Standard Active Last Updated: Aug 06, 2020 Track Document
ASTM D3883-04(2020)

Standard Test Method for Yarn Crimp and Yarn Take-up in Woven Fabrics

Standard Test Method for Yarn Crimp and Yarn Take-up in Woven Fabrics D3883-04R20 ASTM|D3883-04R20|en-US Standard Test Method for Yarn Crimp and Yarn Take-up in Woven Fabrics Standard new BOS Vol. 07.01 Committee D13
$ 55.00 In stock

Significance and Use

5.1 The relationship of the length of a piece of fabric and the length of yarn in the fabric can be determined accurately only be measuring the length of yarn entering the loom and the length of fabric made from that particular length of yarn. In most cases, however, the determination must of necessity be made on a woven fabric by measuring the length of yarn removed from a measured length of fabric, thus introducing certain variations that will influence the accuracy of the test. Yarn removed from the woven fabric contains undulations or waves that have been introduced by the weaving process. Heat, moisture, and mechanical shrinkage on subsequent finishing operations may accentuate these undulations, and in all probability, increase the force to pull them out and straighten the yarn. In order to accurately measure the length of the yarn after the removal of the crimp, these undulations must be pulled out without elongating the yarn. In some cases, the minimum force necessary to straighten the yarn will cause a certain amount of the elongation to take place, thus increasing the length of the yarn. Also, stresses imposed upon the yarn during the weaving process may have been sufficient to stretch the yarn beyond its elastic limit, again increasing its length. It is recognized that determination made by measuring length of yarn removed from a measured length of fabric may tend to give crimp values that are somewhat higher than the crimp in the yarn as it lay in the fabric. In the case of fabrics made from yarns that exhibit differential shrinkage, or yarns of widely different count, or yarns woven at different tensions, the crimp of each type of yarn in the fabric must be determined and reported separately.

5.2 This test method can be used for acceptance testing of commercial shipments but comparisons should be made with caution because information on estimates of between-laboratory precision is limited as noted in 13.1.

5.2.1 If there are differences of practical significance between reported test results for two laboratories (or more), comparative tests should be performed to determine if their is a statistical bias between them, using competent statistical assistance. As a minimum, ensure the test samples to be used are as homogeneous as possible, are drawn from the material from which the disparate test results were obtained, and are randomly assigned in equal numbers to each laboratory for testing. The test results from the two laboratories should be compared using a statistical test for unpaired data, at a probability level chosen prior to the testing series. If a bias is found, either its cause must be found and corrected, or future test results for that material must be adjusted in consideration of the known bias.


1.1 This test method covers the determination of the relationship between the length of a piece of fabric and the length of the yarn in the fabric by measurement of the yarn crimp and yarn take-up.

1.2 This test method applies to woven fabrics.

1.3 The values stated in either SI or inch-pound units are to be regarded separately as standard. Within the text, the inch-pound units are shown in parentheses. The values stated in each system are not exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the specification.

1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Contact Sales
Reprints and Permissions
Reprints and copyright permissions can be requested through the
Copyright Clearance Center
Book of Standards Volume: 07.01
Developed by Subcommittee: D13.59
Pages: 4
DOI: 10.1520/D3883-04R20
ICS Code: 59.080.30