Standard Active Last Updated: Nov 02, 2021 Track Document
ASTM F2781-15(2021)

Standard Practice for Testing Forced Entry, Ballistic and Low Impact Resistance of Security Fence Systems

Standard Practice for Testing Forced Entry, Ballistic and Low Impact Resistance of Security Fence Systems F2781-15R21 ASTM|F2781-15R21|en-US Standard Practice for Testing Forced Entry, Ballistic and Low Impact Resistance of Security Fence Systems Standard new BOS Vol. 01.06 Committee F14
$ 76.00 In stock

Significance and Use

5.1 The success or failure of any attempt to forcefully penetrate a fence system is dependent upon three primary factors that collectively define the threat—the tools and devices employed, the number of aggressors, and their level of sophistication.

5.2 Normally, a test procedure of this scope would be supported by years of laboratory testing intended to qualify and accurately reproduce the destructive effects of a variety of tools, implements, and devices. However, rapidly changing social conditions have created an immediate need for building components resistant to evolving forced entry techniques. Accordingly, the procedures presented herein are based more on field experience than laboratory analysis. They are more representative than inclusive, are intended to provide a basis for the comparative evaluation of different fence systems using forced penetration procedures, ballistic tests and impact testing, and are not primarily intended to be used to establish or confirm the absolute prevention of forced entries.

5.3 The test requirements specified herein have been established for use in evaluating the penetration resistance characteristics of standard fence systems to be used in commercial, government and military installations.

5.3.1 The success of any forced entry threat is dependent on the cumulative effect of the implements used, the elapsed time, and the sophistication and motivation of the personnel affecting the forced entry.

5.3.2 Absolute penetration resistance from forced entry by a determined and well-equipped attack group is impossible.

5.3.3 Aggressor groups range from unsophisticated criminals and vandals to organized criminals.

5.3.4 Attempts to force an entry may be thwarted by increasing the time necessary to affect such an entry and by early detection. Intrusion sensors positioned as far as possible from the protected environment in conjunction with optimal structural and component design will maximize the time available for a response force to intercept the intruders.

5.4 The procedures of this test method are intended to evaluate the time necessary for vandals and unsophisticated criminals to forcefully penetrate security fence systems by using manually operated tools—defined as a low, medium, or aggressive forced entry threat.

Scope

1.1 The forced entry resistance of fence systems is evaluated relative to three levels of forced entry threat using the limited hand tool inventory outlined in Table 1. It also establishes a system for rating the forced entry resistance of those systems (see Table 2). The tools specified to be used for testing at each threat level are those that are known to have a maximum destructive effect on structures and their sub-assemblies and are readily available to aggressors categorized as posing that level of threat.

1.1.1 Low Threat Level (L)—Specifically exempted from the inventory of available tools for the low (L) threat level category are power tools (gasoline, electric or hydraulic), and devices requiring more than one person to transport and operate.

1.1.2 Medium Threat Level (M)—Specifically exempted from the inventory of available tools for the medium (M) threat level category are power tools requiring an outside power source or self contained gasoline or battery driven tools and devices requiring more than two persons to transport and operate.

1.1.3 Aggressive Threat Level (A)—Specifically exempted from the inventory of available tools for the high (H) threat level category are devices requiring more than two persons to transport and operate.

1.2 The ability of a fence system to offer protection from bullets fired from a rifle or handgun would be beneficial particularly in Border Fence areas where security personnel can be targets during patrol activities. Accordingly, a limited test using a .38 Special handgun and a 7.62-mm rifle is performed to determine if any level of protection is provided by the fence system.

1.3 The ability of a fence system to provide impact resistance from a 4000 pound mass vehicle moving at a velocity of 20 MPH at a modest cost will provide relative guidance as to the strength of a security fence system in resisting low impact situations.

1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Price:
Contact Sales
Related
Reprints and Permissions
Reprints and copyright permissions can be requested through the
Copyright Clearance Center
Details
Book of Standards Volume: 01.06
Developed by Subcommittee: F14.50
Pages: 11
DOI: 10.1520/F2781-15R21
ICS Code: 13.310