Standard Active Last Updated: Jun 12, 2024 Track Document
ASTM D746-24

Standard Test Method for Brittleness Temperature of Plastics and Elastomers by Impact

Standard Test Method for Brittleness Temperature of Plastics and Elastomers by Impact D0746-24 ASTM|D0746-24|en-US Standard Test Method for Brittleness Temperature of Plastics and Elastomers by Impact Standard new BOS Vol. 08.01 Committee D20
$ 69.00 In stock
ASTM International

Significance and Use

5.1 This test method establishes the temperature at which 50 % of the specimens tested would probably fail when subjected to the conditions specified herein. The test provides for the evaluation of long-time effects such as crystallization, or those effects that are introduced by low-temperature incompatibility of plasticizers in the material under test. Plastics and elastomers are used in many applications requiring low-temperature flexing with or without impact. Use data obtained by this method to predict the behavior of plastic and elastomeric materials at low temperatures only in applications in which the conditions of deformation are similar to those specified in this test method. This test method has been found useful for specification purposes, but does not necessarily measure the lowest temperature at which the material is suitable for use.

FIG. 1 Dimensional Requirements Between Specimen Clamp and Striking Edge (Type A)

Dimensional Requirements Between Specimen Clamp and Striking Edge (Type A)Dimensional Requirements Between Specimen Clamp and Striking Edge (Type A)

FIG. 2 Typical Clamp (Type A)

Typical Clamp (Type A)

FIG. 3 Dimensional Details of Striking Edge and Clamping Device, Type B (Positioning of Unnotched Test Specimen)

Dimensional Details of Striking Edge and Clamping Device, Type B (Positioning of Unnotched Test Specimen)Dimensional Details of Striking Edge and Clamping Device, Type B (Positioning of Unnotched Test Specimen)

Note 1: Dimensions are in millimetres.

FIG. 4 Assembled Clamp with Test Specimens, Type B

Assembled Clamp with Test Specimens, Type BAssembled Clamp with Test Specimens, Type B

Scope

1.1 This test method covers the determination of the temperature at which plastics and elastomers (as defined by Terminology D883) exhibit brittle failure under specified impact conditions. Two routine inspection and acceptance procedures are also provided.

Note 1: When testing rubbers for impact brittleness use Test Method D2137. When testing plastic sheeting for impact brittleness, use Test Method D1790.

1.2 The values stated in SI units are to be regarded as the standard.

1.3 Due to the potential safety and environmental hazards associated with mercury-filled thermometers, the use of alternative temperature measuring devices (such as thermocouples and RTDs) is encouraged.

Warning—Mercury has been designated by many regulatory agencies as a hazardous material that can cause serious medical issues. Mercury, or its vapor, has been demonstrated to be hazardous to health and corrosive to materials. Caution should be taken when handling mercury and mercury containing products. See the applicable product Safety Data Sheet (SDS) for additional information. Users should be aware that selling mercury and/or mercury containing products into your state or country may be prohibited by law.

1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

Note 2: This test method and ISO 974 address the same subject matter, but differ in technical content.

1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Price:
Contact Sales
Related
Reprints and Permissions
Reprints and copyright permissions can be requested through the
Copyright Clearance Center
Details
Book of Standards Volume: 08.01
Developed by Subcommittee: D20.30
Pages: 8
DOI: 10.1520/D0746-24
ICS Code: 83.060; 83.080.01