Standard Historical Last Updated: Sep 21, 2023 Track Document
ASTM F1387-19

Standard Specification for Performance of Piping and Tubing Mechanically Attached Fittings

Standard Specification for Performance of Piping and Tubing Mechanically Attached Fittings F1387-19 ASTM|F1387-19|en-US Standard Specification for Performance of Piping and Tubing Mechanically Attached Fittings Standard new BOS Vol. 01.07 Committee F25
$ 119.00 In stock
ASTM International

Abstract

This specification establishes the performance characteristics required for mechanically attached fittings (MAFs) for use in piping and tubing systems. These fittings directly attach to pipe or tube by mechanical deformation of the pipe or tube or fitting, or a combination thereof, creating a seal and a restrained joint. process. MAFs covered here are classified into the following design types: Type Iradially swaged MAF (permanent); Type IIflared MAF (separable); Type IIIflareless (bite-type) MAF (separable); Type IVgrip-type MAF (separable); Type Vshape memory alloy (SMA) MAF (permanent); and Type VIaxially swaged MAF (permanent). Moreover, the MAFs shall be made from on or more of the following material grade: Grade Acarbon steel; Grade Bstainless steel; Grade Cnickel-copper; Grade Dcopper-nickel; Grade Ebrass; and Grade Fnickel titanium. The MAFs shall also be grouped into ten classes according to their pressure ratings. The standard qualification tests to which the MAFs shall perform satisfactorily are pneumatic proof test, hydrostatic proof test, impulse test, flexure fatigue test, tensile test, hydrostatic burst test, repeated assembly test, rotary flexure test, and mercurous nitrate test. Successful completion of the tests described constitutes completion of the technical portion of the qualification

Scope

1.1 This specification establishes the performance characteristics required for mechanically attached fittings (MAFs) for use in piping and tubing systems. These fittings directly attach to pipe or tube by mechanical deformation of the pipe or tube or fitting, or a combination thereof, creating a seal and a restrained joint. The seal may be created via the mechanical deformation or created independently. Successful completion of the tests described constitutes completion of the technical portion of the qualification process.

1.2 Supplementary requirements are provided for use when additional testing or inspection is desired. These shall apply only when specified in part or whole by the purchaser in the order. Unless otherwise specified, U.S. Navy contracts shall invoke the supplementary requirements in whole.

1.3 Unless specific MAF types are specified, the term “MAF” shall apply to all types described herein.

1.4 The tests specified in Section 13 and described in Annex A1 and the Supplementary Requirements Section are applicable only to ascertain the performance characteristics of MAFs. These tests are not intended for use in the evaluation of non-MAF products.

1.5 A fire performance test is specified in Supplementary Requirement S7. This test provides general guidelines to determine the responsiveness of MAFs when subjected to fire. This test should not be considered for use to evaluate non-MAF products.

1.6 The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard.

1.7 The following safety hazards caveat applies only to the tests listed in Section 13 and the tests described in the Supplementary Requirements Section and the annexes of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Price:
Contact Sales
Related
Reprints and Permissions
Reprints and copyright permissions can be requested through the
Copyright Clearance Center
Details
Book of Standards Volume: 01.07
Developed by Subcommittee: F25.11
Pages: 31
DOI: 10.1520/F1387-19
ICS Code: 23.060.01