Standard Active Last Updated: Jun 18, 2024 Track Document
ASTM D2495-07(2024)

Standard Test Method for Moisture in Cotton by Oven-Drying

Standard Test Method for Moisture in Cotton by Oven-Drying D2495-07R24 ASTM|D2495-07R24|en-US Standard Test Method for Moisture in Cotton by Oven-Drying Standard new BOS Vol. 07.01 Committee D13
$ 69.00 In stock
ASTM International

Significance and Use

5.1 This test method for testing the moisture content of cotton can be used for acceptance testing of commercial shipments of lint cotton provided the between-laboratory bias is known.

5.1.1 If there are differences or practical significance between reported test results for two laboratories, or more, comparative test should be performed to determine if there is a statistical bias, using competent statistical assistance. As a minimum, use test samples as homogeneous as possible, drawn from the material from which the disparate test results are obtained, and assigned randomly in equal numbers to each laboratory for testing. Other materials with established test values may be used for this purpose. Compare the test results from the two laboratories using a statistical test for unpaired data at a probability level chosen prior to the testing series. If a bias is found, either its cause must be found and corrected, or future test results must be adjusted in consideration of the known bias.

5.2 Information on the moisture content of cotton is desirable since the physical properties of cotton are significantly affected by its moisture content. High moisture content increases flexibility, toughness, elongation, and tensile strength. Too high a moisture content causes difficulty in processing due to the tendency of the stock to “lap-up” on drafting rolls. Low moisture, on the other hand, facilitates cleaning but increases the brittleness of the fiber and results in fiber breakage during ginning, cleaning, and mill processing. Low moisture also increases fly waste and may cause manufacturing difficulties due to static electricity.

5.3 Variations in the amount of moisture present affect the mass and hence the market value of a lot of material sold at a definite price per unit mass. Knowledge of the moisture content or regain can be accordingly an important financial consideration.

5.4 Moisture content variation affects lap, sliver, and roving linear density which in turn controls yarn number variation.

5.5 The mass of the oven-dry specimen used in this method is the mass observed after the specimen has been dried in an oven supplied with ambient air. The observed mass is accordingly subject to minor variations. These variations, however, are believed to be without significance in commercial transactions.

Scope

1.1 This test method covers the determination of the amount of moisture in cotton by oven-drying and is applicable to raw cotton, cotton stock in process, and cotton waste.

1.2 This test method may also, by agreement, be used for determining moisture in blends of cotton with other fibers.

1.3 This test method offers alternative procedures for weighing the dried specimens, one procedure using an oven balance (9.3) and the other using a desiccator (9.4).

Note 1: For other methods of determination of moisture in textile materials refer to Test Method D2654, which includes two options based on drying in an oven, and one option based on distillation with an immiscible solvent: Test Methods D885/D885M, Test Method D1576, Test Method D2462.

1.4 The values stated in SI units are to be regarded as the standard. No other units are included in this standard.

1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Price:
Contact Sales
Related
Reprints and Permissions
Reprints and copyright permissions can be requested through the
Copyright Clearance Center
Details
Book of Standards Volume: 07.01
Developed by Subcommittee: D13.11
Pages: 5
DOI: 10.1520/D2495-07R24
ICS Code: 59.060.10