Standard Active Last Updated: Sep 11, 2024 Track Document
ASTM G156-24

Standard Practice for Selecting and Characterizing Weathering Reference Materials

Standard Practice for Selecting and Characterizing Weathering Reference Materials G0156-24 ASTM|G0156-24|en-US Standard Practice for Selecting and Characterizing Weathering Reference Materials Standard new BOS Vol. 14.04 Committee G03
$ 69.00 In stock
ASTM International

Significance and Use

4.1 Weathering reference materials are used in laboratory accelerated exposure tests to verify consistency of tests run within the same instrument at different times (repeatability) or in different instruments or different laboratories (reproducibility), using the same exposure conditions, or both.

Note 2: Examples of weathering reference materials used for this purpose are given in SAE J2412 and SAE J2527 for clear polystyrene material and AATCC TM16.1-3 or ISO 105-B02 for blue wool material.

4.2 Weathering reference materials are used in natural weathering tests to evaluate consistency due to seasonal/annual variation or to analyze specific exposure variables (such as exposure angle, location, backing configuration, etc.).

4.3 Specifications defining consistency of exposure conditions are based on the property change of a reference material after a defined period of time. Some weathering reference materials are used to define periods of exposure. Specifications recommending the use of these materials require the material to be exposed until a defined change in the weathering reference material is achieved. Specifications are usually based on results for a single lot of the weathering reference material. When a new lot of the reference material is introduced, round-robin studies are necessary to compare the new and old lots and to establish appropriate limits for expected performance of the new lot.

Note 3: Some weathering reference materials (for example blue wools) are also used to define periods of exposure. Although not specifically covered by this standard, the procedures described for characterizing a reference material used to monitor consistency of exposures are also generally applicable to characterizing reference materials used to define periods of exposure.

4.4 It is important to test the consistency of exposure in the laboratory accelerated device with a weathering reference material that responds to the test conditions similar to the way the test materials respond. Therefore, it is preferable that the weathering reference material be sensitive to the spectral region of the light source mainly responsible for producing degradation in the test materials to provide the most meaningful evaluation of exposure test consistency, as well as providing information on consistency of temperature and humidity conditions if the latter are important factors in degradation of the test materials.

Note 4: Material homogeneity can also be an important factor in selection of a weathering reference material, particularly if weathering is initiated by the radiation absorbed by impurities as is the case in aliphatic type polymers exposed to radiation longer than 300 nm.

4.5 The measurement of the characteristic property of a weathering reference material can be subject to error depending on the instrument and the procedure used to measure the property. It is important to use measurement procedures that are clear and which minimize chances for operator misinterpretation. It is also important to determine the level of variability caused by measurement of the characteristic property.

4.6 When a reference material is used to monitor or specify the consistency of an exposure test, it is important that any specification limits defined by changes in the reference material be based on a sound statistical analysis of results from a properly designed round-robin experiment. This practice provides a procedure which can be followed to set up the round-robin, analyze results, and establish reasonable limits of change in the characteristic property of the reference material that can be used in specifications.

4.6.1 The results obtained according to this practice are valid only for the exposure cycle used for the round-robin and cannot be applied to the same weathering reference material used in different exposure cycles.

4.7 The change in characteristic property of a reference material may be affected by the placement of the reference material in the exposure device. This is often due to variations in light intensity and temperature within the allowed exposure area. Random placement of replicate specimens of the weathering reference material throughout the allowed exposure area provides an indication of the uniformity of conditions within the exposure area.

Note 5: In some cases, procedures require exposure of a weathering reference material at a specific location within the exposure device or chamber. Results for a reference material used in this way may not provide an accurate representation of the exposure conditions in other positions within the device.

Scope

1.1 This practice describes the criteria to be used for selection of a weathering reference material (WRM) and procedures to be used for determining within lab and between lab tolerances of changes in measured properties of weathering reference materials. This practice also describes a procedure for comparing different lots of the same type of a weathering reference material.

Note 1: Examples of laboratory accelerated tests in which a weathering reference material could be used to monitor consistency are exposure tests such as those described in Practices G152, G153, G154, and G155 and other standards in which tests conducted according to these standards are referenced. Examples of outdoor exposures where a weathering reference material could be used to monitor consistency are those conducted according to Practices G7, G24, or G90. A reference material can also be used to monitor consistency of exposure or conditioning test that do not involve exposure to light.

1.2 Weathering reference materials are most often used to (1) monitor consistency (that is, repeatability, reproducibility, or both) of exposure tests, (2) to determine the time or radiant exposure at which test materials are evaluated, (3) as a reference material for comparing to test materials exposed at the same time. Weathering reference materials cannot be used to classify or characterize the relative severity of any exposure test because of the large variability in material responses to the effects of light, heat, and water.

1.3 This practice does not cover control materials which, by definition are selected to be of similar composition and construction to the test materials, and are exposed at the same time as test materials.

1.4 This practice provides an outline of experiments required to determine how the measured properties of the reference material change as a function of exposure to specified test conditions. It includes establishment of reproducible measurement procedures, determination of the critical spectral region in the light source causing the changes, and effects of other critical exposure stresses such as temperature and moisture.

1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Price:
Contact Sales
Related
Reprints and Permissions
Reprints and copyright permissions can be requested through the
Copyright Clearance Center
Details
Book of Standards Volume: 14.04
Developed by Subcommittee: G03.01
Pages: 5
DOI: 10.1520/G0156-24
ICS Code: 19.040