Standard Historical Last Updated: Jan 20, 2014 Track Document
ASTM D7258-09

Standard Specification for Polymeric Piles

Standard Specification for Polymeric Piles D7258-09 ASTM|D7258-09|en-US Standard Specification for Polymeric Piles Standard new BOS Vol. 08.03 Committee D20
$ 83.00 In stock

Abstract

This specification establishes the physical and performance requirements for round and rectangular cross-section polymeric piles in axial and lateral load-bearing applications including, by not limited to, marine, waterfront, and corrosive environments. It does not apply to individual polymeric pile products, sheet piles, and other mechanically connected polymeric pile products using inter-locking systems. Covered here are six types of polymeric piles that are fabricated from materials that may be virgin, recycled, or both, as long as the finished product meets all of the criteria specified herein. These types are: Type I, polymeric only; Type II, polymeric with reinforcement in the form of chopped, milled or continuous fiber or mineral; Type III, polymeric with reinforcement in the form of metallic bars, cages, or shapes; Type IV, polymeric with reinforcement in the form of non-metallic bars or cages; Type V, polymeric composite tube with a concrete core; and Type VI, any other polymeric piling meeting the requirements stated herein and not otherwise described by Types I through V. The polymeric tiles shall adhere to specified physical attributes such as size, cross-sectional shape, length, straightness, placement of reinforcement, and surface conditions. The performance requirements which pile specimens shall conform to include creep rupture, serviceability, flexural properties, shear strength, bearing strength, design flexural stiffness, energy absorption, compressive strength, combined stresses, dimensional stability (thermal expansion), hygrothermal cycling, and flame spread index.

Scope

1.1 This specification addresses the use of round and rectangular cross-section polymeric piles in axial and lateral load-bearing applications, including but not limited to marine, waterfront, and corrosive environments.

1.2 This specification is only applicable to individual polymeric pile products. Sheet pile and other mechanically connected polymeric pile products using inter-locking systems, are not part of this specification.

1.3 The piling products considered herein are characterized by the use of polymers, whereby (1) the pile strength or stiffness requires the inclusion of the polymer, or (2) a minimum of fifty percent (50 %) of the weight or volume is derived from the polymer. The type classifications of polymeric piles described in Section 4 show how they can be reinforced by composite design for increased stiffness or strength.

1.4 This specification covers polymeric piles fabricated from materials that are virgin, recycled, or both, as long as the finished product meets all of the criteria specified herein. Diverse types and combinations of inorganic filler systems are permitted in the manufacturing of polymeric piling products. Inorganic fillers include such materials as talc, mica, silica, wollastonite, calcium carbonate, etc. Pilings are often placed in service where they will be subjected to continuous damp or wet exposure conditions. Due to concerns of water sensitivity and possible affects on mechanical properties in such service conditions, organic fillers, including lignocellulosic materials such as those made or derived from wood, wood flour, flax shive, rice hulls, wheat straw, and combinations thereof, are not permitted in the manufacturing of polymeric piling products.

1.5 The values are stated in inch-pound units as these are currently the most common units used by the construction industry.

1.6 Polymeric piles under this specification are designed using design stresses determined in accordance with Test Methods D 6108, D 6109, and D 6112 and procedures contained within this specification unless otherwise specified.

1.7 Although in some instances it will be an important component of the pile design, frictional properties are currently beyond the scope of this document.

1.8 Criteria for design are included as part of this specification for polymeric piles. Certain Types and sizes of polymeric piles will be better suited for some applications than others. Polymeric piles designed and manufactured under the different Type classifications as defined within this specification will, as a whole, exhibit a wide-range of mechanical properties. For example, a 10-in. diameter Type II, chopped glass fiber reinforced high-density polyethylene (HDPE) pile will likely have an apparent stiffness much different than a 10-in. diameter Type V, glass fiber reinforced composite tube filled with concrete. Similarly, the ultimate moment capacity of these two example piles will also likely be significantly different from each other. Use of a licensed Professional Engineer is, therefore, highly recommended for designing and selecting polymeric piles in accordance with this specification.

1.9 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Note 1—There is no known ISO equivalent to this specification.

Price:
Contact Sales
Related
Reprints and Permissions
Reprints and copyright permissions can be requested through the
Copyright Clearance Center
Details
Book of Standards Volume: 08.03
Developed by Subcommittee: D20.20
Pages: 17
DOI: 10.1520/D7258-09
ICS Code: 83.140.99