All Energy & Utilities Standards

Search within Energy & Utilities


A1009-18: Standard Specification for Soft Magnetic MnZn Ferrite Core Materials for Transformer and Inductor Applications

A1012-10(2015): Standard Specification for Seamless and Welded Ferritic, Austenitic and Duplex Alloy Steel Condenser and Heat Exchanger Tubes With Integral Fins

A1013-00(2020): Standard Test Method for High-Frequency (10 kHz-1 MHz) Core Loss of Soft Magnetic Core Components at Controlled Temperatures Using the Voltmeter-Ammeter-Wattmeter Method

A1017/A1017M-17: Standard Specification for Pressure Vessel Plates, Alloy Steel, Chromium-Molybdenum-Tungsten

A1028-03(2015): Standard Specification for Stainless Steel Bars for Compressor and Turbine Airfoils

A1049/A1049M-18: Standard Specification for Stainless Steel Forgings, Ferritic/Austenitic (Duplex), for Pressure Vessels and Related Components

A105/A105M-18: Standard Specification for Carbon Steel Forgings for Piping Applications

A1082/A1082M-16: Standard Specification for High Strength Precipitation Hardening and Duplex Stainless Steel Bolting for Special Purpose Applications

A1098/A1098M-18: Standard Specification for Welded Austenitic, Ferritic, Martensitic and Duplex Stainless Steel Boiler, Superheater, Condenser, and Heat Exchanger Tubes with Textured Surface(s)

A1106/A1106M-17: Standard Specification for Pressure Vessel Plate, Alloy Steel, Austenitic High Manganese for Cryogenic Application

A178/A178M-19: Standard Specification for Electric-Resistance-Welded Carbon Steel and Carbon-Manganese Steel Boiler and Superheater Tubes

A179/A179M-19: Standard Specification for Seamless Cold-Drawn Low-Carbon Steel Heat-Exchanger and Condenser Tubes

A192/A192M-17: Standard Specification for Seamless Carbon Steel Boiler Tubes for High-Pressure Service

A20/A20M-19: Standard Specification for General Requirements for Steel Plates for Pressure Vessels

A203/A203M-17: Standard Specification for Pressure Vessel Plates, Alloy Steel, Nickel

A204/A204M-17: Standard Specification for Pressure Vessel Plates, Alloy Steel, Molybdenum

A209/A209M-03(2017): Standard Specification for Seamless Carbon-Molybdenum Alloy-Steel Boiler and Superheater Tubes

A210/A210M-19: Standard Specification for Seamless Medium-Carbon Steel Boiler and Superheater Tubes

A213/A213M-19a: Standard Specification for Seamless Ferritic and Austenitic Alloy-Steel Boiler, Superheater, and Heat-Exchanger Tubes

A214/A214M-19: Standard Specification for Electric-Resistance-Welded Carbon Steel Heat-Exchanger and Condenser Tubes

A217/A217M-20: Standard Specification for Steel Castings, Martensitic Stainless and Alloy, for Pressure-Containing Parts, Suitable for High-Temperature Service

A225/A225M-17: Standard Specification for Pressure Vessel Plates, Alloy Steel, Manganese-Vanadium-Nickel

A234/A234M-19: Standard Specification for Piping Fittings of Wrought Carbon Steel and Alloy Steel for Moderate and High Temperature Service

A240/A240M-20: Standard Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels and for General Applications

A249/A249M-18a: Standard Specification for Welded Austenitic Steel Boiler, Superheater, Heat-Exchanger, and Condenser Tubes

A263-12(2019): Standard Specification for Stainless Chromium Steel-Clad Plate

A266/A266M-18: Standard Specification for Carbon Steel Forgings for Pressure Vessel Components

A275/A275M-18: Standard Practice for Magnetic Particle Examination of Steel Forgings

A285/A285M-17: Standard Specification for Pressure Vessel Plates, Carbon Steel, Low- and Intermediate-Tensile Strength

A288-18: Standard Specification for Carbon and Alloy Steel Forgings for Magnetic Retaining Rings for Turbine Generators

A289/A289M-97(2018): Standard Specification for Alloy Steel Forgings for Nonmagnetic Retaining Rings for Generators

A290/A290M-16: Standard Specification for Carbon and Alloy Steel Forgings for Rings for Reduction Gears

A299/A299M-17: Standard Specification for Pressure Vessel Plates, Carbon Steel, Manganese-Silicon

A336/A336M-19: Standard Specification for Alloy Steel Forgings for Pressure and High-Temperature Parts

A341/A341M-16: Standard Test Method for Direct Current Magnetic Properties of Soft Magnetic Materials Using D-C Permeameters and the Point by Point (Ballistic) Test Methods

A343/A343M-14(2019): Standard Test Method for Alternating-Current Magnetic Properties of Materials at Power Frequencies Using Wattmeter-Ammeter-Voltmeter Method and 25-cm Epstein Test Frame

A345-19: Standard Specification for Flat-Rolled Electrical Steels for Magnetic Applications

A350/A350M-18: Standard Specification for Carbon and Low-Alloy Steel Forgings, Requiring Notch Toughness Testing for Piping Components

A351/A351M-18e1: Standard Specification for Castings, Austenitic, for Pressure-Containing Parts

A352/A352M-18a: Standard Specification for Steel Castings, Ferritic and Martensitic, for Pressure-Containing Parts, Suitable for Low-Temperature Service

A353/A353M-17: Standard Specification for Pressure Vessel Plates, Alloy Steel, Double-Normalized and Tempered 9 % Nickel

A356/A356M-16: Standard Specification for Steel Castings, Carbon, Low Alloy, and Stainless Steel, Heavy-Walled for Steam Turbines

A381/A381M-18: Standard Specification for Metal-Arc-Welded Carbon or High-Strength Low-Alloy Steel Pipe for Use With High-Pressure Transmission Systems

A387/A387M-17a: Standard Specification for Pressure Vessel Plates, Alloy Steel, Chromium-Molybdenum

A389/A389M-13(2018): Standard Specification for Steel Castings, Alloy, Specially Heat Treated, for Pressure-Containing Parts, Suitable for High-Temperature Service

A414/A414M-14(2019): Standard Specification for Steel, Sheet, Carbon, and High-Strength, Low-Alloy for Pressure Vessels

A418/A418M-15(2020): Standard Practice for Ultrasonic Examination of Turbine and Generator Steel Rotor Forgings

A420/A420M-20: Standard Specification for Piping Fittings of Wrought Carbon Steel and Alloy Steel for Low-Temperature Service

A437/A437M-15: Standard Specification for Stainless and Alloy-Steel Turbine-Type Bolting Specially Heat Treated for High-Temperature Service

A453/A453M-17: Standard Specification for High-Temperature Bolting, with Expansion Coefficients Comparable to Austenitic Stainless Steels

A469/A469M-07(2017): Standard Specification for Vacuum-Treated Steel Forgings for Generator Rotors

A470/A470M-05(2020): Standard Specification for Vacuum-Treated Carbon and Alloy Steel Forgings for Turbine Rotors and Shafts

A471/A471M-19: Standard Specification for Vacuum-Treated Alloy Steel Forgings for Turbine Rotor Disks and Wheels

A472/A472M-07(2017): Standard Specification for Heat Stability of Steam Turbine Shafts and Rotor Forgings

A498/A498M-17: Standard Specification for Seamless and Welded Carbon Steel Heat-Exchanger Tubes with Integral Fins

A508/A508M-18: Standard Specification for Quenched and Tempered Vacuum-Treated Carbon and Alloy Steel Forgings for Pressure Vessels

A515/A515M-17: Standard Specification for Pressure Vessel Plates, Carbon Steel, for Intermediate- and Higher-Temperature Service

A516/A516M-17: Standard Specification for Pressure Vessel Plates, Carbon Steel, for Moderate- and Lower-Temperature Service

A517/A517M-17: Standard Specification for Pressure Vessel Plates, Alloy Steel, High-Strength, Quenched and Tempered

A531/A531M-18: Standard Practice for Ultrasonic Examination of Turbine-Generator Steel Retaining Rings

A533/A533M-16: Standard Specification for Pressure Vessel Plates, Alloy Steel, Quenched and Tempered, Manganese-Molybdenum and Manganese-Molybdenum-Nickel

A537/A537M-20: Standard Specification for Pressure Vessel Plates, Heat-Treated, Carbon-Manganese-Silicon Steel

A541/A541M-05(2020): Standard Specification for Quenched and Tempered Carbon and Alloy Steel Forgings for Pressure Vessel Components

A542/A542M-19: Standard Specification for Pressure Vessel Plates, Alloy Steel, Quenched-and-Tempered, Chromium-Molybdenum, and Chromium-Molybdenum-Vanadium

A543/A543M-09(2014): Standard Specification for Pressure Vessel Plates, Alloy Steel, Quenched and Tempered Nickel-Chromium-Molybdenum

A553/A553M-17e1: Standard Specification for Pressure Vessel Plates, Alloy Steel, Quenched and Tempered 7, 8, and 9 % Nickel

A556/A556M-18: Standard Specification for Seamless Cold-Drawn Carbon Steel Feedwater Heater Tubes

A562/A562M-10(2015): Standard Specification for Pressure Vessel Plates, Carbon Steel, Manganese-Titanium for Glass or Diffused Metallic Coatings

A592/A592M-10(2020): Standard Specification for High-Strength Quenched and Tempered Low-Alloy Steel Forged Parts for Pressure Vessels

A596/A596M-14: Standard Test Method for Direct-Current Magnetic Properties of Materials Using the Ballistic Method and Ring Specimens

A598/A598M-02(2015): Standard Test Method for Magnetic Properties of Magnetic Amplifier Cores

A608/A608M-20: Standard Specification for Centrifugally Cast Iron-Chromium-Nickel High-Alloy Tubing for Pressure Application at High Temperatures

A612/A612M-20: Standard Specification for Pressure Vessel Plates, Carbon Steel, High Strength, for Moderate and Lower Temperature Service

A645/A645M-10(2016): Standard Specification for Pressure Vessel Plates, 5 % and 51 2 % Nickel Alloy Steels, Specially Heat Treated

A662/A662M-17: Standard Specification for Pressure Vessel Plates, Carbon-Manganese-Silicon Steel, for Moderate and Lower Temperature Service

A664-15: Standard Practice for Identification of Standard Electrical Steel Grades in ASTM Specifications

A688/A688M-18: Standard Specification for Seamless and Welded Austenitic Stainless Steel Feedwater Heater Tubes

A703/A703M-20: Standard Specification for Steel Castings, General Requirements, for Pressure-Containing Parts

A719/A719M-14(2019): Standard Test Method for Lamination Factor of Magnetic Materials

A723/A723M-18a: Standard Specification for Alloy Steel Forgings for High-Strength Pressure Component Application

A724/A724M-09(2018): Standard Specification for Pressure Vessel Plates, Carbon-Manganese-Silicon Steel, Quenched and Tempered, for Welded Pressure Vessels

A736/A736M-17: Standard Specification for Pressure Vessel Plates, Low-Carbon Age-Hardening Nickel-Copper-Chromium-Molybdenum-Columbium (Niobium) Alloy Steel

A737/A737M-17: Standard Specification for Pressure Vessel Plates, High-Strength, Low-Alloy Steel

A738/A738M-19: Standard Specification for Pressure Vessel Plates, Heat-Treated, Carbon-Manganese-Silicon Steel, for Moderate and Lower Temperature Service

A739-90a(2016): Standard Specification for Steel Bars, Alloy, Hot-Wrought, for Elevated Temperature or Pressure-Containing Parts, or Both

A757/A757M-15: Standard Specification for Steel Castings, Ferritic and Martensitic, for Pressure-Containing and Other Applications, for Low-Temperature Service

A803/A803M-16: Standard Specification for Seamless and Welded Ferritic Stainless Steel Feedwater Heater Tubes

A822/A822M-20: Standard Specification for Seamless Cold-Drawn Carbon Steel Tubing for Hydraulic System Service

A832/A832M-17: Standard Specification for Pressure Vessel Plates, Alloy Steel, Chromium-Molybdenum-Vanadium

A841/A841M-17: Standard Specification for Steel Plates for Pressure Vessels, Produced by Thermo-Mechanical Control Process (TMCP)

A844/A844M-09(2015): Standard Specification for Steel Plates, 9 %  Nickel Alloy, for Pressure Vessels, Produced by the Direct-Quenching Process

A858/A858M-19: Standard Specification for Heat-Treated Carbon Steel Fittings for Low-Temperature and Corrosive Service

A859/A859M-04(2019)e1: Standard Specification for Age-Hardening Alloy Steel Forgings for Pressure Vessel Components

A867-19: Standard Specification for Iron-Silicon Relay Steels

A887-20: Standard Specification for Borated Stainless Steel Plate, Sheet, and Strip for Nuclear Application

A889/A889M-14(2020): Standard Test Method for Alternating-Current Magnetic Properties of Materials at Low Magnetic Flux Density Using the Voltmeter-Ammeter-Wattmeter-Varmeter Method and 25-cm Epstein Frame

A891/A891M-16: Standard Specification for Precipitation Hardening Iron Base Superalloy Forgings for Turbine Rotor Disks and Wheels

A905-19: Standard Specification for Steel Wire, Pressure Vessel Winding

A965/A965M-20: Standard Specification for Steel Forgings, Austenitic, for Pressure and High Temperature Parts

A982/A982M-10(2020): Standard Specification for Steel Forgings, Stainless, for Compressor and Turbine Airfoils

A985/A985M-20: Standard Specification for Steel Investment Castings General Requirements, for Pressure-Containing Parts

A990/A990M-18: Standard Specification for Castings, Iron-Nickel-Chromium and Nickel Alloys, Specially Controlled for Pressure-Retaining Parts for Corrosive Service

B1-13(2018): Standard Specification for Hard-Drawn Copper Wire

B1004-16: Standard Practice for Contact Performance Classification of Electrical Connection Systems

B1005-17: Standard Specification for Copper-Clad Aluminum Bar for Electrical Purposes (Bus Bar)

B1006-17: Standard Specification for Electrical Overhead Conductor Code Word Names

B1008-18: Standard Test Method for Stress-Strain Testing for Overhead Electrical Conductors

B105-05(2020): Standard Specification for Hard-Drawn Copper Alloy Wires for Electric Conductors

B163-19: Standard Specification for Seamless Nickel and Nickel Alloy Condenser and Heat-Exchanger Tubes

B171/B171M-18: Standard Specification for Copper-Alloy Plate and Sheet for Pressure Vessels, Condensers, and Heat Exchangers

B189-05(2015): Standard Specification for Lead-Coated and Lead-Alloy-Coated Soft Copper Wire for Electrical Purposes

B193-19: Standard Test Method for Resistivity of Electrical Conductor Materials

B2-13(2018): Standard Specification for Medium-Hard-Drawn Copper Wire

B226-11(2016): Standard Specification for Cored, Annular, Concentric-Lay-Stranded Copper Conductors

B227-15(2019): Standard Specification for Hard-Drawn Copper-Clad Steel Wire

B228-11a(2016): Standard Specification for Concentric-Lay-Stranded Copper-Clad Steel Conductors

B230/B230M-07(2016): Standard Specification for Aluminum 1350–H19 Wire for Electrical Purposes

B233-97(2016): Standard Specification for Aluminum 1350 Drawing Stock for Electrical Purposes

B234-17: Standard Specification for Aluminum and Aluminum-Alloy Drawn Seamless Tubes for Surface Condensers, Evaporators, and Heat Exchangers

B234M-17: Standard Specification for Aluminum and Aluminum-Alloy Drawn Seamless Tubes for Surface Condensers, Evaporators, and Heat Exchangers (Metric)

B236-07(2015): Standard Specification for Aluminum Bars for Electrical Purposes (Bus Bars)

B236M-07(2015): Standard Specification for Aluminum Bars for Electrical Purposes (Bus Bars) (Metric)

B246-15: Standard Specification for Tinned Hard-Drawn and Medium-Hard-Drawn Copper Wire for Electrical Purposes

B258-18: Standard Specification for Standard Nominal Diameters and Cross-Sectional Areas of AWG Sizes of Solid Round Wires Used as Electrical Conductors

B263/B263M-14(2020): Standard Test Method for Determination of Cross-Sectional Area of Stranded Conductors

B279-13(2019): Standard Test Method for Stiffness of Bare Soft Square and Rectangular Copper and Aluminum Wire for Magnet Wire Fabrication

B286-07(2017): Standard Specification for Copper Conductors for Use in Hookup Wire for Electronic Equipment

B3-13(2018): Standard Specification for Soft or Annealed Copper Wire

B33-10(2020)e1: Standard Specification for Tin-Coated Soft or Annealed Copper Wire for Electrical Purposes

B338-17e1: Standard Specification for Seamless and Welded Titanium and Titanium Alloy Tubes for Condensers and Heat Exchangers

B349/B349M-16: Standard Specification for Zirconium Sponge and Other Forms of Virgin Metal for Nuclear Application

B350/B350M-11(2016)e1: Standard Specification for Zirconium and Zirconium Alloy Ingots for Nuclear Application

B351/B351M-13(2018): Standard Specification for Hot-Rolled and Cold-Finished Zirconium and Zirconium Alloy Bars, Rod, and Wire for Nuclear Application

B352/B352M-17: Standard Specification for Zirconium and Zirconium Alloy Sheet, Strip, and Plate for Nuclear Application

B353-12(2017): Standard Specification for Wrought Zirconium and Zirconium Alloy Seamless and Welded Tubes for Nuclear Service (Except Nuclear Fuel Cladding)

B355-11(2016): Standard Specification for Nickel-Coated Soft or Annealed Copper Wire

B359/B359M-18: Standard Specification for Copper and Copper-Alloy Seamless Condenser and Heat Exchanger Tubes With Integral Fins

B373-19: Standard Specification for Aluminum Foil for Capacitors

B395/B395M-18: Standard Specification for U-Bend Seamless Copper and Copper Alloy Heat Exchanger and Condenser Tubes

B398/B398M-15: Standard Specification for Aluminum-Alloy 6201-T81 and 6201-T83 Wire for Electrical Purposes

B399/B399M-04(2015): Standard Specification for Concentric-Lay-Stranded Aluminum-Alloy 6201-T81 Conductors

B400/B400M-19: Standard Specification for Compact Round Concentric-Lay-Stranded Aluminum 1350 Conductors

B401-12(2016): Standard Specification for Compact Round Concentric-Lay-Stranded Aluminum Conductors, Steel-Reinforced (ACSR/COMP)

B415-16: Standard Specification for Hard-Drawn Aluminum-Clad Steel Wire

B416-98(2018): Standard Specification for Concentric-Lay-Stranded Aluminum-Clad Steel Conductors

B470-02(2017): Standard Specification for Bonded Copper Conductors for Use in Hookup Wires for Electronic Equipment

B496-16: Standard Specification for Compact Round Concentric-Lay-Stranded Copper Conductors

B498/B498M-19: Standard Specification for Zinc-Coated (Galvanized) Steel Core Wire for Use in Overhead Electrical Conductors

B500/B500M-12(2018): Standard Specification for Metallic Coated or Aluminum Clad Stranded Steel Core for Use in Overhead Electrical Conductors

B524/B524M-18: Standard Specification for Concentric-Lay-Stranded Aluminum Conductors, Aluminum-Alloy Reinforced (ACAR, 1350/6201)

B539-20: Standard Test Methods for Measuring Resistance of Electrical Connections (Static Contacts)

B543/B543M-18: Standard Specification for Welded Copper and Copper-Alloy Heat Exchanger Tube

B548-03(2017): Standard Test Method for Ultrasonic Inspection of Aluminum-Alloy Plate for Pressure Vessels

B549-18: Standard Specification for Concentric-Lay-Stranded Aluminum Conductors, Aluminum-Clad Steel Reinforced for Use in Overhead Electrical Conductors

B566-04a(2016): Standard Specification for Copper-Clad Aluminum Wire

B569-19: Standard Specification for Brass Strip in Narrow Widths and Light Gage for Heat-Exchanger Tubing

B603-07(2018): Standard Specification for Drawn or Rolled Iron-Chromium-Aluminum Alloys for Electrical Heating Elements

B606/B606M-19: Standard Specification for High-Strength Zinc-Coated (Galvanized) Steel Core Wire for Aluminum and Aluminum-Alloy Conductors, Steel Reinforced

B682-01(2016): Standard Specification for Standard Metric Sizes of Electrical Conductors

B694-19: Standard Specification for Copper, Copper-Alloy, Copper-Clad Bronze (CCB), Copper-Clad Stainless Steel (CCS), and Copper-Clad Alloy Steel (CAS) Sheet and Strip for Electrical Cable Shielding

B70-90(2019): Standard Test Method for Change of Resistance With Temperature of Metallic Materials for Electrical Heating

B701/B701M-13(2018): Standard Specification for Concentric-Lay-Stranded Self-Damping Aluminum Conductors, Steel Reinforced (ACSR/SD)

B711-18: Standard Specification for Concentric-Lay-Stranded Aluminum-Alloy Conductors, Steel Reinforced (AACSR) (6201)

B738-13(2018): Standard Specification for Fine-Wire Bunch-Stranded and Rope-Lay Bunch-Stranded Copper Conductors for Use as Electrical Conductors

B76-90(2018): Standard Test Method for Accelerated Life of Nickel-Chromium and Nickel-Chromium-Iron Alloys for Electrical Heating

B77-07(2018): Standard Test Method for Thermoelectric Power of Electrical-Resistance Alloys

B778-19: Standard Specification for Shaped Wire Compact Concentric-Lay-Stranded Aluminum Conductors (AAC/TW)

B779-18: Standard Specification for Shaped Wire Compact Concentric-Lay-Stranded Aluminum Conductors, Steel-Reinforced (ACSR/TW)

B784-01(2017)e1: Standard Specification for Modified Concentric-Lay-Stranded Copper Conductors for Use in Insulated Electrical Cables

B786/B786M-08(2018): Standard Specification for 19 Wire Combination Unilay-Stranded Aluminum Conductors for Subsequent Insulation

B787/B787M-04(2020): Standard Specification for 19 Wire Combination Unilay-Stranded Copper Conductors for Subsequent Insulation

B8-11(2017): Standard Specification for Concentric-Lay-Stranded Copper Conductors, Hard, Medium-Hard, or Soft

B800-05(2015): Standard Specification for 8000 Series Aluminum Alloy Wire for Electrical Purposes—Annealed and Intermediate Tempers

B801-18: Standard Specification for Concentric-Lay-Stranded Conductors of 8000 Series Aluminum Alloy for Subsequent Covering or Insulation

B802/B802M-19: Standard Specification for Zinc–5 % Aluminum-Mischmetal Alloy-Coated Steel Core Wire for Aluminum Conductors, Steel Reinforced (ACSR)

B803/B803M-19: Standard Specification for High-Strength Zinc–5 % Aluminum-Mischmetal Alloy-Coated Steel Core Wire for Use in Overhead Electrical Conductors

B830-18: Standard Specification for Uniform Test Methods and Frequency

B835-14(2020): Standard Specification for Compact Round Stranded Copper Conductors Using Single Input Wire Construction

B836-00(2015): Standard Specification for Compact Round Stranded Aluminum Conductors Using Single Input Wire Construction

B856-18: Standard Specification for Concentric-Lay-Stranded Aluminum Conductors, Coated Steel Supported (ACSS)

B857-18: Standard Specification for Shaped Wire Compact Concentric-Lay-Stranded Aluminum Conductors, Coated-Steel Supported (ACSS/TW)

B869-07(2018): Standard Specification for Copper-Clad Steel Electrical Conductor for CATV Drop Wire

B901-04(2015): Standard Specification for Compressed Round Stranded Aluminum Conductors Using Single Input Wire Construction

B902/B902M-13(2018): Standard Specification for Compressed Round Stranded Copper Conductors, Hard, Medium-Hard, or Soft Using Single Input Wire Construction

B903-15: Standard Specification for Seamless Copper Heat Exchanger Tubes With Internal Enhancement

B910/B910M-07(2018): Standard Specification for Annealed Copper-Clad Steel Wire

B919-19: Standard Specification for Welded Copper Heat Exchanger Tubes With Internal Enhancement

B941-16: Standard Specification for Heat Resistant Aluminum-Zirconium Alloy Wire for Electrical Purposes

B944-11(2016): Standard Specification for Copper-Beryllium Welded Heat Exchanger and Condenser Tube (UNS No. C17510)

B956-19e1: Standard Specification for Welded Copper and Copper-Alloy Condenser and Heat Exchanger Tubes with Integral Fins

B958/B958M-19: Standard Specification for Extra-High-Strength and Ultra-High-Strength Class A Zinc–5% Aluminum-Mischmetal Alloy-Coated Steel Core Wire for Use in Overhead Electrical Conductors

B96/B96M-20: Standard Specification for Copper-Silicon Alloy Plate, Sheet, Strip, and Rolled Bar for General Purposes and Pressure Vessels

B961-13(2019): Standard Specification for Silver Coated Copper and Copper Alloy Stranded Conductors for Electronic Space Application

B965-09(2018): Standard Specification for High Performance Tin-Coated Annealed Copper Wire Intended for Electrical and Electronic Application for Solderability

B971-10(2020)e1: Standard Specification for Silver-Coated Braid and Ribbon Flat Copper Wire intended for use in Electronic Application

B972-10(2020)e1: Standard Specification for Nickel-Coated Braid and Ribbon Flat Copper Wire Intended for use in Electronic Application

B973-10(2020)e1: Standard Specification for Tin-Coated Braid and Ribbon Flat Copper Wire intended for use in Electronic Application

B976-11(2015): Standard Specification for Fiber Reinforced Aluminum Matrix Composite (AMC) Core Wire for Aluminum Conductors, Composite Reinforced (ACCR)

B979-12(2018): Standard Specification for Non-Specular (NS) Surface Finish on Overhead Aluminum Electrical Conductors

B986-13(2019): Standard Test Method for Determination of Tensile Strength by Mass Method for Stranded Conductors Intended for use in Electronic Application

C1000-19: Standard Test Method for Radiochemical Determination of Uranium Isotopes in Soil by Alpha Spectrometry

C1001-19: Standard Test Method for Radiochemical Determination of Plutonium in Soil by Alpha Spectroscopy

C1009-13a: Standard Guide for Establishing and Maintaining a Quality Assurance Program for Analytical Laboratories Within the Nuclear Industry

C1030-10(2018): Standard Test Method for Determination of Plutonium Isotopic Composition by Gamma-Ray Spectrometry

C1031-11(2016): Standard Specification for Nuclear-Grade Aluminum Oxide Powder

C1052-20: Standard Practice for Bulk Sampling of Liquid Uranium Hexafluoride

C1062-00(2014): Standard Guide for Design, Fabrication, and Installation of Nuclear Fuel Dissolution Facilities

C1065-08(2015): Standard Specification for Nuclear-Grade Zirconium Oxide Powder

C1066-09(2015): Standard Specification for Nuclear Grade Zirconium Oxide Pellets

C1068-15: Standard Guide for Qualification of Measurement Methods by a Laboratory Within the Nuclear Industry

C1076-09(2015): Standard Specification for Nuclear Grade Hafnium Oxide Pellets

C1098-08(2015): Standard Specification for Nuclear-Grade Hafnium Oxide Powder

C1109-10(2015): Standard Practice for Analysis of Aqueous Leachates from Nuclear Waste Materials Using Inductively Coupled Plasma-Atomic Emission Spectroscopy

C1111-10(2015): Standard Test Method for Determining Elements in Waste Streams by Inductively Coupled Plasma-Atomic Emission Spectroscopy

C1128-18: Standard Guide for Preparation of Working Reference Materials for Use in Analysis of Nuclear Fuel Cycle Materials

C1133/C1133M-10(2018): Standard Test Method for Nondestructive Assay of Special Nuclear Material in Low-Density Scrap and Waste by Segmented Passive Gamma-Ray Scanning

C1156-18: Standard Guide for Establishing Calibration for a Measurement Method Used to Analyze Nuclear Fuel Cycle Materials

C1163-14: Standard Practice for Mounting Actinides for Alpha Spectrometry Using Neodymium Fluoride

C1168-15: Standard Practice for Preparation and Dissolution of Plutonium Materials for Analysis

C1169-97(2012): Standard Guide for Laboratory Evaluation of Automatic Pedestrian SNM Monitor Performance

C1187-20a: Standard Guide for Establishing Surveillance Test Program for Boron-based Neutron Absorbing Material Systems for Use in Nuclear Fuel Storage Racks in Pool Environment

C1189-11(2018): Standard Guide to Procedures for Calibrating Automatic Pedestrian SNM Monitors

C1204-14: Standard Test Method for Uranium in Presence of Plutonium by Iron(II) Reduction in Phosphoric Acid Followed by Chromium(VI) Titration

C1205-07(2012): Standard Test Method for The Radiochemical Determination of Americium-241 in Soil by Alpha Spectrometry

C1207-10(2018): Standard Test Method for Nondestructive Assay of Plutonium in Scrap and Waste by Passive Neutron Coincidence Counting

C1210-18: Standard Guide for Establishing a Measurement System Quality Control Program for Analytical Chemistry Laboratories Within the Nuclear Industry

C1215-18: Standard Guide for Preparing and Interpreting Precision and Bias Statements in Test Method Standards Used in the Nuclear Industry

C1217-00(2020): Standard Guide for Design of Equipment for Processing Nuclear and Radioactive Materials

C1221-10(2018): Standard Test Method for Nondestructive Analysis of Special Nuclear Materials in Homogeneous Solutions by Gamma-Ray Spectrometry

C1233-15: Standard Practice for Determining Equivalent Boron Contents of Nuclear Materials

C1238-97(2012): Standard Guide for Installation of Walk-Through Metal Detectors

C125-20: Standard Terminology Relating to Concrete and Concrete Aggregates

C1254-18: Standard Test Method for Determination of Uranium in Mineral Acids by X-Ray Fluorescence

C1255-18: Standard Test Method for Analysis of Uranium and Thorium in Soils by Energy Dispersive X-Ray Fluorescence Spectroscopy

C1268-15: Standard Test Method for Quantitative Determination of 241Am in Plutonium by Gamma-Ray Spectrometry

C1269-97(2012): Standard Practice for Adjusting the Operational Sensitivity Setting of In-Plant Walk-Through Metal Detectors

C1270-97(2012): Standard Practice for Detection Sensitivity Mapping of In-Plant Walk-Through Metal Detectors

C1284-18: Standard Practice for Electrodeposition of the Actinides for Alpha Spectrometry

C1285-14: Standard Test Methods for Determining Chemical Durability of Nuclear, Hazardous, and Mixed Waste Glasses and Multiphase Glass Ceramics: The Product Consistency Test (PCT)

C1287-18: Standard Test Method for Determination of Impurities in Nuclear Grade Uranium Compounds by Inductively Coupled Plasma Mass Spectrometry

C1295-15: Standard Test Method for Gamma Energy Emission from Fission and Decay Products in Uranium Hexafluoride and Uranyl Nitrate Solution

C1297-18: Standard Guide for Qualification of Laboratory Analysts for the Analysis of Nuclear Fuel Cycle Materials

C1307-15: Standard Test Method for Plutonium Assay by Plutonium (III) Diode Array Spectrophotometry

C1309-97(2012): Standard Practice for Performance Evaluation of In-Plant Walk-Through Metal Detectors

C1334-05(2016)e1: Standard Specification for Uranium Oxides with a 235U Content of Less Than 5 % for Dissolution Prior to Conversion to Nuclear-Grade Uranium Dioxide

C1343-16: Standard Test Method for Determination of Low Concentrations of Uranium in Oils and Organic Liquids by X-ray Fluorescence

C1346-19: Standard Practice for Dissolution of UF6 from P-10 Tubes

C1347-08(2014)e1: Standard Practice for Preparation and Dissolution of Uranium Materials for Analysis

C1387-14: Standard Guide for the Determination of Technetium-99 in Soil

C1402-17: Standard Guide for High-Resolution Gamma-Ray Spectrometry of Soil Samples

C1408-16: Standard Test Method for Carbon (Total) in Uranium Oxide Powders and Pellets By Direct Combustion-Infrared Detection Method

C1411-20: Standard Practice for The Ion Exchange Separation of Uranium and Plutonium Prior to Isotopic Analysis

C1413-18: Standard Test Method for Isotopic Analysis of Hydrolyzed Uranium Hexafluoride and Uranyl Nitrate Solutions by Thermal Ionization Mass Spectrometry

C1415-18: Standard Test Method for 238Pu Isotopic Abundance By Alpha Spectrometry

C1428-18: Standard Test Method for Isotopic Analysis of Uranium Hexafluoride by Single–Standard Gas Source Multiple Collector Mass Spectrometer Method

C1429-99(2014): Standard Test Method for Isotopic Analysis of Uranium Hexafluoride by Double-Standard Multi-Collector Gas Mass Spectrometer

C1430-18: Standard Test Method for Determination of Uranium, Oxygen to Uranium (O/U), and Oxygen to Metal (O/M) in Sintered Uranium Dioxide and Gadolinia-Uranium Dioxide Pellets by Atmospheric Equilibration

C1431-99(2018): Standard Guide for Corrosion Testing of Aluminum-Based Spent Nuclear Fuel in Support of Repository Disposal

C1432-15: Standard Test Method for Determination of Impurities in Plutonium: Acid Dissolution, Ion Exchange Matrix Separation, and Inductively Coupled Plasma-Atomic Emission Spectroscopic (ICP/AES) Analysis

C1441-13: Standard Test Method for the Analysis of Refrigerant 114, Plus Other Carbon-Containing and Fluorine-Containing Compounds in Uranium Hexafluoride via Fourier-Transform Infrared (FTIR) Spectroscopy

C1453-19: Standard Test Method for the Determination of Uranium by Ignition and the Oxygen to Uranium (O/U) Atomic Ratio of Nuclear Grade Uranium Dioxide Powders and Pellets

C1455-14e1: Standard Test Method for Nondestructive Assay of Special Nuclear Material Holdup Using Gamma-Ray Spectroscopic Methods

C1456-13(2018): Standard Test Method for Determination of Uranium or Gadolinium (or both) in Gadolinium Oxide-Uranium Oxide Pellets or by X-Ray Fluorescence (XRF)

C1457-18: Standard Test Method for Determination of Total Hydrogen Content of Uranium Oxide Powders and Pellets by Carrier Gas Extraction

C1458-16: Standard Test Method for Nondestructive Assay of Plutonium, Tritium and 241Am by Calorimetric Assay

C1462-00(2013): Standard Specification for Uranium Metal Enriched to More than 15 % and Less Than 20 % 235U

C1463-19: Standard Practices for Dissolving Glass Containing Radioactive and Mixed Waste for Chemical and Radiochemical Analysis

C1473-19: Standard Test Method for Radiochemical Determination of Uranium Isotopes in Urine by Alpha Spectrometry

C1474-19: Standard Test Method for Analysis of Isotopic Composition of Uranium in Nuclear-Grade Fuel Material by Quadrupole Inductively Coupled Plasma-Mass Spectrometry

C1477-19: Standard Test Method for Isotopic Abundance Analysis of Uranium Hexafluoride and Uranyl Nitrate Solutions by Multi-Collector, Inductively Coupled Plasma-Mass Spectrometry

C1490-14: Standard Guide for the Selection, Training and Qualification of Nondestructive Assay (NDA) Personnel

C1493-19: Standard Test Method for Non-Destructive Assay of Nuclear Material in Waste by Passive and Active Neutron Counting Using a Differential Die-Away System

C1502-16: Standard Test Method for Determination of Total Chlorine and Fluorine in Uranium Dioxide and Gadolinium Oxide

C1507-12: Standard Test Method for Radiochemical Determination of Strontium-90 in Soil

C1508-18: Standard Test Method for Determination of Bromine and Chlorine in UF6 and Uranyl Nitrate by X-Ray Fluorescence (XRF) Spectroscopy

C1514-08(2017): Standard Test Method for Measurement of 235U Fraction Using Enrichment Meter Principle

C1517-16: Standard Test Method for Determination of Metallic Impurities in Uranium Metal or Compounds by DC-Arc Emission Spectroscopy

C1533-15: Standard Guide for General Design Considerations for Hot Cell Equipment

C1539-08(2014): Standard Test Method for Determination of Technetium-99 in Uranium Hexafluoride by Liquid Scintillation Counting

C1553-16: Standard Guide for Drying Behavior of Spent Nuclear Fuel

C1554-18: Standard Guide for Materials Handling Equipment for Hot Cells

C1561-10(2016): Standard Guide for Determination of Plutonium and Neptunium in Uranium Hexafluoride and U-Rich Matrix by Alpha Spectrometry

C1562-10(2018): Standard Guide for Evaluation of Materials Used in Extended Service of Interim Spent Nuclear Fuel Dry Storage Systems

C157/C157M-17: Standard Test Method for Length Change of Hardened Hydraulic-Cement Mortar and Concrete

C1572/C1572M-18: Standard Guide for Dry Lead Glass and Oil-Filled Lead Glass Radiation Shielding Window Components for Remotely Operated Facilities

C1590-04(2014): Standard Practice for Alternate Actinide Calibration for Inductively Coupled Plasma-Mass Spectrometry

C1615/C1615M-17: Standard Guide for Mechanical Drive Systems for Remote Operation in Hot Cell Facilities

C1625-19: Standard Test Method for Uranium and Plutonium Concentrations and Isotopic Abundances by Thermal Ionization Mass Spectrometry

C1636-13: Standard Guide for the Determination of Uranium-232 in Uranium Hexafluoride

C1637-13: Standard Test Method for the Determination of Impurities in Plutonium Metal: Acid Digestion and Inductively Coupled Plasma-Mass Spectroscopy (ICP-MS) Analysis

C1638-06(2013): Standard Guide for the Determination of Iodine-129 In Uranium Oxide

C1647-13: Standard Practice for Removal of Uranium or Plutonium, or both, for Impurity Assay in Uranium or Plutonium Materials

C1661-18: Standard Guide for Viewing Systems for Remotely Operated Facilities

C1662-18: Standard Practice for Measurement of the Glass Dissolution Rate Using the Single-Pass Flow-Through Test Method

C1671-20a: Standard Practice for Qualification and Acceptance of Boron Based Metallic Neutron Absorbers for Nuclear Criticality Control for Dry Cask Storage Systems and Transportation Packaging

C1672-17: Standard Test Method for Determination of Uranium or Plutonium Isotopic Composition or Concentration by the Total Evaporation Method Using a Thermal Ionization Mass Spectrometer

C1673-10a(2018): Standard Terminology of C26.10 Nondestructive Assay Methods

C1682-17: Standard Guide for Characterization of Spent Nuclear Fuel in Support of Interim Storage, Transportation and Geologic Repository Disposal

C1689-08a(2014): Standard Practice for Subsampling of Uranium Hexafluoride

C1718-10(2019): Standard Test Method for Nondestructive Assay of Radioactive Material by Tomographic Gamma Scanning

C1725-17: Standard Guide for Hot Cell Specialized Support Equipment and Tools

C1726/C1726M-10(2018): Standard Guide for Use of Modeling for Passive Gamma Measurements

C1742-17: Standard Test Method for Isotopic Analysis of Uranium Hexafluoride by Double Standard Single-Collector Gas Mass Spectrometer Method

C1751-20: Standard Guide for Sampling Radioactive Tank Waste

C1752-17: Standard Guide for Measuring Physical and Rheological Properties of Radioactive Solutions, Slurries, and Sludges

C1769-15: Standard Practice for Analysis of Spent Nuclear Fuel to Determine Selected Isotopes and Estimate Fuel Burnup

C1770-13: Standard Test Method for Determination of Loose and Tapped Bulk Density of Plutonium Oxide

C1771-19: Standard Test Method for Determination of Boron, Silicon, and Technetium in Hydrolyzed Uranium Hexafluoride by Inductively Coupled Plasma—Mass Spectrometer After Removal of Uranium by Solid Phase Extraction

C1783-15: Standard Guide for Development of Specifications for Fiber Reinforced Carbon-Carbon Composite Structures for Nuclear Applications

C1784-20: Standard Test Method for Using a Heat Flow Meter Apparatus for Measuring Thermal Storage Properties of Phase Change Materials and Products

C1793-15: Standard Guide for Development of Specifications for Fiber Reinforced Silicon Carbide-Silicon Carbide Composite Structures for Nuclear Applications

C1807-15: Standard Guide for Nondestructive Assay of Special Nuclear Material (SNM) Holdup Using Passive Neutron Measurement Methods

C1816-16: Standard Practice for The Ion Exchange Separation of Small Volume Samples Containing Uranium, Americium, and Plutonium Prior to Isotopic Abundance and Content Analysis

C1817-16: Standard Test Method for The Determination of the Oxygen to Metal (O/M) Ratio in Sintered Mixed Oxide ((U, Pu)O2) Pellets by Gravimetry

C1831/C1831M-17: Standard Guide for Gamma Radiation Shielding Performance Testing

C1838-16: Standard Practice for Cleaning for 1S and 2S Bottles

C1844-16: Standard Test Method for Determination of Uranium in Urine by Inductively Coupled Plasma Mass Spectrometer Following Nitric Acid Dilution

C1845-16: Standard Practice for The Separation of Lanthanide Elements from Uranium Matrices Using High Pressure Ion Chromatography (HPIC) for Isotopic Analyses by Inductively Coupled Plasma Mass Spectrometry (ICP-MS)

C1853-17: Standard Test Method for The Determination of Carbon (Total) Content in Mixed Oxide ((U, Pu)O2) Sintered Pellets by Direct Combustion-Infrared Detection Method

C1854-17: Standard Test Method for Determination of Hydrogen (total from all sources) in Mixed Oxide ((U, Pu)O2) Sintered Pellets by the Inert Gas Fusion Technique Followed by Thermal Conductivity Measurement

C1868-18: Standard Practice for Ceramographic Preparation of UO2 and Mixed Oxide (U,Pu)O2 Pellets for Microstructural Analysis

C696-19: Standard Test Methods for Chemical, Mass Spectrometric, and Spectrochemical Analysis of Nuclear-Grade Uranium Dioxide Powders and Pellets

C708-16: Standard Specification for Nuclear-Grade Beryllium Oxide Powder

C750-18: Standard Specification for Nuclear-Grade Boron Carbide Powder

C751-20: Standard Specification for Nuclear-Grade Boron Carbide Pellets

C752-18: Standard Specification for Nuclear-Grade Silver-Indium-Cadmium Alloy

C753-16a: Standard Specification for Nuclear-Grade, Sinterable Uranium Dioxide Powder

C757-16e1: Standard Specification for Nuclear-Grade Plutonium Dioxide Powder for Light Water Reactors

C758-18: Standard Test Methods for Chemical, Mass Spectrometric, Spectrochemical, Nuclear, and Radiochemical Analysis of Nuclear-Grade Plutonium Metal

C759-18: Standard Test Methods for Chemical, Mass Spectrometric, Spectrochemical, Nuclear, and Radiochemical Analysis of Nuclear-Grade Plutonium Nitrate Solutions

C760-90(2020): Standard Test Methods for Chemical and Spectrochemical Analysis of Nuclear-Grade Silver-Indium-Cadmium Alloys

C781-20: Standard Practice for Testing Graphite Materials for Gas-Cooled Nuclear Reactor Components

C784-20: Standard Specification for Nuclear-Grade Aluminum Oxide-Boron Carbide Composite Pellets

C785-08(2015): Standard Specification for Nuclear-Grade Aluminum Oxide Pellets

C787-20: Standard Specification for Uranium Hexafluoride for Enrichment

C788-03(2015): Standard Specification for Nuclear-Grade Uranyl Nitrate Solution or Crystals

C791-19: Standard Test Methods for Chemical, Mass Spectrometric, and Spectrochemical Analysis of Nuclear-Grade Boron Carbide

C799-19: Standard Test Methods for Chemical, Mass Spectrometric, Spectrochemical, Nuclear, and Radiochemical Analysis of Nuclear-Grade Uranyl Nitrate Solutions

C809-19: Standard Test Methods for Chemical, Mass Spectrometric, and Spectrochemical Analysis of Nuclear-Grade Aluminum Oxide and AluminumOxide-Boron Carbide Composite Pellets

C833-17: Standard Specification for Sintered (Uranium-Plutonium) Dioxide Pellets for Light Water Reactors

C852/C852M-17: Standard Guide for Design Criteria for Plutonium Gloveboxes

C859-14b: Standard Terminology Relating to Nuclear Materials

C888-18: Standard Specification for Nuclear-Grade Gadolinium Oxide (Gd2O3) Powder

C889-18: Standard Test Methods for Chemical and Mass Spectrometric Analysis of Nuclear-Grade Gadolinium Oxide (Gd2O3) Powder

C922-14: Standard Specification for Sintered Gadolinium Oxide-Uranium Dioxide Pellets

C967-20: Standard Specification for Uranium Ore Concentrate

C968-19: Standard Test Methods for Analysis of Sintered Gadolinium Oxide-Uranium Dioxide Pellets

C99/C99M-18: Standard Test Method for Modulus of Rupture of Dimension Stone

C992-20a: Standard Specification for Boron-based Neutron Absorbing Material Systems for Use in Nuclear Fuel Storage Racks in Pool Environment

C993-97(2012): Standard Guide for In-Plant Performance Evaluation of Automatic Pedestrian SNM Monitors

C996-20: Standard Specification for Uranium Hexafluoride Enriched to Less Than 5 %  235U

C998-17: Standard Practice for Sampling Surface Soil for Radionuclides

C999-17: Standard Practice for Soil Sample Preparation for the Determination of Radionuclides

D1169-19a: Standard Test Method for Specific Resistance (Resistivity) of Electrical Insulating Liquids

D117-18: Standard Guide for Sampling, Test Methods, and Specifications for Electrical Insulating Liquids

D121-15: Standard Terminology of Coal and Coke

D1275-15: Standard Test Method for Corrosive Sulfur in Electrical Insulating Liquids

D1304-99(2020)e1: Standard Test Methods for Adhesives Relative to Their Use as Electrical Insulation

D1412/D1412M-20: Standard Test Method for Equilibrium Moisture of Coal at 96 to 97 Percent Relative Humidity and 30 °C

D149-20: Standard Test Method for Dielectric Breakdown Voltage and Dielectric Strength of Solid Electrical Insulating Materials at Commercial Power Frequencies

D1524-15: Standard Test Method for Visual Examination of Used Electrical Insulating Liquids in the Field

D1533-12: Standard Test Method for Water in Insulating Liquids by Coulometric Karl Fischer Titration

D1534-95(2017): Standard Test Method for Approximate Acidity in Electrical Insulating Liquids by Color-Indicator Titration

D1675-18: Standard Test Methods for Polytetrafluoroethylene Tubing

D1711-20: Standard Terminology Relating to Electrical Insulation

D1816-12(2019): Standard Test Method for Dielectric Breakdown Voltage of Insulating Liquids Using VDE Electrodes

D1822-13: Standard Test Method for Tensile-Impact Energy to Break Plastics and Electrical Insulating Materials

D1868-20: Standard Test Method for Detection and Measurement of Partial Discharge (Corona) Pulses in Evaluation of Insulation Systems

D1903-08(2017): Standard Practice for Determining the Coefficient of Thermal Expansion of Electrical Insulating Liquids of Petroleum Origin, and Askarels

D1932-19: Standard Test Method for Thermal Endurance of Flexible Electrical Insulating Varnishes

D1933-03(2017): Standard Specification for Nitrogen Gas as an Electrical Insulating Material

D1934-95(2012): Standard Test Method for Oxidative Aging of Electrical Insulating Petroleum Oils by Open-Beaker Method

D197-19: Standard Test Method for Sampling and Fineness Test of Pulverized Coal

D2013/D2013M-20: Standard Practice for Preparing Coal Samples for Analysis

D2014/D2014M-20: Standard Test Method for Expansion or Contraction of Coal by the Sole-Heated Oven

D202-17: Standard Test Methods for Sampling and Testing Untreated Paper Used for Electrical Insulation

D2029-97(2017): Standard Test Methods for Water Vapor Content of Electrical Insulating Gases by Measurement of Dew Point

D2112-15: Standard Test Method for Oxidation Stability of Inhibited Mineral Insulating Oil by Pressure Vessel

D2129-17: Standard Test Method for Color of Clear Electrical Insulating Liquids (Platinum-Cobalt Scale)

D2144-07(2013): Standard Practices for Examination of Electrical Insulating Oils by Infrared Absorption

D2148-19: Standard Test Methods for Bondable Silicone Rubber Tapes Used for Electrical Insulation

D2149-13: Standard Test Method for Permittivity (Dielectric Constant) And Dissipation Factor Of Solid Ceramic Dielectrics At Frequencies To 10 MHz And Temperatures To 500°C

D2225-04(2012): Standard Test Methods for Silicone Fluids Used for Electrical Insulation

D2275-14: Standard Test Method for Voltage Endurance of Solid Electrical Insulating Materials Subjected to Partial Discharges (Corona) on the Surface

D2284-11(2019): Standard Test Method for Acidity of Sulfur Hexafluoride

D229-19e1: Standard Test Methods for Rigid Sheet and Plate Materials Used for Electrical Insulation

D2300-08(2017): Standard Test Method for Gassing of Electrical Insulating Liquids Under Electrical Stress and Ionization (Modified Pirelli Method)

D2303-20: Standard Test Methods for Liquid-Contaminant, Inclined-Plane Tracking and Erosion of Insulating Materials

D2304-18: Standard Test Method for Thermal Endurance of Rigid Electrical Insulating Materials

D2305-18: Standard Test Methods for Polymeric Films Used for Electrical Insulation

D2440-13: Standard Test Method for Oxidation Stability of Mineral Insulating Oil

D2472-15: Standard Specification for Sulfur Hexafluoride

D2477-07(2012): Standard Test Method for Dielectric Breakdown Voltage and Dielectric Strength of Insulating Gases at Commercial Power Frequencies

D2492-02(2012): Standard Test Method for Forms of Sulfur in Coal

D2519-19a: Standard Test Method for Bond Strength of Electrical Insulating Varnishes by the Helical Coil Test

D2520-13: Standard Test Methods for Complex Permittivity (Dielectric Constant) of Solid Electrical Insulating Materials at Microwave Frequencies and Temperatures to 1650oC

D2633-13a: Standard Test Methods for Thermoplastic Insulations and Jackets for Wire and Cable

D2639/D2639M-19: Standard Test Method for Plastic Properties of Coal by the Constant-Torque Gieseler Plastometer

D2656-13: Standard Specification for Crosslinked Polyethylene Insulation for Wire and Cable Rated 2001 to 35 000 V

D2668-07(2013): Standard Test Method for 2,6-di-tert-Butyl- p-Cresol and 2,6-di-tert-Butyl Phenol in Electrical Insulating Oil by Infrared Absorption

D2685-11(2019): Standard Test Method for Air and Carbon Tetrafluoride in Sulfur Hexafluoride by Gas Chromatography

D2686-19: Standard Specification for Polytetrafluoroethylene-Backed Pressure-Sensitive Electrical Insulating Tape

D2754-10(2016): Standard Specification for High-Temperature Glass Cloth Pressure-Sensitive Electrical Insulating Tape

D2759-00(2017): Standard Practice for Sampling Gas from a Transformer Under Positive Pressure

D2797/D2797M-20a: Standard Practice for Preparing Coal Samples for Microscopical Analysis by Reflected Light

D2798-20: Standard Test Method for Microscopical Determination of the Vitrinite Reflectance of Coal

D2799-13: Standard Test Method for Microscopical Determination of the Maceral Composition of Coal

D291-07(2012): Standard Test Method for Cubic Foot Weight of Crushed Bituminous Coal

D293/D293M-18: Standard Test Method for the Sieve Analysis of Coke

D2961/D2961M-19: Standard Practice for Single-Stage Total Moisture Less than 15 % in Coal Reduced to 2.36 mm [No. 8 Sieve] Topsize

D3004-08(2020): Standard Specification for Crosslinked and Thermoplastic Extruded Semi-Conducting, Conductor, and Insulation Shielding Materials

D3005-17: Standard Specification for Low-Temperature Resistant Vinyl Chloride Plastic Pressure-Sensitive Electrical Insulating Tape

D3006-10(2017): Standard Specification for Polyethylene Plastic Pressure-Sensitive Electrical Insulating Tape

D3038-93(2018): Standard Test Method for Drop Shatter Test for Coke

D3056-14(2018): Standard Test Method for Gel Time of Solventless Varnishes

D3144-00(2013)e1: Standard Specification for Crosslinked Poly(Vinylidene Fluoride) Heat-Shrinkable Tubing for Electrical Insulation

D3145-20: Standard Test Method for Thermal Endurance of Electrical Insulating Varnishes by Helical Coil Method

D3172-13: Standard Practice for Proximate Analysis of Coal and Coke

D3174-12(2018)e1: Standard Test Method for Ash in the Analysis Sample of Coal and Coke from Coal

D3175-20: Standard Test Method for Volatile Matter in the Analysis Sample of Coal and Coke

D3176-15: Standard Practice for Ultimate Analysis of Coal and Coke

D3180-15: Standard Practice for Calculating Coal and Coke Analyses from As-Determined to Different Bases

D3251-19: Standard Test Method for Thermal Endurance Characteristics of Electrical Insulating Varnishes Applied Over Film-Insulated Magnet Wire

D3283-98(2012): Standard Specification for Air as an Electrical Insulating Material

D3284-05(2019): Standard Practice for Combustible Gases in the Gas Space of Electrical Apparatus Using Portable Meters

D3288/D3288M-20: Standard Test Methods for Magnet-Wire Enamels

D3300-12: Standard Test Method for Dielectric Breakdown Voltage of Insulating Oils of Petroleum Origin Under Impulse Conditions

D3312-18: Standard Test Method for Percent Reactive Monomer in Solventless Varnishes

D3353-18: Standard Test Methods for Fibrous-Insulated Magnet Wire

D3377-04(2018): Standard Test Method for Weight Loss of Solventless Varnishes

D3380-14: Standard Test Method for Relative Permittivity (Dielectric Constant) and Dissipation Factor of Polymer-Based Microwave Circuit Substrates

D3382-13: Standard Test Methods for Measurement of Energy and Integrated Charge Transfer Due to Partial Discharges (Corona) Using Bridge Techniques

D3402/D3402M-16: Standard Test Method for Tumbler Test for Coke

D3426-19: Standard Test Method for Dielectric Breakdown Voltage and Dielectric Strength of Solid Electrical Insulating Materials Using Impulse Waves

D3455-11(2019): Standard Test Methods for Compatibility of Construction Material with Electrical Insulating Oil of Petroleum Origin

D346/D346M-11(2019)e1: Standard Practice for Collection and Preparation of Coke Samples for Laboratory Analysis

D3483-14: Standard Test Methods for Accumulated Deposition in a Steam Generator Tube

D3487-16e1: Standard Specification for Mineral Insulating Oil Used in Electrical Apparatus

D350-13: Standard Test Methods for Flexible Treated Sleeving Used for Electrical Insulation

D3554-20e1: Standard Specification for Track-Resistant Thermoplastic High-Density Polyethylene Insulation for Wire and Cable, 75 °C Operation

D3555-20e1: Standard Specification for Track-Resistant Crosslinked Polyethylene Insulation for Wire and Cable, 90 °C Operation

D3635-13: Standard Test Method for Dissolved Copper In Electrical Insulating Oil By Atomic Absorption Spectrophotometry

D3638-12: Standard Test Method for Comparative Tracking Index of Electrical Insulating Materials

D3667-16: Standard Specification for Rubber Seals Used in Flat-Plate Solar Collectors

D3682-13: Standard Test Method for Major and Minor Elements in Combustion Residues from Coal Utilization Processes

D3756-18: Standard Test Method for Evaluation of Resistance to Electrical Breakdown by Treeing in Solid Dielectric Materials Using Diverging Fields

D3771-15: Standard Specification for Rubber Seals Used in Concentrating Solar Collectors

D3803-91(2014): Standard Test Method for Nuclear-Grade Activated Carbon

D3832-79(2017): Standard Specification for Rubber Seals Contacting Liquids in Solar Energy Systems

D3843-16: Standard Practice for Quality Assurance for Protective Coatings Applied to Nuclear Facilities

D3850-19: Standard Test Method for Rapid Thermal Degradation of Solid Electrical Insulating Materials By Thermogravimetric Method (TGA)

D3874-20: Standard Test Method for Ignition of Materials by Hot Wire Sources

D388-19a: Standard Classification of Coals by Rank

D3903-15: Standard Specification for Rubber Seals Used in Air-Heat Transport of Solar Energy Systems

D3911-16: Standard Test Method for Evaluating Coatings Used in Light-Water Nuclear Power Plants at Simulated Design Basis Accident (DBA) Conditions

D3912-10(2017): Standard Test Method for Chemical Resistance of Coatings and Linings for Use in Nuclear Power Plants

D3955-20: Standard Specification for Electrical Insulating Varnishes

D3997/D3997M-16: Standard Practice for Preparing Coke Samples for Microscopical Analysis by Reflected Light

D4059-00(2018): Standard Test Method for Analysis of Polychlorinated Biphenyls in Insulating Liquids by Gas Chromatography

D4063-99(2016): Standard Specification for Pressboard for Electrical Insulating Purposes

D4082-10(2017): Standard Test Method for Effects of Gamma Radiation on Coatings for Use in Nuclear Power Plants

D4208-19: Standard Test Method for Total Chlorine in Coal by the Oxygen Vessel Combustion/Ion Selective Electrode Method

D4228-05(2017): Standard Practice for Qualification of Coating Applicators for Application of Coatings to Steel Surfaces

D4239-18e1: Standard Test Method for Sulfur in the Analysis Sample of Coal and Coke Using High-Temperature Tube Furnace Combustion

D4243-16: Standard Test Method for Measurement of Average Viscometric Degree of Polymerization of New and Aged Electrical Papers and Boards

D4245-08(2013): Standard Specification for Ozone-Resistant Thermoplastic Elastomer Insulation For Wire and Cable, 90°C Dry/75°C Wet Operation

D4246-14(2020): Standard Specification for Ozone-Resistant Thermoplastic Elastomer Insulation for Wire and Cable, 90 °C Operation

D4285-83(2018): Standard Test Method for Indicating Oil or Water in Compressed Air

D4286-08(2015): Standard Practice for Determining Coating Contractor Qualifications for Nuclear Powered Electric Generation Facilities

D4293-15e1: Standard Specification for Phosphate Ester Based Fluids for Turbine Lubrication and Steam Turbine Electro-Hydraulic Control (EHC) Applications

D4304-17: Standard Specification for Mineral and Synthetic Lubricating Oil Used in Steam or Gas Turbines

D4325-20: Standard Test Methods for Nonmetallic Semi-Conducting and Electrically Insulating Rubber Tapes

D4326-13: Standard Test Method for Major and Minor Elements in Coal and Coke Ash By X-Ray Fluorescence

D4378-20: Standard Practice for In-Service Monitoring of Mineral Turbine Oils for Steam, Gas, and Combined Cycle Turbines

D4388-20: Standard Specification for Nonmetallic Semi-Conducting and Electrically Insulating Rubber Tapes

D440-07(2019)e1: Standard Test Method of Drop Shatter Test for Coal

D441-07(2019)e1: Standard Test Method of Tumbler Test for Coal

D4470-18: Standard Test Method for Static Electrification

D4496-13: Standard Test Method for D-C Resistance or Conductance of Moderately Conductive Materials

D4537-12(2018): Standard Guide for Establishing Procedures to Qualify and Certify Personnel Performing Coating and Lining Work Inspection in Nuclear Facilities

D4538-15: Standard Terminology Relating to Protective Coating and Lining Work for Power Generation Facilities

D4559-99(2018): Standard Test Method for Volatile Matter in Silicone Fluid

D4566-14: Standard Test Methods for Electrical Performance Properties of Insulations and Jackets for Telecommunications Wire and Cable

D4568-13(2020): Standard Test Methods for Evaluating Compatibility Between Cable Filling and Flooding Compounds and Polyolefin Wire and Cable Materials

D4596-09(2015): Standard Practice for Collection of Channel Samples of Coal in a Mine

D4606-15: Standard Test Method for Determination of Arsenic and Selenium in Coal by the Hydride Generation/Atomic Absorption Method

D4618-92(2017): Standard Specification for Design and Fabrication of Flue Gas Desulfurization System Components for Protective Lining Application

D4652-05(2012): Standard Specification for Silicone Fluid Used for Electrical Insulation

D4730-13(2020): Standard Specification for Flooding Compounds for Telecommunications Wire and Cable

D4731-13(2020): Standard Specification for Hot-Application Filling Compounds for Telecommunications Wire and Cable

D4732-13(2020): Standard Specification for Cool-Application Filling Compounds for Telecommunications Wire and Cable

D4768-11(2019): Standard Test Method for Analysis of 2,6-Ditertiary-Butyl Para-Cresol and 2,6-Ditertiary-Butyl Phenol in Insulating Liquids by Gas Chromatography

D4872-14(2020): Standard Test Method for Dielectric Testing of Wire and Cable Filling Compounds

D4880-18: Standard Test Method for Salt Water Proofness of Insulating Varnishes Over Enamelled Magnet Wire

D4935-18: Standard Test Method for Measuring the Electromagnetic Shielding Effectiveness of Planar Materials

D4967-99(2013): Standard Guide for Selecting Materials to Be Used for Insulation, Jacketing and Strength Components in Fiber-Optic Cables

D5016-16: Standard Test Method for Total Sulfur in Coal and Coke Combustion Residues Using a High-Temperature Tube Furnace Combustion Method with Infrared Absorption

D5032-19: Standard Practice for Maintaining Constant Relative Humidity by Means of Aqueous Glycerin Solutions

D5061-19: Standard Test Method for Microscopical Determination of the Textural Components of Metallurgical Coke

D5114/D5114M-90(2018)e1: Standard Test Method for Laboratory Froth Flotation of Coal in a Mechanical Cell

D5139-19: Standard Specification for Sample Preparation for Qualification Testing of Coatings to be Used in Nuclear Power Plants

D5144-08(2016): Standard Guide for Use of Protective Coating Standards in Nuclear Power Plants

D5163-16: Standard Guide for Establishing a Program for Condition Assessment of Coating Service Level I Coating Systems in Nuclear Power Plants

D5192-09(2015): Standard Practice for Collection of Coal Samples from Core

D5213-19: Standard Specification for Polymeric Resin Film for Electrical Insulation and Dielectric Applications

D5222-16: Standard Specification for High Fire-Point Mineral Electrical Insulating Oils

D5263-15: Standard Test Method for Determining the Relative Degree of Oxidation in Bituminous Coal by Alkali Extraction

D5282-05(2012): Standard Test Methods for Compatibility of Construction Material with Silicone Fluid Used for Electrical Insulation

D5288-14: Standard Test Method for Determining Tracking Index of Electrical Insulating Materials Using Various Electrode Materials (Excluding Platinum)

D5341/D5341M-19: Standard Test Method for Measuring Coke Reactivity Index (CRI) and Coke Strength After Reaction (CSR)

D5364-14(2019): Standard Guide for Design, Fabrication, and Erection of Fiberglass Reinforced (FRP) Plastic Chimney Liners with Coal-Fired Units

D5367-16: Standard Practice for Evaluating Coatings Applied Over Surfaces Treated With Inhibitors Used to Prevent Flash Rusting of Steel When Water or Water/Abrasive Blasted

D5374-13: Standard Test Methods for Forced-Convection Laboratory Ovens for Evaluation of Electrical Insulation

D5411-10(2015): Standard Practice for Calculation of Average Energy Per Disintegration (¯E) for a Mixture of Radionuclides in Reactor Coolant

D5424-18: Standard Test Method for Smoke Obscuration of Insulating Materials Contained in Electrical or Optical Fiber Cables When Burning in a Vertical Cable Tray Configuration

D5425-18: Standard Guide for Development of Fire Hazard Assessment Standards of Electrotechnical Products

D5498-12a(2018): Standard Guide for Developing a Training Program for Personnel Performing Coating and Lining Work Inspection for Nuclear Facilities

D5499-94(2013): Standard Test Methods for Heat Resistance of Polymer Linings for Flue Gas Desulfurization Systems

D5537-18: Standard Test Method for Heat Release, Flame Spread, Smoke Obscuration, and Mass Loss Testing of Insulating Materials Contained in Electrical or Optical Fiber Cables When Burning in a Vertical Cable Tray Configuration

D5568-14: Standard Test Method for Measuring Relative Complex Permittivity and Relative Magnetic Permeability of Solid Materials at Microwave Frequencies Using Waveguide

D5638-18: Standard Test Method for Chemical Resistance of Electrical Insulating Varnishes

D5642-16: Standard Test Method for Sealed Tube Chemical Compatibility Test

D5671-95(2019): Standard Practice for Polishing and Etching Coal Samples for Microscopical Analysis by Reflected Light

D5837-15: Standard Test Method for Furanic Compounds in Electrical Insulating Liquids by High-Performance Liquid Chromatography (HPLC)

D6053-14(2018): Standard Test Method for Determination of Volatile Organic Compound (VOC) Content of Electrical Insulating Varnishes

D6095-12(2018): Standard Test Method for Longitudinal Measurement of Volume Resistivity for Extruded Crosslinked and Thermoplastic Semiconducting Conductor and Insulation Shielding Materials

D6096-11(2016): Standard Specification for Poly(Vinyl Chloride) Insulation for Wire and Cable, 90°C Operation

D6137-97(2018): Standard Test Method for Sulfuric Acid Resistance of Polymer Linings for Flue Gas Desulfurization Systems

D6172/D6172M-18: Standard Test Method for Determining the Volume of Bulk Materials Using Contours or Cross Sections Created by Direct Operator Compilation Using Photogrammetric Procedures

D6194-18: Standard Test Method for Glow-Wire Ignition of Materials

D6224-16: Standard Practice for In-Service Monitoring of Lubricating Oil for Auxiliary Power Plant Equipment

D6272-17e1: Standard Test Method for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials by Four-Point Bending

D6316-17: Standard Test Method for Determination of Total, Combustible and Carbonate Carbon in Solid Residues from Coal and Coke

D6343-14(2018): Standard Test Methods for Thin Thermally Conductive Solid Materials for Electrical Insulation and Dielectric Applications

D6347/D6347M-05(2018): Standard Test Method for Determination of Bulk Density of Coal Using Nuclear Backscatter Depth Density Methods

D6349-13: Standard Test Method for Determination of Major and Minor Elements in Coal, Coke, and Solid Residues from Combustion of Coal and Coke by Inductively Coupled Plasma—Atomic Emission Spectrometry

D6357-19: Standard Test Methods for Determination of Trace Elements in Coal, Coke, and Combustion Residues from Coal Utilization Processes by Inductively Coupled Plasma Atomic Emission Spectrometry, Inductively Coupled Plasma Mass Spectrometry, and Graphite Furnace Atomic Absorption Spectrometry

D6414-14: Standard Test Methods for Total Mercury in Coal and Coal Combustion Residues by Acid Extraction or Wet Oxidation/Cold Vapor Atomic Absorption

D6439-11(2017): Standard Guide for Cleaning, Flushing, and Purification of Steam, Gas, and Hydroelectric Turbine Lubrication Systems

D6448-16: Standard Specification for Industrial Burner Fuels from Used Lubricating Oils

D6522-20: Standard Test Method for Determination of Nitrogen Oxides, Carbon Monoxide, and Oxygen Concentrations in Emissions from Natural Gas-Fired Reciprocating Engines, Combustion Turbines, Boilers, and Process Heaters Using Portable Analyzers

D6542-05(2018)e1: Standard Practice for Tonnage Calculation of Coal in a Stockpile

D6609-17: Standard Guide for Part-Stream Sampling of Coal

D6721-01(2015): Standard Test Method for Determination of Chlorine in Coal by Oxidative Hydrolysis Microcoulometry

D6722-19: Standard Test Method for Total Mercury in Coal and Coal Combustion Residues by Direct Combustion Analysis

D6786-15: Standard Test Method for Particle Count in Mineral Insulating Oil Using Automatic Optical Particle Counters

D6796-16: Standard Practice for Production of Coal, Coke and Coal Combustion Samples for Interlaboratory Studies

D6823-08(2013): Standard Specification for Commercial Boiler Fuels With Used Lubricating Oils

D69-19: Standard Test Methods for Friction Tapes

D7013/D7013M-15: Standard Guide for Calibration Facility Setup for Nuclear Surface Gauges

D710-19: Standard Specification for Vulcanized Fibre Sheets, Rolls, Rods, and Tubes Used for Electrical Insulation

D7108-12(2018): Standard Guide for Establishing Qualifications for a Nuclear Coatings Specialist

D7148-19a: Standard Test Method for Determining the Ionic Resistivity (ER) of Alkaline Battery Separator Using a Carbon Electrode in an Electrolyte Bath Measuring System

D7150-13: Standard Test Method for the Determination of Gassing Characteristics of Insulating Liquids Under Thermal Stress

D7151-15: Standard Test Method for Determination of Elements in Insulating Oils by Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES)

D7155-20: Standard Practice for Evaluating Compatibility of Mixtures of Turbine Lubricating Oils

D7167-12(2018): Standard Guide for Establishing Procedures to Monitor the Performance of Safety-Related Coating Service Level III Lining Systems in an Operating Nuclear Power Plant

D720/D720M-15e1: Standard Test Method for Free-Swelling Index of Coal

D7219-19: Standard Specification for Isotropic and Near-isotropic Nuclear Graphites

D7230-06(2013): Standard Guide for Evaluating Polymeric Lining Systems for Water Immersion in Coating Service Level III Safety-Related Applications on Metal Substrates

D7265-12(2018): Standard Specification for Hydrogen Thermophysical Property Tables

D7301-11(2015): Standard Specification for Nuclear Graphite Suitable for Components Subjected to Low Neutron Irradiation Dose

D7321-18a: Standard Test Method for Particulate Contamination of Biodiesel B100 Blend Stock Biodiesel Esters and Biodiesel Blends by Laboratory Filtration

D7348-13: Standard Test Methods for Loss on Ignition (LOI) of Solid Combustion Residues

D7449/D7449M-14: Standard Test Method for Measuring Relative Complex Permittivity and Relative Magnetic Permeability of Solid Materials at Microwave Frequencies Using Coaxial Air Line

D7459-08(2016): Standard Practice for Collection of Integrated Samples for the Speciation of Biomass (Biogenic) and Fossil-Derived Carbon Dioxide Emitted from Stationary Emissions Sources

D7491-08(2015): Standard Guide for Management of Non-Conforming Coatings in Coating Service Level I Areas of Nuclear Power Plants

D7501-18a: Standard Test Method for Determination of Fuel Filter Blocking Potential of Biodiesel (B100) Blend Stock by Cold Soak Filtration Test (CSFT)

D7569/D7569M-10(2015)e1: Standard Practice for Determination of Gas Content of Coal—Direct Desorption Method

D7582-15: Standard Test Methods for Proximate Analysis of Coal and Coke by Macro Thermogravimetric Analysis

D7602-11(2017): Standard Practice for Installation of Vulcanized Rubber Linings

D7606-17: Standard Practice for Sampling of High Pressure Hydrogen and Related Fuel Cell Feed Gases

D7634-10(2017): Standard Test Method for Visualizing Particulate Sizes and Morphology of Particles Contained in Hydrogen Fuel by Microscopy

D7646-10(2019): Standard Test Method for Determination of Cooling Characteristics of Aqueous Polymer Quenchants for Aluminum Alloys by Cooling Curve Analysis

D7649-19: Standard Test Method for Determination of Trace Carbon Dioxide, Argon, Nitrogen, Oxygen and Water in Hydrogen Fuel by Jet Pulse Injection and Gas Chromatography/Mass Spectrometer Analysis

D7650-13: Standard Test Method for Sampling of Particulate Matter in High Pressure Hydrogen used as a Gaseous Fuel with an In-Stream Filter

D7651-17: Standard Test Method for Gravimetric Measurement of Particulate Concentration of Hydrogen Fuel

D7653-18: Standard Test Method for Determination of Trace Gaseous Contaminants in Hydrogen Fuel by Fourier Transform Infrared (FTIR) Spectroscopy

D7666-12(2019): Standard Specification for Triglyceride Burner Fuel

D7675-15: Standard Test Method for Determination of Total Hydrocarbons in Hydrogen by FID-Based Total Hydrocarbon (THC) Analyzer

D7708-14: Standard Test Method for Microscopical Determination of the Reflectance of Vitrinite Dispersed in Sedimentary Rocks

D7727-11(2016): Standard Practice for Calculation of Dose Equivalent Xenon (DEX) for Radioactive Xenon Fission Products in Reactor Coolant

D7759/D7759M-14: Standard Guide for Nuclear Surface Moisture and Density Gauge Calibration

D7800/D7800M-14: Standard Test Method for Determination of Elemental Sulfur in Natural Gas

D7830/D7830M-14: Standard Test Method for In-Place Density (Unit Weight) and Water Content of Soil Using an Electromagnetic Soil Density Gauge

D7843-18: Standard Test Method for Measurement of Lubricant Generated Insoluble Color Bodies in In-Service Turbine Oils using Membrane Patch Colorimetry

D785-08(2015): Standard Test Method for Rockwell Hardness of Plastics and Electrical Insulating Materials

D7863-17: Standard Guide for Evaluation of Convective Heat Transfer Coefficient of Liquids

D7894/D7894M-19: Standard Test Method for Thermal Endurance of Coating Powders Used for Integral Bus Bar Insulation Systems

D7895/D7895M-19: Standard Test Method for Thermal Endurance of Coating Powders Used for Powder Coating Insulation Systems

D790-17: Standard Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials

D7938-15: Standard Practice for Sampling of C-14 in Gaseous Effluents

D7941/D7941M-14: Standard Test Method for Hydrogen Purity Analysis Using a Continuous Wave Cavity Ring-Down Spectroscopy Analyzer

D7945-20: Standard Test Method for Determination of Dynamic Viscosity and Derived Kinematic Viscosity of Liquids by Constant Pressure Viscometer

D7975-14: Standard Test Method for Determination of Vapor Pressure of Crude Oil: VPCRx-F(Tm°C)(Manual Expansion Field Method)

D7978-14(2019): Standard Test Method for Determination of the Viable Aerobic Microbial Content of Fuels and Associated Water—Thixotropic Gel Culture Method

D7999-15(2019): Standard Classification for Rubber Products in Natural Gas Pipeline Applications

D8039-16: Standard Specification for Heat Transfer Fluids (HTF) for Heating and Air Conditioning (HVAC) Systems

D8091-16: Standard Guide for Impregnation of Graphite with Molten Salt

D8093-19: Standard Guide for Nondestructive Evaluation of Nuclear Grade Graphite

D8104-17: Standard Guide for Determining Coating Qualification Test Data Applicability

D8112-17: Standard Guide for Obtaining In-Service Samples of Turbine Operation Related Lubricating Fluid

D831/D831M-12: Standard Test Method for Gas Content of Cable and Capacitor Oils

D876-13: Standard Test Methods for Nonrigid Vinyl Chloride Polymer Tubing Used for Electrical Insulation

D877/D877M-19: Standard Test Method for Dielectric Breakdown Voltage of Insulating Liquids Using Disk Electrodes

D922-18: Standard Specification for Nonrigid Vinyl Chloride Polymer Tubing

D923-15: Standard Practices for Sampling Electrical Insulating Liquids

D924-15: Standard Test Method for Dissipation Factor (or Power Factor) and Relative Permittivity (Dielectric Constant) of Electrical Insulating Liquids

D952-15: Standard Test Method for Bond or Cohesive Strength of Sheet Plastics and Electrical Insulating Materials

D971-20: Standard Test Method for Interfacial Tension of Insulating Liquids Against Water by the Ring Method

E1005-16: Standard Test Method for Application and Analysis of Radiometric Monitors for Reactor Vessel Surveillance

E1006-13: Standard Practice for Analysis and Interpretation of Physics Dosimetry Results from Test Reactor Experiments

E1018-20e1: Standard Guide for Application of ASTM Evaluated Cross Section Data File

E1021-15(2019): Standard Test Method for Spectral Responsivity Measurements of Photovoltaic Devices

E1034-95(2020): Standard Specification for Nuclear Facility Transient Worker Records

E1035-18: Standard Practice for Determining Neutron Exposures for Nuclear Reactor Vessel Support Structures

E1036-15(2019): Standard Test Methods for Electrical Performance of Nonconcentrator Terrestrial Photovoltaic Modules and Arrays Using Reference Cells

E1038-10(2019): Standard Test Method for Determining Resistance of Photovoltaic Modules to Hail by Impact with Propelled Ice Balls

E1040-10(2020): Standard Specification for Physical Characteristics of Nonconcentrator Terrestrial Photovoltaic Reference Cells

E1056-13: Standard Practice for Installation and Service of Solar Domestic Water Heating Systems for One- and Two-Family Dwellings

E1084-86(2015): Standard Test Method for Solar Transmittance (Terrestrial) of Sheet Materials Using Sunlight

E1125-16(2020): Standard Test Method for Calibration of Primary Non-Concentrator Terrestrial Photovoltaic Reference Cells Using a Tabular Spectrum

E1143-05(2019): Standard Test Method for Determining the Linearity of a Photovoltaic Device Parameter with Respect To a Test Parameter

E1160-13: Standard Guide for On-Site Inspection and Verification of Operation of Solar Domestic Hot Water Systems

E1167-15: Standard Guide for Radiation Protection Program for Decommissioning Operations

E1168-95(2020): Standard Guide for Radiological Protection Training for Nuclear Facility Workers

E1171-15(2019): Standard Test Methods for Photovoltaic Modules in Cyclic Temperature and Humidity Environments

E1175-87(2015): Standard Test Method for Determining Solar or Photopic Reflectance, Transmittance, and Absorptance of Materials Using a Large Diameter Integrating Sphere

E1249-15: Standard Practice for Minimizing Dosimetry Errors in Radiation Hardness Testing of Silicon Electronic Devices Using Co-60 Sources

E1250-15(2020): Standard Test Method for Application of Ionization Chambers to Assess the Low Energy Gamma Component of Cobalt-60 Irradiators Used in Radiation-Hardness Testing of Silicon Electronic Devices

E1253-13: Standard Guide for Reconstitution of Irradiated Charpy-Sized Specimens

E1281-15: Standard Guide for Nuclear Facility Decommissioning Plans

E1297-18: Standard Test Method for Measuring Fast-Neutron Reaction Rates by Radioactivation of Niobium

E1358-97(2019): Standard Test Method for Determination of Moisture Content of Particulate Wood Fuels Using a Microwave Oven

E1362-15(2019): Standard Test Methods for Calibration of Non-Concentrator Photovoltaic Non-Primary Reference Cells

E1462-12(2018): Standard Test Methods for Insulation Integrity and Ground Path Continuity of Photovoltaic Modules

E1534-93(2019): Standard Test Method for Determination of Ash Content of Particulate Wood Fuels

E1597-10(2019): Standard Test Method for Saltwater Pressure Immersion and Temperature Testing of Photovoltaic Modules for Marine Environments

E1606-20: Standard Practice for Electromagnetic (Eddy Current) Examination of Copper and Aluminum Redraw Rod for Electrical Purposes

E1675-20: Standard Practice for Sampling Two-Phase Geothermal Fluid for Purposes of Chemical Analysis

E1690-08(2016): Standard Test Method for Determination of Ethanol Extractives in Biomass

E1721-01(2020): Standard Test Method for Determination of Acid-Insoluble Residue in Biomass

E1755-01(2020): Standard Test Method for Ash in Biomass

E1756-08(2020): Standard Test Method for Determination of Total Solids in Biomass

E1757-19: Standard Practice for Preparation of Biomass for Compositional Analysis

E1758-01(2020): Standard Test Method for Determination of Carbohydrates in Biomass by High Performance Liquid Chromatography

E1760-16: Standard Guide for Unrestricted Disposition of Bulk Materials Containing Residual Amounts of Radioactivity

E1799-12(2018): Standard Practice for Visual Inspections of Photovoltaic Modules

E18-20: Standard Test Methods for Rockwell Hardness of Metallic Materials

E1802-12(2018): Standard Test Methods for Wet Insulation Integrity Testing of Photovoltaic Modules

E181-17: Standard Test Methods for Detector Calibration and Analysis of Radionuclides

E1819-15: Standard Guide for Environmental Monitoring Plans for Decommissioning of Nuclear Facilities

E1821-08(2020): Standard Test Method for Determination of Carbohydrates in Biomass by Gas Chromatography

E1830-15(2019): Standard Test Methods for Determining Mechanical Integrity of Photovoltaic Modules

E1854-19: Standard Practice for Ensuring Test Consistency in Neutron-Induced Displacement Damage of Electronic Parts

E1855-20: Standard Test Method for Use of 2N2222A Silicon Bipolar Transistors as Neutron Spectrum Sensors and Displacement Damage Monitors

E1892-15: Standard Guide for Preparing Characterization Plans for Decommissioning Nuclear Facilities

E1893-15: Standard Guide for Selection and Use of Portable Radiological Survey Instruments for Performing In Situ Radiological Assessments to Support Unrestricted Release from Further Regulatory Controls

E1894-18: Standard Guide for Selecting Dosimetry Systems for Application in Pulsed X-Ray Sources

E2005-10(2015): Standard Guide for Benchmark Testing of Reactor Dosimetry in Standard and Reference Neutron Fields

E2006-16: Standard Guide for Benchmark Testing of Light Water Reactor Calculations

E2047-10(2019): Standard Test Method for Wet Insulation Integrity Testing of Photovoltaic Arrays

E2096/E2096M-16: Standard Practice for In Situ Examination of Ferromagnetic Heat-Exchanger Tubes Using Remote Field Testing

E2216-02(2020): Standard Guide for Evaluating Disposal Options for Concrete from Nuclear Facility Decommissioning

E2236-10(2019): Standard Test Methods for Measurement of Electrical Performance and Spectral Response of Nonconcentrator Multijunction Photovoltaic Cells and Modules

E2420-15: Standard Guide for Post-Deactivation Surveillance and Maintenance of Radiologically Contaminated Facilities

E2421-15: Standard Guide for Preparing Waste Management Plans for Decommissioning Nuclear Facilities

E2450-16: Standard Practice for Application of CaF2(Mn) Thermoluminescence Dosimeters in Mixed Neutron-Photon Environments

E2481-12(2018): Standard Test Method for Hot Spot Protection Testing of Photovoltaic Modules

E2527-15(2019): Standard Test Method for Electrical Performance of Concentrator Terrestrial Photovoltaic Modules and Systems Under Natural Sunlight

E261-16: Standard Practice for Determining Neutron Fluence, Fluence Rate, and Spectra by Radioactivation Techniques

E262-17: Standard Test Method for Determining Thermal Neutron Reaction Rates and Thermal Neutron Fluence Rates by Radioactivation Techniques

E263-18: Standard Test Method for Measuring Fast-Neutron Reaction Rates by Radioactivation of Iron

E264-19: Standard Test Method for Measuring Fast-Neutron Reaction Rates by Radioactivation of Nickel

E265-15(2020): Standard Test Method for Measuring Reaction Rates and Fast-Neutron Fluences by Radioactivation of Sulfur-32

E2685-15(2019): Standard Specification for Steel Blades Used with the Photovoltaic Module Surface Cut Test

E2766-13(2019): Standard Practice for Installation of Roof Mounted Photovoltaic Arrays on Steep-Slope Roofs

E2848-13(2018): Standard Test Method for Reporting Photovoltaic Non-Concentrator System Performance

E2908-12(2018): Standard Guide for Fire Prevention for Photovoltaic Panels, Modules, and Systems

E2939-13(2018): Standard Practice for Determining Reporting Conditions and Expected Capacity for Photovoltaic Non-Concentrator Systems

E2971-16: Standard Test Method for Determination of Effective Boron-10 Areal Density in Aluminum Neutron Absorbers using Neutron Attenuation Measurements

E2997-16: Standard Test Method for Analysis of Biodiesel Products by Gas Chromatography-Mass Spectrometry

E3006-20: Standard Practice for Ultraviolet Conditioning of Photovoltaic Modules or Mini-Modules Using a Fluorescent Ultraviolet (UV) Lamp Apparatus

E3010-15(2019): Standard Practice for Installation, Commissioning, Operation, and Maintenance Process (ICOMP) of Photovoltaic Arrays

E3044/E3044M-16e1: Standard Practice for Ultrasonic Testing of Polyethylene Butt Fusion Joints

E3045-16: Standard Practice for Crack Detection Using Vibroacoustic Thermography

E3053-18e1: Standard Test Method for Determining Particulate Matter Emissions from Wood Heaters Using Cordwood Test Fuel

E3066-20: Standard Practice for Evaluating Relative Sustainability Involving Energy or Chemicals from Biomass

E3083-17: Standard Terminology Relating to Radiation Processing: Dosimetry and Applications

E3084-17: Standard Practice for Characterizing Particle Irradiations of Materials in Terms of Non-Ionizing Energy Loss (NIEL)

E321-96(2012): Standard Test Method for Atom Percent Fission in Uranium and Plutonium Fuel (Neodymium-148 Method)

E385-16: Standard Test Method for Oxygen Content Using a 14-MeV Neutron Activation and Direct-Counting Technique

E393-19: Standard Test Method for Measuring Reaction Rates by Analysis of Barium-140 From Fission Dosimeters

E424-71(2015): Standard Test Methods for Solar Energy Transmittance and Reflectance (Terrestrial) of Sheet Materials

E481-16: Standard Test Method for Measuring Neutron Fluence Rates by Radioactivation of Cobalt and Silver

E482-16: Standard Guide for Application of Neutron Transport Methods for Reactor Vessel Surveillance

E496-14e1: Standard Test Method for Measuring Neutron Fluence and Average Energy from 3H(d,n) 4He Neutron Generators by Radioactivation Techniques

E509/E509M-14: Standard Guide for In-Service Annealing of Light-Water Moderated Nuclear Reactor Vessels

E531-13: Standard Practice for Surveillance Testing of High-Temperature Nuclear Component Materials

E666-14: Standard Practice for Calculating Absorbed Dose From Gamma or X Radiation

E668-20: Standard Practice for Application of Thermoluminescence-Dosimetry (TLD) Systems for Determining Absorbed Dose in Radiation-Hardness Testing of Electronic Devices

E683-91(2013): Standard Practice for Installation and Service of Solar Space Heating Systems for One- and Two-Family Dwellings

E690-15(2020): Standard Practice for In Situ Electromagnetic (Eddy Current) Examination of Nonmagnetic Heat Exchanger Tubes

E704-19: Standard Test Method for Measuring Reaction Rates by Radioactivation of Uranium-238

E705-18: Standard Test Method for Measuring Reaction Rates by Radioactivation of Neptunium-237

E720-16: Standard Guide for Selection and Use of Neutron Sensors for Determining Neutron Spectra Employed in Radiation-Hardness Testing of Electronics

E722-19: Standard Practice for Characterizing Neutron Fluence Spectra in Terms of an Equivalent Monoenergetic Neutron Fluence for Radiation-Hardness Testing of Electronics

E744-07(2015): Standard Practice for Evaluating Solar Absorptive Materials for Thermal Applications

E772-15: Standard Terminology of Solar Energy Conversion

E781-86(2015): Standard Practice for Evaluating Absorptive Solar Receiver Materials When Exposed to Conditions Simulating Stagnation in Solar Collectors With Cover Plates

E782-95(2015): Standard Practice for Exposure of Cover Materials for Solar Collectors to Natural Weathering Under Conditions Simulating Operational Mode

E798-16: Standard Practice for Conducting Irradiations at Accelerator-Based Neutron Sources

E821-16: Standard Practice for Measurement of Mechanical Properties During Charged-Particle Irradiation

E822-92(2015): Standard Practice for Determining Resistance of Solar Collector Covers to Hail by Impact With Propelled Ice Balls

E853-18: Standard Practice for Analysis and Interpretation of Light-Water Reactor Surveillance Neutron Exposure Results

E854-19: Standard Test Method for Application and Analysis of Solid State Track Recorder (SSTR) Monitors for Reactor Surveillance

E861-13: Standard Practice for Evaluating Thermal Insulation Materials for Use in Solar Collectors

E870-82(2019): Standard Test Methods for Analysis of Wood Fuels

E871-82(2019): Standard Test Method for Moisture Analysis of Particulate Wood Fuels

E872-82(2019): Standard Test Method for Volatile Matter in the Analysis of Particulate Wood Fuels

E873-82(2019): Standard Test Method for Bulk Density of Densified Particulate Biomass Fuels

E881-92(2015): Standard Practice for Exposure of Solar Collector Cover Materials to Natural Weathering Under Conditions Simulating Stagnation Mode

E900-15e2: Standard Guide for Predicting Radiation-Induced Transition Temperature Shift in Reactor Vessel Materials

E903-12: Standard Test Method for Solar Absorptance, Reflectance, and Transmittance of Materials Using Integrating Spheres

E905-87(2013): Standard Test Method for Determining Thermal Performance of Tracking Concentrating Solar Collectors

E910-18: Standard Test Method for Application and Analysis of Helium Accumulation Fluence Monitors for Reactor Vessel Surveillance

E927-19: Standard Classification for Solar Simulators for Electrical Performance Testing of Photovoltaic Devices

E942-16: Standard Guide for Investigating the Effects of Helium in Irradiated Metals

E944-19: Standard Guide for Application of Neutron Spectrum Adjustment Methods in Reactor Surveillance

E947-83(2015): Standard Specification for Sampling Single-Phase Geothermal Liquid or Steam for Purposes of Chemical Analysis

E948-16(2020): Standard Test Method for Electrical Performance of Photovoltaic Cells Using Reference Cells Under Simulated Sunlight

E953/E953M-16: Standard Practice for Fusibility of Refuse-Derived Fuel (RDF) Ash

E957-03(2019): Standard Terminology Relating to Geothermal Energy

E971-11(2019): Standard Practice for Calculation of Photometric Transmittance and Reflectance of Materials to Solar Radiation

E972-96(2013): Standard Test Method for Solar Photometric Transmittance of Sheet Materials Using Sunlight

F2249-20: Standard Specification for In-Service Test Methods for Temporary Grounding Jumper Assemblies Used on De-Energized Electric Power Lines and Equipment

F2321-14(2020): Standard Specification for Flexible and Rigid Insulated Temporary By-Pass Jumpers

F2715-19: Standard Specification for Temporary Protective Equipotential Bond Mat To Be Used on De-Energized Equipment

F3149-15: Standard Practice for Determining the Maintenance Factor (m) and Yield Factor (y) Loading Constants Applicable to Gasket Materials and Designs

F3235-17a: Standard Specification for Aircraft Storage Batteries

F526-16: Standard Test Method for Using Calorimeters for Total Dose Measurements in Pulsed Linear Accelerator or Flash X-ray Machines

ISO/ASTM51608-15: Standard Practice for Dosimetry in an X-Ray (Bremsstrahlung) Facility for Radiation Processing at Energies between 50 keV and 7.5 MeV

ISO/ASTM51649-15: Standard Practice for Dosimetry in an Electron Beam Facility for Radiation Processing at Energies Between 300 keV and 25 MeV

ISO/ASTM51707-15: Standard Guide for Estimation of Measurement Uncertainty in Dosimetry for Radiation Processing