Standard Historical Last Updated: Nov 07, 2023 Track Document
ASTM D4646-16

Standard Test Method for 24-h Batch-Type Measurement of Contaminant Sorption by Soils and Sediments

Standard Test Method for 24-h Batch-Type Measurement of Contaminant Sorption by Soils and Sediments D4646-16 ASTM|D4646-16|en-US Standard Test Method for 24-h Batch-Type Measurement of Contaminant Sorption by Soils and Sediments Standard new BOS Vol. 11.04 Committee D34
$ 75.00 In stock
ASTM International

Significance and Use

5.1 This test method is meant to allow for a rapid (24 h) index of a geomedia's sorption affinity for given solutes in environmental waters or leachates. A large number of samples may be run in parallel using this test method to determine a comparative ranking of those samples, based upon the amount of solute sorbed by the geomedia, or by various geomedia or leachate constituents. The 24-h time is used to make the test convenient and also to minimize microbial, light, or hydrolytic degradation which may be a problem in longer-timed procedures. While Kd values are directly applicable for screening and comparative ranking purposes, their use in predictive field applications generally requires the assumption that Kd be a fixed value.

5.2 While this test method may be useful in determining 24-h Kd values for nonvolatile organic constituents, interlaboratory testing has been carried out only for the nonvolatile inorganic species, arsenic and cadmium (see Section 12). However, the procedure has been tested for single laboratory precision with polychlorinated biphenyls (PCBs) and is believed to be useful for all stable and nonvolatile inorganic, and organic constituents. This test method is not considered appropriate for volatile constituents.

5.3 The 24-h time limit may be sufficient to reach a steady-state Kd; however, the calculated Kd value should be considered a non-equilibrium measurement unless steady-state has been determined. To report this determination as a steady-state Kd, this test method should be conducted for intermediate times (for example, 12, 18, and 22 h) to ensure that the soluble concentrations in the solution have reached a steady state by 24 h. If a test duration of greater than 24 h is required, refer to Test Method D4319 for an alternate procedure of longer duration.

Scope

1.1 This test method describes a procedure for determining the sorption affinity of waste solutes by unconsolidated geologic material in aqueous suspension. The waste solute may be derived from a variety of sources such as wells, underdrain systems, or laboratory solutions such as those produced by waste extraction tests like the Test Method D3987 shake extraction method.

1.2 This test method is applicable in screening and providing relative rankings of a large number of geomedia samples for their sorption affinity in aqueous leachate/geomedia suspensions. This test method may not simulate sorption characteristics that would occur in unperturbed geologic settings.

1.3 While this procedure may be applicable to both organic and inorganic constituents, care must be taken with respect to the stability of the particular constituents and their possible losses from solution by such processes as degradation by microbes, light, hydrolysis, or sorption to material surfaces. This test method should not be used for volatile chemical constituents (see 6.1).

1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Price:
Contact Sales
Related
Reprints and Permissions
Reprints and copyright permissions can be requested through the
Copyright Clearance Center
Details
Book of Standards Volume: 11.04
Developed by Subcommittee: D34.01.04
Pages: 5
DOI: 10.1520/D4646-16
ICS Code: 13.080.05