New Building & Construction Standards

Search within Building & Construction


A6/A6M-17a: Standard Specification for General Requirements for Rolled Structural Steel Bars, Plates, Shapes, and Sheet Piling

C1644-06(2017): Standard Specification for Resilient Connectors Between Reinforced Concrete On-Site Wastewater Tanks and Pipes

D1779-98(2017): Standard Specification for Adhesive for Acoustical Materials

D1995-92(2017): Standard Test Methods for Multi-Modal Strength Testing of Autohesives (Contact Adhesives)

D2395-17: Standard Test Methods for Density and Specific Gravity (Relative Density) of Wood and Wood-Based Materials

C1134-17: Standard Test Method for Water Retention of Rigid Thermal Insulations Following Partial Immersion

C172/C172M-17: Standard Practice for Sampling Freshly Mixed Concrete

C496/C496M-17: Standard Test Method for Splitting Tensile Strength of Cylindrical Concrete Specimens

C618-17: Standard Specification for Coal Fly Ash and Raw or Calcined Natural Pozzolan for Use in Concrete

E1797-12(2017)e1: Standard Specification for Reinforced Liquid Coating Encapsulation Products for Leaded Paint in Buildings

D5456-17e1: Standard Specification for Evaluation of Structural Composite Lumber Products

C552-17: Standard Specification for Cellular Glass Thermal Insulation

C989/C989M-17: Standard Specification for Slag Cement for Use in Concrete and Mortars

F588-17: Standard Test Methods for Measuring the Forced Entry Resistance of Window Assemblies, Excluding Glazing Impact

F842-17: Standard Test Methods for Measuring the Forced Entry Resistance of Sliding Door Assemblies, Excluding Glazing Impact

F1193-17: Standard Practice for Quality, Manufacture, and Construction of Amusement Rides and Devices

C712-14: Standard Test Method for Bubbling of One-Part, Elastomeric, Solvent-Release Type Sealants

C880/C880M-15: Standard Test Method for Flexural Strength of Dimension Stone

D6155-15: Standard Specification for Nontraditional Coarse Aggregates for Bituminous Paving Mixtures

C11-17a: Standard Terminology Relating to Gypsum and Related Building Materials and Systems

C335/C335M-17: Standard Test Method for Steady-State Heat Transfer Properties of Pipe Insulation

E1825-17: Standard Guide for Evaluation of Exterior Building Wall Materials, Products, and Systems

C656-17: Standard Specification for Structural Insulating Board, Calcium Silicate

C1222-17: Standard Practice for Evaluation of Laboratories Testing Hydraulic Cement

C840-17a: Standard Specification for Application and Finishing of Gypsum Board

C957/C957M-17: Standard Specification for High-Solids Content, Cold Liquid-Applied Elastomeric Waterproofing Membrane With Integral Wearing Surface

C1115-17: Standard Specification for Dense Elastomeric Silicone Rubber Gaskets and Accessories

C1149-17: Standard Specification for Self-Supported Spray Applied Cellulosic Thermal Insulation

C1483/C1483M-17: Standard Specification for Exterior Solar Radiation Control Coatings on Buildings

C1785-17: Standard Test Method for Concentration of Pinhole Detections in Moisture Barriers on Metal Jacketing

C1130-17: Standard Practice for Calibration of Thin Heat Flux Transducers

C1064/C1064M-17: Standard Test Method for Temperature of Freshly Mixed Hydraulic-Cement Concrete

D3549/D3549M-17: Standard Test Method for Thickness or Height of Compacted Asphalt Mixture Specimens

D7403-09(2017): Standard Test Method for Determination of Residue of Emulsified Asphalt by Low-Temperature Vacuum Distillation

C62-17: Standard Specification for Building Brick (Solid Masonry Units Made From Clay or Shale)

C216-17a: Standard Specification for Facing Brick (Solid Masonry Units Made from Clay or Shale)

C652-17a: Standard Specification for Hollow Brick (Hollow Masonry Units Made From Clay or Shale)

C1077-17: Standard Practice for Agencies Testing Concrete and Concrete Aggregates for Use in Construction and Criteria for Testing Agency Evaluation

C1088-17: Standard Specification for Thin Veneer Brick Units Made From Clay or Shale

D2915-17: Standard Practice for Sampling and Data-Analysis for Structural Wood and Wood-Based Products

D7226-13(2017): Standard Test Method for Determining the Viscosity of Emulsified Asphalts Using a Rotational Paddle Viscometer

D7402-09(2017): Standard Practice for Identifying Cationic Emulsified Asphalts

C157/C157M-17: Standard Test Method for Length Change of Hardened Hydraulic-Cement Mortar and Concrete

D1036-99(2017): Standard Test Methods of Static Tests of Wood Poles

D2899-12(2017): Standard Practice for Establishing Allowable Stresses for Round Timber Piles

D4592-12(2017): Standard Specification for Preformed Retroreflective Pavement Marking Tape for Limited Service Life

D5404/D5404M-12(2017): Standard Practice for Recovery of Asphalt from Solution Using the Rotary Evaporator

D5821-13(2017): Standard Test Method for Determining the Percentage of Fractured Particles in Coarse Aggregate

D6390-11(2017): Standard Test Method for Determination of Draindown Characteristics in Uncompacted Asphalt Mixtures

E1592-05(2017): Standard Test Method for Structural Performance of Sheet Metal Roof and Siding Systems by Uniform Static Air Pressure Difference

E1996-17: Standard Specification for Performance of Exterior Windows, Curtain Walls, Doors, and Impact Protective Systems Impacted by Windborne Debris in Hurricanes

A888-17a: Standard Specification for Hubless Cast Iron Soil Pipe and Fittings for Sanitary and Storm Drain, Waste, and Vent Piping Applications

C1438-13(2017): Standard Specification for Latex and Powder Polymer Modifiers for use in Hydraulic Cement Concrete and Mortar

D25-12(2017): Standard Specification for Round Timber Piles

D2399-12(2017)e1: Standard Practice for Selection of Cutback Asphalts

D3200-74(2017): Standard Specification and Test Method for Establishing Recommended Design Stresses for Round Timber Construction Poles

D3665-12(2017): Standard Practice for Random Sampling of Construction Materials

D4505-12(2017): Standard Specification for Preformed Retroreflective Pavement Marking Tape for Extended Service Life

D244-09(2017): Standard Test Methods and Practices for Emulsified Asphalts

D448-12(2017): Standard Classification for Sizes of Aggregate for Road and Bridge Construction

F2200-17: Standard Specification for Automated Vehicular Gate Construction

A1056-12(2017): Standard Specification for Cast Iron Couplings Used for Joining Hubless Cast Iron Soil Pipe and Fittings

C1461-08(2017): Standard Specification for Mechanical Couplings Using Thermoplastic Elastomeric (TPE) Gaskets for Joining Drain, Waste, and Vent (DWV), Sewer, Sanitary, and Storm Plumbing Systems for Above and Below Ground Use

C1541-12(2017): Standard Specification for Shielded Transition Couplings Using Flexible Polyvinyl Chloride (PVC) Gaskets to Connect Dissimilar DWV Pipe and Fittings

C1563-08(2017): Standard Test Method for Gaskets for Use in Connection with Hub and Spigot Cast Iron Soil Pipe and Fittings for Sanitary Drain, Waste, Vent, and Storm Piping Applications

D5791-95(2017): Standard Guide for Using Probability Sampling Methods in Studies of Indoor Air Quality in Buildings

A74-17: Standard Specification for Cast Iron Soil Pipe and Fittings

A861-04(2017): Standard Specification for High-Silicon Iron Pipe and Fittings

D4956-17: Standard Specification for Retroreflective Sheeting for Traffic Control

F710-17: Standard Practice for Preparing Concrete Floors to Receive Resilient Flooring

D2555-17a: Standard Practice for Establishing Clear Wood Strength Values

D6935-17: Standard Test Method for Determining Cement Mixing of Emulsified Asphalt

E2357-17: Standard Test Method for Determining Air Leakage of Air Barrier Assemblies

C311/C311M-17: Standard Test Methods for Sampling and Testing Fly Ash or Natural Pozzolans for Use in Portland-Cement Concrete

C635/C635M-17: Standard Specification for Manufacture, Performance, and Testing of Metal Suspension Systems for Acoustical Tile and Lay-in Panel Ceilings

C1265-17: Standard Test Method for Determining the Tensile Properties of an Insulating Glass Edge Seal for Structural Glazing Applications

E580/E580M-17: Standard Practice for Installation of Ceiling Suspension Systems for Acoustical Tile and Lay-in Panels in Areas Subject to Earthquake Ground Motions

E2265-17: Standard Terminology for Anchors and Fasteners in Concrete and Masonry

F2170-17: Standard Test Method for Determining Relative Humidity in Concrete Floor Slabs Using in situ Probes

C1519-10(2017): Standard Test Method for Evaluating Durability of Building Construction Sealants by Laboratory Accelerated Weathering Procedures

D4227-05(2017): Standard Practice for Qualification of Coating Applicators for Application of Coatings to Concrete Surfaces

D4258-05(2017): Standard Practice for Surface Cleaning Concrete for Coating

D4260-05(2017): Standard Practice for Liquid and Gelled Acid Etching of Concrete

D7496-17: Standard Test Method for Viscosity of Emulsified Asphalt by Saybolt Furol Viscometer

D6528-17: Standard Test Method for Consolidated Undrained Direct Simple Shear Testing of Fine Grain Soils

C156-17: Standard Test Method for Water Loss [from a Mortar Specimen] Through Liquid Membrane-Forming Curing Compounds for Concrete

C665-17: Standard Specification for Mineral-Fiber Blanket Thermal Insulation for Light Frame Construction and Manufactured Housing

C764-17: Standard Specification for Mineral Fiber Loose-Fill Thermal Insulation

D7508/D7508M-10(2015): Standard Specification for Polyolefin Chopped Strands for Use in Concrete

E2912-17: Standard Test Method for Fire Test of Non-Mechanical Fire Dampers Used in Vented Construction

C1482-17: Standard Specification for Polyimide Flexible Cellular Thermal and Sound Absorbing Insulation

C728-17a: Standard Specification for Perlite Thermal Insulation Board

C1364-17: Standard Specification for Architectural Cast Stone

C1613-17: Standard Specification for Precast Concrete Grease Interceptor Tanks

D5319-17: Standard Specification for Glass-Fiber Reinforced Polyester Wall and Ceiling Panels

A955/A955M-17a: Standard Specification for Deformed and Plain Stainless-Steel Bars for Concrete Reinforcement

C1756-17: Standard Guide for Comparing Seal or Sealant Behavior to Reference Photographs

A709/A709M-17: Standard Specification for Structural Steel for Bridges

A1075-12(2017)e1: Standard Specification for Flanged Steel U-Channel Posts

C461-17: Standard Test Methods for Mastics and Coatings Used With Thermal Insulation

C547-17: Standard Specification for Mineral Fiber Pipe Insulation

C578-17a: Standard Specification for Rigid, Cellular Polystyrene Thermal Insulation

C591-17: Standard Specification for Unfaced Preformed Rigid Cellular Polyisocyanurate Thermal Insulation

A767/A767M-16: Standard Specification for Zinc-Coated (Galvanized) Steel Bars for Concrete Reinforcement

A786/A786M-15: Standard Specification for Hot-Rolled Carbon, Low-Alloy, High-Strength Low-Alloy, and Alloy Steel Floor Plates

A910/A910M-16: Standard Specification for Uncoated, Weldless, 2-Wire and 3-Wire Steel Strand for Prestressed Concrete

A950/A950M-11(2015): Standard Specification for Fusion-Bonded Epoxy-Coated Structural Steel H-Piles and Sheet Piling

C443-12(2017): Standard Specification for Joints for Concrete Pipe and Manholes, Using Rubber Gaskets

C443M-11(2017): Standard Specification for Joints for Concrete Pipe and Manholes, Using Rubber Gaskets (Metric)

C1619-11(2017): Standard Specification for Elastomeric Seals for Joining Concrete Structures

C1677-11a(2017): Standard Specification for Joints for Concrete Box, Using Rubber Gaskets

D7290-06(2017): Standard Practice for Evaluating Material Property Characteristic Values for Polymeric Composites for Civil Engineering Structural Applications

D7616/D7616M-11(2017): Standard Test Method for Determining Apparent Overlap Splice Shear Strength Properties of Wet Lay-Up Fiber-Reinforced Polymer Matrix Composites Used for Strengthening Civil Structures

D7617/D7617M-11(2017): Standard Test Method for Transverse Shear Strength of Fiber-reinforced Polymer Matrix Composite Bars

E2358-17: Standard Specification for Performance of Glazing in Permanent Railing Systems, Guards, and Balustrades

A184/A184M-17: Standard Specification for Welded Deformed Steel Bar Mats for Concrete Reinforcement

A704/A704M-17: Standard Specification for Welded Steel Plain Bar or Rod Mats for Concrete Reinforcement

D6936-17: Standard Test Method for Determining Demulsibility of Emulsified Asphalt

E987-88(2017): Standard Test Methods for Deglazing Force of Fenestration Products

E1509-12(2017): Standard Specification for Room Heaters, Pellet Fuel-Burning Type

E1602-03(2017): Standard Guide for Construction of Solid Fuel Burning Masonry Heaters

E1612/E1612M-94(2017): Standard Specification for Preformed Architectural Compression Seals for Buildings and Parking Structures

E1748-95(2017): Standard Test Method for Evaluating the Engagement Between Windows and Insect Screens as an Integral System

E1783/E1783M-96(2017): Standard Specification for Preformed Architectural Strip Seals for Buildings and Parking Structures

E1827-11(2017): Standard Test Methods for Determining Airtightness of Buildings Using an Orifice Blower Door

E2515-11(2017): Standard Test Method for Determination of Particulate Matter Emissions Collected by a Dilution Tunnel

E2779-10(2017): Standard Test Method for Determining Particulate Matter Emissions from Pellet Heaters

E2780-10(2017): Standard Test Method for Determining Particulate Matter Emissions from Wood Heaters

F1866-13(2017): Standard Specification for Poly (Vinyl Chloride) (PVC) Plastic Schedule 40 Drainage and DWV Fabricated Fittings

F2390-12(2017): Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent (DWV) Pipe and Fittings Having Post-Industrial Recycle Content

F2946-12(2017): Standard Specification for PVC Hub and Elastomeric Seal (Gasket) Tee Connection for Joining Plastic Pipe to Insitu Pipelines and Manholes

D4796-17: Standard Test Method for Bond Strength of Thermoplastic Pavement Marking Materials

E741-11(2017): Standard Test Method for Determining Air Change in a Single Zone by Means of a Tracer Gas Dilution

E1399/E1399M-97(2017): Standard Test Method for Cyclic Movement and Measuring the Minimum and Maximum Joint Widths of Architectural Joint Systems

E2751/E2751M-17a: Standard Practice for Design and Performance of Supported Laminated Glass Walkways

F2764/F2764M-17e1: Standard Specification for 6 to 60 in. [150 to 1500 mm] Polypropylene (PP) Corrugated Double and Triple Wall Pipe and Fittings for Non-Pressure Sanitary Sewer Applications

D2394-17: Standard Test Methods for Simulated Service Testing of Wood and Wood-Based Finish Flooring

C919-12(2017): Standard Practice for Use of Sealants in Acoustical Applications

C1021-08(2014): Standard Practice for Laboratories Engaged in Testing of Building Sealants

C1712-17: Standard Test Method for Rapid Assessment of Static Segregation Resistance of Self-Consolidating Concrete Using Penetration Test

C1721-15: Standard Guide for Petrographic Examination of Dimension Stone

D3311-17: Standard Specification for Drain, Waste, and Vent (DWV) Plastic Fittings Patterns

F1675-13(2017): Standard Practice for Life-Cycle Cost Analysis of Plastic Pipe Used for Culverts, Storm Sewers, and Other Buried Conduits

C778-17: Standard Specification for Standard Sand

C1372-17: Standard Specification for Dry-Cast Segmental Retaining Wall Units

C1623-17a: Standard Specification for Manufactured Concrete Masonry Lintels

C471M-17e1: Standard Test Methods for Chemical Analysis of Gypsum and Gypsum Products (Metric)

C1670/C1670M-17: Standard Specification for Adhered Manufactured Stone Masonry Veneer Units

E1186-17: Standard Practices for Air Leakage Site Detection in Building Envelopes and Air Barrier Systems

C1621/C1621M-17: Standard Test Method for Passing Ability of Self-Consolidating Concrete by J-Ring

C1675-17a: Standard Practice for Installation of Precast Reinforced Concrete Monolithic Box Sections for Culverts, Storm Drains, and Sewers

D2643/D2643M-08(2013)e1: Standard Specification for Prefabricated Bituminous Geomembrane Used as Canal and Ditch Liner (Exposed Type)

D7001-06(2011): Standard Specification for Geocomposites for Pavement Edge Drains and Other High-Flow Applications

D7239-13: Standard Specification for Hybrid Geosynthetic Paving Mat for Highway Applications

D906-98(2017): Standard Test Method for Strength Properties of Adhesives in Plywood Type Construction in Shear by Tension Loading

D2339-98(2017): Standard Test Method for Strength Properties of Adhesives in Two-Ply Wood Construction in Shear by Tension Loading

D5824-98(2017): Standard Test Method for Determining Resistance to Delamination of Adhesive Bonds in Overlay-Wood Core Laminates Exposed to Heat and Water

E84-17: Standard Test Method for Surface Burning Characteristics of Building Materials

C94/C94M-17a: Standard Specification for Ready-Mixed Concrete

C1608-17: Standard Test Method for Chemical Shrinkage of Hydraulic Cement Paste

D7735-17: Standard Test Method for Type A Durometer Hardness Testing of Thermoplastic Pavement Marking at Elevated Temperatures

C39/C39M-17b: Standard Test Method for Compressive Strength of Cylindrical Concrete Specimens

C117-17: Standard Test Method for Materials Finer than 75-μm (No. 200) Sieve in Mineral Aggregates by Washing

D4439-17: Standard Terminology for Geosynthetics

D5898/D5898M-96(2013): Standard Guide for Standard Details for Adhered Sheet Waterproofing

E2883-13: Standard Guide for Standard Guide for the Evaluation, and Calibration, Continuous Friction Measurement Equipment (CFME)

F934-96(2017): Standard Specification for Standard Colors for Polymer-Coated Chain Link Fence Materials

C739-17: Standard Specification for Cellulosic Fiber Loose-Fill Thermal Insulation

C1157/C1157M-17: Standard Performance Specification for Hydraulic Cement

D8-17c: Standard Terminology Relating to Materials for Roads and Pavements

D6878/D6878M-17: Standard Specification for Thermoplastic Polyolefin Based Sheet Roofing

C1038/C1038M-14b: Standard Test Method for Expansion of Hydraulic Cement Mortar Bars Stored in Water

C1073-12: Standard Test Method for Hydraulic Activity of Slag Cement by Reaction with Alkali

C1148-92a(2014): Standard Test Method for Measuring the Drying Shrinkage of Masonry Mortar

C1252-17: Standard Test Methods for Uncompacted Void Content of Fine Aggregate (as Influenced by Particle Shape, Surface Texture, and Grading)

C1328/C1328M-12: Standard Specification for Plastic (Stucco) Cement

C1329/C1329M-16a: Standard Specification for Mortar Cement

C1384-12a: Standard Specification for Admixtures for Masonry Mortars

C1403-15: Standard Test Method for Rate of Water Absorption of Masonry Mortars

C1439-13: Standard Test Methods for Evaluating Latex and Powder Polymer Modifiers for use in Hydraulic Cement Concrete and Mortar

C1582/C1582M-11(2017)e1: Standard Specification for Admixtures to Inhibit Chloride-Induced Corrosion of Reinforcing Steel in Concrete

C1679-14: Standard Practice for Measuring Hydration Kinetics of Hydraulic Cementitious Mixtures Using Isothermal Calorimetry

C1707-11: Standard Specification for Pozzolanic Hydraulic Lime for Structural Purposes

C1708/C1708M-16: Standard Test Methods for Self-leveling Mortars Containing Hydraulic Cements

C1761/C1761M-17: Standard Specification for Lightweight Aggregate for Internal Curing of Concrete

D1734-93(2013): Standard Practice for Making Cementitious Panels for Testing Coatings

D3319-11(2017): Standard Practice for the Accelerated Polishing of Aggregates Using the British Wheel

D7088-17: Standard Practice for Resistance to Hydrostatic Pressure for Coatings Used in Below Grade Applications Applied to Masonry

D7505/D7505M-17: Standard Specification for Self-Adhesive Polyester Fabric Reinforced Polymer Modified Asphalt Steep Slope Roll Roofing Surfaced with Mineral Granules

E518/E518M-15: Standard Test Methods for Flexural Bond Strength of Masonry

C472-99(2014): Standard Test Methods for Physical Testing of Gypsum, Gypsum Plasters and Gypsum Concrete

C518-17: Standard Test Method for Steady-State Thermal Transmission Properties by Means of the Heat Flow Meter Apparatus

C596-09(2017): Standard Test Method for Drying Shrinkage of Mortar Containing Hydraulic Cement

C806-12: Standard Test Method for Restrained Expansion of Expansive Cement Mortar

C807-13: Standard Test Method for Time of Setting of Hydraulic Cement Mortar by Modified Vicat Needle

C884/C884M-16: Standard Test Method for Thermal Compatibility Between Concrete and an Epoxy-Resin Overlay

C928/C928M-13: Standard Specification for Packaged, Dry, Rapid-Hardening Cementitious Materials for Concrete Repairs

C932-06(2013): Standard Specification for Surface-Applied Bonding Compounds for Exterior Plastering

C1012/C1012M-15: Standard Test Method for Length Change of Hydraulic-Cement Mortars Exposed to a Sulfate Solution

C1017/C1017M-13e1: Standard Specification for Chemical Admixtures for Use in Producing Flowing Concrete

C1610/C1610M-17: Standard Test Method for Static Segregation of Self-Consolidating Concrete Using Column Technique

D7530/D7530M-17: Standard Specification for Self-Adhesive Glass Fiber Fabric Reinforced Polymer Modified Asphalt Steep Slope Roll Roofing Surfaced with Mineral Granules

E2611-17: Standard Test Method for Normal Incidence Determination of Porous Material Acoustical Properties Based on the Transfer Matrix Method

C10/C10M-14: Standard Specification for Natural Cement

C28/C28M-10(2015): Standard Specification for Gypsum Plasters

C91/C91M-12: Standard Specification for Masonry Cement

C109/C109M-16a: Standard Test Method for Compressive Strength of Hydraulic Cement Mortars (Using 2-in. or [50-mm] Cube Specimens)

C141/C141M-14: Standard Specification for Hydrated Hydraulic Lime for Structural Purposes

C185-15a: Standard Test Method for Air Content of Hydraulic Cement Mortar

C207-06(2011): Standard Specification for Hydrated Lime for Masonry Purposes

C305-14: Standard Practice for Mechanical Mixing of Hydraulic Cement Pastes and Mortars of Plastic Consistency

C348-14: Standard Test Method for Flexural Strength of Hydraulic-Cement Mortars

C359-13: Standard Test Method for Early Stiffening of Hydraulic Cement (Mortar Method)

C418-12: Standard Test Method for Abrasion Resistance of Concrete by Sandblasting

E2404-17: Standard Practice for Specimen Preparation and Mounting of Textile, Paper or Polymeric (Including Vinyl) and Wood Wall or Ceiling Coverings, Facings and Veneers, to Assess Surface Burning Characteristics

C31/C31M-17: Standard Practice for Making and Curing Concrete Test Specimens in the Field

C641-17: Standard Test Method for Iron Staining Materials in Lightweight Concrete Aggregates

C1202-17: Standard Test Method for Electrical Indication of Concrete's Ability to Resist Chloride Ion Penetration

C1288-17: Standard Specification for Fiber-Cement Interior Substrate Sheets

E2394-11: Standard Practice for Maintenance, Renovation and Repair of Installed Asbestos Cement Products

C331/C331M-17: Standard Specification for Lightweight Aggregates for Concrete Masonry Units

C332-17: Standard Specification for Lightweight Aggregates for Insulating Concrete

C494/C494M-17: Standard Specification for Chemical Admixtures for Concrete

C627-10e1: Standard Test Method for Evaluating Ceramic Floor Tile Installation Systems Using the Robinson-Type Floor Tester

C1289-17: Standard Specification for Faced Rigid Cellular Polyisocyanurate Thermal Insulation Board

D7445-17: Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding with Foam Plastic Backing (Backed Vinyl Siding)

E970-17: Standard Test Method for Critical Radiant Flux of Exposed Attic Floor Insulation Using a Radiant Heat Energy Source

C34-17: Standard Specification for Structural Clay Loadbearing Wall Tile

C67-17: Standard Test Methods for Sampling and Testing Brick and Structural Clay Tile

C140/C140M-17a: Standard Test Methods for Sampling and Testing Concrete Masonry Units and Related Units

C212-17: Standard Specification for Structural Clay Facing Tile

C279-17: Standard Specification for Chemical-Resistant Masonry Units

C330/C330M-17a: Standard Specification for Lightweight Aggregates for Structural Concrete

C780-17: Standard Test Method for Preconstruction and Construction Evaluation of Mortars for Plain and Reinforced Unit Masonry

C980-17: Standard Specification for Industrial Chimney Lining Brick

C1232-17: Standard Terminology for Masonry

C1325-17a: Standard Specification for Non-Asbestos Fiber-Mat Reinforced Cementitious Backer Units

C1634-17: Standard Specification for Concrete Facing Brick

C1713-17: Standard Specification for Mortars for the Repair of Historic Masonry

C1780-17: Standard Practice for Installation Methods for Adhered Manufactured Stone Masonry Veneer

D3679-17: Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding

D7254-17: Standard Specification for Polypropylene (PP) Siding

D7793-17: Standard Specification for Insulated Vinyl Siding

C637-14: Standard Specification for Aggregates for Radiation-Shielding Concrete

C638-14: Standard Descriptive Nomenclature of Constituents of Aggregates for Radiation-Shielding Concrete

D4799/D4799M-17: Standard Practice for Accelerated Weathering Test Conditions and Procedures for Bituminous Materials (Fluorescent UV, Water Spray, and Condensation Method)

D1571/D1571M-95(2017): Standard Specification for Woven Asbestos Cloth

D1573/D1573M-95(2017): Standard Test Method for Heat Aging of Asbestos Textiles

D1918/D1918M-95(2017): Standard Test Method for Asbestos Content of Asbestos Textiles

D2100/D2100M-95(2017): Standard Specification for Asbestos Textiles Used for Electrical Insulating Purposes

D3880/D3880M-90(2017): Standard Test Method for Asbestos Strength Units

C1400-11(2017): Standard Guide for Reduction of Efflorescence Potential in New Masonry Walls

C1693-11(2017): Standard Specification for Autoclaved Aerated Concrete (AAC)

C1694-09(2017): Standard Specification for Reinforced Autoclaved Aerated Concrete (AAC) Elements

C1719-11(2017): Standard Test Method for Installed Precast Concrete Tanks and Accessories by the Negative Air Pressure (Vacuum) Test Prior to Backfill

D299/D299M-04(2017): Standard Specification for Asbestos Yarns

D315/D315M-95(2017): Standard Specification for Woven Asbestos Tape

D375/D375M-95(2017): Standard Specification for Asbestos Roving

D628/D628M-95(2017): Standard Specification for Asbestos Tubular Sleeving

D1061/D1061M-95(2017): Standard Specification for Asbestos Lap

D1118/D1118M-95(2017): Standard Test Method for Magnetic Rating of Asbestos Fiber and Asbestos Textiles

D2793-99(2017): Standard Test Method for Block Resistance of Organic Coatings on Wood Panel Substrates

E850-10: Standard Guide for Characterization of Inorganic Process Wastes for Use as Structural Fill

F2049-11(2017): Standard Safety Performance Specification for Fences/Barriers for Public, Commercial, and Multi-Family Residential Use Outdoor Play Areas

C1686-09(2017): Standard Practice for Installation and Testing of Reinforced Autoclaved Aerated Concrete (AAC) Units

D4016-14: Standard Test Method for Viscosity and Gel Time of Chemical Grouts by Rotational Viscometer (Laboratory Method)

D4320/D4320M-09: Standard Practice for Laboratory Preparation of Chemically Grouted Soil Specimens for Obtaining Engineering Parameters

D6910/D6910M-09: Standard Test Method for Marsh Funnel Viscosity of Clay Construction Slurries

C55-17: Standard Specification for Concrete Building Brick

C73-17: Standard Specification for Calcium Silicate Brick (Sand-Lime Brick)

C129-17: Standard Specification for Nonloadbearing Concrete Masonry Units

C139-17: Standard Specification for Concrete Masonry Units for Construction of Catch Basins and Manholes

C1272-17: Standard Specification for Heavy Vehicular Paving Brick

C1319-17: Standard Specification for Concrete Grid Paving Units

C1396/C1396M-17: Standard Specification for Gypsum Board

D1792-17: Standard Test Method for Long-Term Removability Properties of Emulsion Floor Polishes

D6931-17: Standard Test Method for Indirect Tensile (IDT) Strength of Asphalt Mixtures

F1859-14e1: Standard Specification for Rubber Sheet Floor Covering Without Backing

E2034-99(2017): Standard Practices for Simulating Truck Response to Longitudinal Profiles of Vehicular Traveled Surfaces

D226/D226M-17: Standard Specification for Asphalt-Saturated Organic Felt Used in Roofing and Waterproofing

D2835-89(2017): Standard Specification for Lubricant for Installation of Preformed Compression Seals in Concrete Pavements

D5973-97(2017): Standard Specification for Elastomeric Strip Seals with Steel Locking Edge Rails Used in Expansion Joint Sealing

D6924-03(2017): Standard Specification for Preformed Thermoplastic Vulcanizate Elastomeric Joint Seals for Bridges

E1170-97(2017): Standard Practices for Simulating Vehicular Response to Longitudinal Profiles of Traveled Surfaces

C87/C87M-17: Standard Test Method for Effect of Organic Impurities in Fine Aggregate on Strength of Mortar

C174/C174M-17: Standard Test Method for Measuring Thickness of Concrete Elements Using Drilled Concrete Cores

C1218/C1218M-17: Standard Test Method for Water-Soluble Chloride in Mortar and Concrete

F654-07(2017): Standard Specification for Residential Chain Link Fence Gates

F900-11(2017): Standard Specification for Industrial and Commercial Steel Swing Gates

F1183-96(2017): Standard Specification for Aluminum Alloy Chain Link Fence Fabric

F1553-11(2017): Standard Guide for Specifying Chain Link Fence

C294-12(2017): Standard Descriptive Nomenclature for Constituents of Concrete Aggregates

C823/C823M-12(2017): Standard Practice for Examination and Sampling of Hardened Concrete in Constructions

D5516-17: Standard Test Method for Evaluating the Flexural Properties of Fire-Retardant Treated Softwood Plywood Exposed to Elevated Temperatures

D5664-17: Standard Test Method for Evaluating the Effects of Fire-Retardant Treatments and Elevated Temperatures on Strength Properties of Fire-Retardant Treated Lumber

C231/C231M-17a: Standard Test Method for Air Content of Freshly Mixed Concrete by the Pressure Method

D2792-17: Standard Practice for Solvent and Fuel Resistance of Traffic Paint

D7308-17: Standard Practice for Sample Preparation of Thermoplastic Pavement Marking Materials

D1461-17: Standard Test Method for Moisture or Volatile Distillates in Asphalt Mixtures

C907-17: Standard Test Method for Tensile Adhesive Strength of Preformed Tape Sealants by Disk Method

D2726/D2726M-17: Standard Test Method for Bulk Specific Gravity and Density of Non-Absorptive Compacted Asphalt Mixtures

D5801-17: Standard Test Method for Toughness and Tenacity of Asphalt Materials

C29/C29M-17a: Standard Test Method for Bulk Density (“Unit Weight”) and Voids in Aggregate

D977-17: Standard Specification for Emulsified Asphalt

D2397/D2397M-17: Standard Specification for Cationic Emulsified Asphalt

E2634-17: Standard Specification for Flat Wall Insulating Concrete Form (ICF) Systems

C356-17: Standard Test Method for Linear Shrinkage of Preformed High-Temperature Thermal Insulation Subjected to Soaking Heat

C896-17: Standard Terminology Relating to Clay Products

C1057-17: Standard Practice for Determination of Skin Contact Temperature from Heated Surfaces Using a Mathematical Model and Thermesthesiometer

D7063/D7063M-17: Standard Test Method for Effective Porosity and Effective Air Voids of Compacted Asphalt Mixture Samples

C786/C786M-10(2016): Standard Test Method for Fineness of Hydraulic Cement and Raw Materials by the 300-μm (No. 50), 150-μm (No. 100), and 75-μm (No. 200) Sieves by Wet Methods

C845/C845M-12: Standard Specification for Expansive Hydraulic Cement

C977-10: Standard Specification for Quicklime and Hydrated Lime for Soil Stabilization

C1063-17a: Standard Specification for Installation of Lathing and Furring to Receive Interior and Exterior Portland Cement-Based Plaster

C1381/C1381M-97(2013): Standard Specification for Molded Glass Fiber Reinforced Gypsum Parts

C1658/C1658M-13: Standard Specification for Glass Mat Gypsum Panels

D7227/D7227M-17: Standard Practice for Rapid Drying of Compacted Asphalt Mixture Specimens Using Vacuum Drying Apparatus

E2560-17: Standard Specification for Data Format for Pavement Profile

A392-11a(2017): Standard Specification for Zinc-Coated Steel Chain-Link Fence Fabric

A491-11(2017): Standard Specification for Aluminum-Coated Steel Chain-Link Fence Fabric

A824-01(2017): Standard Specification for Metallic-Coated Steel Marcelled Tension Wire for Use With Chain Link Fence

D1666-17: Standard Test Methods for Conducting Machining Tests of Wood and Wood-Base Panel Materials

D7553-15: Standard Test Method for Solubility of Asphalt Materials in N-Propyl Bromide

D7741/D7741M-11(2017): Standard Test Method for Measurement of Apparent Viscosity of Asphalt-Rubber or Other Asphalt Binders by Using a Rotational Handheld Viscometer

E274/E274M-15: Standard Test Method for Skid Resistance of Paved Surfaces Using a Full-Scale Tire

E2259-03a(2011): Standard Guide for Archiving and Retrieving ITS-Generated Data

E2840-11(2015): Standard Practice for Pavement Condition Index Surveys for Interlocking Concrete Roads and Parking Lots

C1481-12(2017): Standard Guide for Use of Joint Sealants with Exterior Insulation and Finish Systems (EIFS)

D6857/D6857M-17: Standard Test Method for Maximum Specific Gravity and Density of Asphalt Mixtures Using Automatic Vacuum Sealing Method

C1523-17: Standard Test Method for Determining Modulus, Tear and Adhesion Properties of Precured Elastomeric Joint Sealants

D6752/D6752M-17: Standard Test Method for Bulk Specific Gravity and Density of Compacted Asphalt Mixtures Using Automatic Vacuum Sealing Method

C1246-17: Standard Test Method for Effects of Heat Aging on Weight Loss, Cracking, and Chalking of Elastomeric Sealants After Cure

D7032-17: Standard Specification for Establishing Performance Ratings for Wood-Plastic Composite and Plastic Lumber Deck Boards, Stair Treads, Guards, and Handrails

C542-05(2017): Standard Specification for Lock-Strip Gaskets

C736-12(2017): Standard Test Method for Extension-Recovery and Adhesion of Latex Sealants

C955-17: Standard Specification for Cold-Formed Steel Structural Framing Members

C963-00(2017): Standard Specification for Packaging, Identification, Shipment, and Storage of Lock-Strip Gaskets

D7000-11(2017): Standard Test Method for Sweep Test of Bituminous Emulsion Surface Treatment Samples

C1349-17: Standard Specification for Architectural Flat Glass Clad Polycarbonate

F1043-17a: Standard Specification for Strength and Protective Coatings on Steel Industrial Fence Framework

D7428-15: Standard Test Method for Resistance of Fine Aggregate to Degradation by Abrasion in the Micro-Deval Apparatus

D7495-12: Standard Specification for Minimum Requirements for Accreditation Bodies that Accredit Agencies Testing and Inspecting Road and Paving Materials

C1136-17: Standard Specification for Flexible, Low Permeance Vapor Retarders for Thermal Insulation

C969-17: Standard Practice for Infiltration and Exfiltration Acceptance Testing of Installed Precast Concrete Pipe Sewer Lines

C969M-17: Standard Practice for Infiltration and Exfiltration Acceptance Testing of Installed Precast Concrete Pipe Sewer Lines (Metric)

C1278/C1278M-17: Standard Specification for Fiber-Reinforced Gypsum Panel

C1600/C1600M-17: Standard Specification for Rapid Hardening Hydraulic Cement

C138/C138M-17a: Standard Test Method for Density (Unit Weight), Yield, and Air Content (Gravimetric) of Concrete

C142/C142M-17: Standard Test Method for Clay Lumps and Friable Particles in Aggregates

C1701/C1701M-17a: Standard Test Method for Infiltration Rate of In Place Pervious Concrete

C1749-17a: Standard Guide for Measurement of the Rheological Properties of Hydraulic Cementious Paste Using a Rotational Rheometer

C1768/C1768M-12(2017): Standard Practice for Accelerated Curing of Concrete Cylinders

C1373/C1373M-11(2017): Standard Practice for Determination of Thermal Resistance of Attic Insulation Systems Under Simulated Winter Conditions

C1589/C1589M-17b: Standard Practice for Outdoor Weathering of Construction Seals and Sealants

C843-17: Standard Specification for Application of Gypsum Veneer Plaster

C686-17: Standard Test Method for Parting Strength of Mineral Fiber Batt- and Blanket-Type Insulation

D1970/D1970M-17: Standard Specification for Self-Adhering Polymer Modified Bituminous Sheet Materials Used as Steep Roofing Underlayment for Ice Dam Protection

D6948/D6948M-03(2017): Standard Practice for Application of Refined Coal Tar (Ready to Use, Commercial Grade)

D5636/D5636M-94(2017): Standard Test Method for Low Temperature Unrolling of Felt or Sheet Roofing and Waterproofing Materials

D5683/D5683M-95(2017): Standard Test Method for Flexibility of Roofing and Waterproofing Materials and Membranes

D5727/D5727M-00(2017): Standard Specification for Emulsified Refined Coal Tar (Mineral Colloid Type)

D6382/D6382M-99(2017): Standard Practice for Dynamic Mechanical Analysis and Thermogravimetry of Roofing and Waterproofing Membrane Material

D6945/D6945M-03(2017): Standard Specification for Emulsified Refined Coal-Tar (Ready to Use, Commercial Grade)

E2150-17: Standard Classification for Life-Cycle Environmental Work Elements—Environmental Cost Element Structure

E2637-17: Standard Guide for Utilizing the Environmental Cost Element Structure Presented by Classification

C1729-17: Standard Specification for Aluminum Jacketing for Insulation

C1729M-17: Standard Specification for Aluminum Jacketing for Insulation

D4280-15: Standard Specification for Extended Life Type, Nonplowable, Raised Retroreflective Pavement Markers

D4792/D4792M-13: Standard Test Method for Potential Expansion of Aggregates from Hydration Reactions

D4866/D4866M-88(2017): Standard Performance Specification for Coal Tar Pitch Emulsion Pavement Sealer Mix Formulations Containing Mineral Aggregates and Optional Polymeric Admixtures

D5340-12: Standard Test Method for Airport Pavement Condition Index Surveys

D6373-16: Standard Specification for Performance Graded Asphalt Binder

D6433-16: Standard Practice for Roads and Parking Lots Pavement Condition Index Surveys

D6703-14: Standard Test Method for Automated Heithaus Titrimetry

D6932/D6932M-08(2013): Standard Guide for Materials and Construction of Open-Graded Friction Course Plant Mixtures

D7113/D7113M-10(2016): Standard Test Method for Density of Bituminous Paving Mixtures in Place by the Electromagnetic Surface Contact Methods

D7115-10(2015): Standard Test Method for Measurement of Superpave Gyratory Compactor (SGC) Internal Angle of Gyration Using Simulated Loading

D7175-15: Standard Test Method for Determining the Rheological Properties of Asphalt Binder Using a Dynamic Shear Rheometer

A416/A416M-17: Standard Specification for Low-Relaxation, Seven-Wire Steel Strand for Prestressed Concrete

C444-17: Standard Specification for Perforated Concrete Pipe

C444M-17: Standard Specification for Perforated Concrete Pipe (Metric)

C497-17: Standard Test Methods for Concrete Pipe, Manhole Sections, or Tile

C497M-17: Standard Test Methods for Concrete Pipe, Manhole Sections, or Tile (Metric)