Standard Historical Last Updated: May 03, 2018 Track Document
ASTM D7249/D7249M-16e1

Standard Test Method for Facing Properties of Sandwich Constructions by Long Beam Flexure

Standard Test Method for Facing Properties of Sandwich Constructions by Long Beam Flexure D7249_D7249M-16E01 ASTM|D7249_D7249M-16E01|en-US Standard Test Method for Facing Properties of Sandwich Constructions by Long Beam Flexure Standard new BOS Vol. 15.03 Committee D30
$ 68.00 In stock

Significance and Use

5.1 Flexure tests on flat sandwich construction may be conducted to determine the sandwich flexural stiffness, the core shear strength, and shear modulus, or the facings’ compressive and tensile strengths. Tests to evaluate core shear strength may also be used to evaluate core-to-facing bonds.

5.2 This test method is limited to obtaining the strength and stiffness of the sandwich panel facings, and to obtaining load-deflection data for use in calculating sandwich beam flexural and shear stiffness using Standard Practice D7250/D7250M. Due to the curvature of the flexural test specimen when loaded, facesheet compression strength from this test may not be equivalent to the facesheet compression strength of sandwich structures subjected to pure edgewise (in-plane) compression.

5.3 Core shear strength and shear modulus are best determined in accordance with Test Method C273 provided bare core material is available. Test Method C393 may also be used to determine core shear strength. Standard Practice D7250/D7250M may be used to calculate the flexural and shear stiffness of sandwich beams.

5.4 This test method can be used to produce facing strength data for structural design allowables, material specifications, and research and development applications; it may also be used as a quality control test for bonded sandwich panels.

5.5 Factors that influence the facing strength and shall therefore be reported include the following: facing material, core material, adhesive material, methods of material fabrication, facing stacking sequence and overall thickness, core geometry (cell size), core density, adhesive thickness, specimen geometry, specimen preparation, specimen conditioning, environment of testing, specimen alignment, loading procedure, speed of testing, facing void content, adhesive void content, and facing volume percent reinforcement. Further, facing strength may be different between precured/bonded and co-cured facesheets of the same material.

Note 2: Concentrated forces on beams with thin facings and low density cores can produce results that are difficult to interpret, especially close to the failure point. Wider loading blocks and rubber pressure pads may assist in distributing the forces.

Note 3: To ensure that simple sandwich beam theory is valid, a good rule of thumb for the four-point bending test is the span length divided by the sandwich thickness should be greater than 20 (L/d > 20) with the ratio of facing thickness to core thickness less than 0.1 (t/c < 0.1).


1.1 This test method covers determination of facing properties of flat sandwich constructions subjected to flexure in such a manner that the applied moments produce curvature of the sandwich facing planes and result in compressive and tensile forces in the facings. Permissible core material forms include those with continuous bonding surfaces (such as balsa wood and foams) as well as those with discontinuous bonding surfaces (such as honeycomb).

1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

1.2.1 Within the text, the inch-pound units are shown in brackets.

1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Note 1: Alternate procedures for determining the compressive strength of unidirectional polymer matrix composites materials in a sandwich beam configuration may be found in Test Method D5467/D5467M.

1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Contact Sales
Reprints and Permissions
Reprints and copyright permissions can be requested through the
Copyright Clearance Center
Book of Standards Volume: 15.03
Developed by Subcommittee: D30.09
Pages: 10
DOI: 10.1520/D7249_D7249M-16E01
ICS Code: 79.060.01