales recording pounds of mass (lbm) shall not be regarded as nonconformance with this standard. 1.13 All observed and calculated values shall conform to the guidelines for significant digits and rounding established in Practice D6026, unless superseded by this test method. 1.13.1 The procedures used to specify how data are collected/recorded and calculated in this test method are regarded as the industry standard. In addition, they are representative of the significant digits that generally should be retained. The procedures used do not consider material variation, purpose for obtaining the data, special purpose studies, or any considerations for the users objectives; and it is common practice to increase or reduce significant digits of reported data to be commensurate with these considerations. It is beyond the scope of these test methods to consider significant digits used in analysis methods for engineering data. 1.14 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.Keywords
clay; silt; hydrometer analysis; particle-size distribution (gradation); sedimentation; sieve analysis; grain-sizeRationale
D422 combines both the hydrometer and sieving methods into one standard and there is not a method if a user only needs to perform a hydrometer analysis. There are times when only a sedimentation (hydrometer) analysis is needed or requested on a specimen. This standard provides the needed guidance on how to perform a sedimentation (hydrometer) analysis independent of any sieving. Once approved, this standard along with D6913 and the simplified combo standard, will provide users with appropriate guidance when it comes to deciding which standard theyll need to follow based on the test specimen and the requested analysis needed.
Work Item Status
Date Initiated: 06-19-2006
Technical Contact: Kendra Adams
Item: 001
Ballot: D18.03 (08-03)
Status: Will Reballot Item
Item: 002
Ballot: D18 (14-01)
Status: Will Reballot Item
Item: 003
Ballot: COS (16-04)
Status: Ballot Item Approved