Standard Active Last Updated: Feb 12, 2024 Track Document
ASTM D5857-17(2024)

Standard Specification for Polypropylene Injection and Extrusion Materials Using ISO Protocol and Methodology

Standard Specification for Polypropylene Injection and Extrusion Materials Using ISO Protocol and Methodology D5857-17R24 ASTM|D5857-17R24|en-US Standard Specification for Polypropylene Injection and Extrusion Materials Using ISO Protocol and Methodology Standard new BOS Vol. 08.03 Committee D20
$ 76.00 In stock
ASTM International

Abstract

This specification covers polypropylene materials suitable for injection molding and extrusion. Polymers consist of polypropylene homopolymers, polypropylene copolymers, and polypropylene-elastomer compounds produced with or without the addition of impact modifiers (ethylene-propylene rubber, polyisobutylene rubber, and butyl rubber, and so forth), colorants, stabilizers, lubricants, fillers, or reinforcements. Unreinforced polypropylene materials are classified into groups in accordance with basic composition. These groups are subdivided into classes and grades. The plastic composition shall be uniform and shall conform to the requirements specified. Tests shall be performed to determine the properties of the material in accordance with the following test methods: flow rate; tensile strength; flexural modulus; Charpy impact resistance; falling mass impact resistance; temperature of deflection under load; and multiaxial impact ductile-brittle transition temperature.

Scope

1.1 This specification covers polypropylene materials suitable for injection molding and extrusion. Polymers consist of polypropylene homopolymers, polypropylene copolymers, and polypropylene-elastomer compounds produced with or without the addition of impact modifiers (ethylene-propylene rubber, polyisobutylene rubber, and butyl rubber, and so forth), colorants, stabilizers, lubricants, fillers, or reinforcements.

1.2 This specification allows for the use of those polypropylene materials that can be recycled, reconstituted, and reground, provided that the following conditions are met:

1.2.1 The requirements as stated in this specification and other ISO guidelines pertaining to these types of materials are met, and

1.2.2 The material has not been modified in any way to alter its conformance to food contact regulations or similar requirements.

1.3 The proportions of recycled, reconstituted, and regrind material used, as well as the nature and the amount of any contaminant, cannot be practically covered in this specification. It is the responsibility of the supplier and buyer of recycled, reconstituted, and regrind materials to ensure compliance.

1.4 The properties included in this classification system are those required to identify the compositions covered. Other requirements necessary to identify particular characteristics important to specialized applications can be specified by using the suffixes as given in Section 5 and those in Classification System D4000.

1.5 This classification system and specification are intended to provide a means of calling out polypropylene materials used in the fabrication of end items or parts. It is not intended for the selection of materials. Material selection can be made by those having expertise in the plastic field only after careful consideration of the design and the performance required of the part, the environment to which it will be exposed, the fabrication process to be employed, the costs involved, and the inherent properties of the material other than those covered by this specification.

1.6 The values stated in SI units are to be regarded as the standard.

1.7 The following precautionary caveat pertains only to the test methods portion, Section 13, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

Note 1: This specification is similar to both ISO 1873-1 and ISO 1873-2, but to different degrees. This specification resembles ISO 1873-1 in title only. The content is significantly different. This specification and ISO 1873-2 differ in approach or detail; data obtained using either are technically equivalent.

1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Price:
Contact Sales
Related
Reprints and Permissions
Reprints and copyright permissions can be requested through the
Copyright Clearance Center
Details
Book of Standards Volume: 08.03
Developed by Subcommittee: D20.15
Pages: 20
DOI: 10.1520/D5857-17R24
ICS Code: 83.040.20