Standard Historical Last Updated: Jun 25, 2021 Track Document
ASTM D7762-18

Standard Practice for Design of Stabilization of Soil and Soil-Like Materials with Self-Cementing Fly Ash

Standard Practice for Design of Stabilization of Soil and Soil-Like Materials with Self-Cementing Fly Ash D7762-18 ASTM|D7762-18|en-US Standard Practice for Design of Stabilization of Soil and Soil-Like Materials with Self-Cementing Fly Ash Standard new BOS Vol. 04.09 Committee D18
$ 73.00 In stock

Significance and Use

4.1 Self-cementing coal fly ashes are suitable materials for the stabilization of soils, recycled pavement materials and road surface gravel. Fly ash stabilization can result in improved properties, including increased stiffness, strength and freeze-thaw durability; reduced hydraulic conductivity, plasticity, and swelling; and increased control of soil compressibility and moisture. Fly ash stabilized materials (FASM) may be used in roadway construction, such as working platforms during construction, stabilized subgrade, subbase, and base layers. Fly ash stabilization can also be used in limiting settlement of fills below buildings.

4.2 This practice is intended for use with self-cementing fly ash that can be used individually or along with other stabilizing admixtures to improve soil properties.

4.3 The practice describes the unique design considerations that may apply to stabilization of soils and soil-like materials with self-cementing coal fly ash. The requirements for stabilization of specific materials may vary due to local conditions or the intended use of the stabilized material, or both.

4.3.1 This practice is not intended to limit the flexibility of design in stabilization. The degree of success attained in stabilization with coal fly ash is highly dependent on the particular combination of soil, fly ash, and other additives and the construction procedure used. The selection of appropriate materials, applicable tests, acceptance criteria, and specification is the responsibility of the design engineer.

4.4 The test methods in this practice are intended for the determination of mechanical properties of FASM. The characterization of mechanical property improvement with self-cementing fly ash will assist in the evaluation of the fly ash stabilized materials.

4.5 The use of self-cementing fly ash in geotechnical engineering applications may be regulated by state and local codes. The codes should be consulted.

Scope

1.1 This practice covers procedures for the design of stabilization of soil and soil-like materials using self-cementing coal fly ash for roadway applications, treatment of expansive subgrade or organic subgrade, and limiting settlement of fills below buildings. The coal fly ash covered in this method includes self-cementing fly ashes described in Specification D5239.

1.2 The testing and engineering practices for self-cementing coal fly ash are similar to generally accepted practices for soil stabilization with fly ash and other pozzolans that require lime.

1.3 The test methods in this practice are applicable to the characterization of mechanical properties of in situ mixed self-cementing fly ash stabilized materials. Follow Practice D75 for sampling purposes. There are other related fly ash stabilization standards. Practice D5239 can be used to characterize the general types of fly ash for use in soil stabilization. Specification C593 can be used to evaluate the performance of fly ash and other pozzolans that require lime soil stabilization. Guide E2277 can be used to characterize properties of fly ash and bottom ash in structural fills and related design and construction considerations.

1.4 The standard units are the SI units, unless other units are specified.

1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.6 This practice offers a set of instructions for performing one or more specific operations. This document cannot replace education or experience and should be used in conjunction with professional judgment. Not all aspects of this practice may be applicable in all circumstances. This ASTM standard is not intended to represent or replace the standard of care by which the adequacy of a given professional service must be judged, nor should this document be applied without consideration of a project’s many unique aspects. The word “Standard” in the title of this document means only that the document has been approved through the ASTM consensus process.

1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Price:
Contact Sales
Related
Reprints and Permissions
Reprints and copyright permissions can be requested through the
Copyright Clearance Center
Details
Book of Standards Volume: 04.09
Developed by Subcommittee: D18.14
Pages: 4
DOI: 10.1520/D7762-18
ICS Code: 93.020