Standard Active Last Updated: Jul 03, 2020 Track Document
ASTM C1564-20

Standard Guide for Use of Silicone Sealants for Protective Glazing Systems

Standard Guide for Use of Silicone Sealants for Protective Glazing Systems C1564-20 ASTM|C1564-20|en-US Standard Guide for Use of Silicone Sealants for Protective Glazing Systems Standard new BOS Vol. 04.07 Committee C24
$ 63.00 In stock
ASTM International

Significance and Use

4.1 Guidelines are provided for the use of silicone sealants in protective glazing. Protective glazing incorporates various forms of glazing that are not covered in Guides C1401 and C1193. The requirements for a sealant in protective glazing are similar to the requirements for structural sealant glazing. However, for certain applications, such as missile impact and blast resistant glazing, sealant requirements may be greater. Modes of failure for blast resistant glazing can be different than the modes of failure for missile impact glazing. Of particular concern is the outbound glazing support loading from blast wave negative phase pressure or the dynamic rebound of the glazing, or both.

4.2 Many types of protective glazing systems are relatively new and the test methods and standards for protective glazing are continually evolving. Because the demands on a sealant in protective glazing systems are changing, guidelines are necessarily general in many instances.

4.3 As a component of a glazing system, the sealant can be a factor in whether a glazing system meets the requirements of a specific test method but other factors such as the frame and glazing type, may be of greater influence.

4.4 The designer of a protective glazing system should consult with the various manufacturers of the component materials. The experience and judgment of the glazing system designer working with the sealant manufacturer and other component manufacturers, can ultimately determine whether a specific glazing system will successfully meet a specific test requirement.


1.1 This guide covers the use of silicone sealants in protective glazing systems for building construction. Protective glazing includes systems designed for use in applications subject to natural hazards, such as hurricanes, earthquakes, windstorms, impacts from wind-borne debris; and assaults such as burglary, air blasts, forced-entry attacks and ballistic attacks.

1.2 While other glazing accessories and components are used in protective glazing, this document specifically describes the use of silicone sealants for protective glazing systems.

1.3 This guide provides information useful to design professionals, architects, manufacturers, installers, and others for the design and use of silicone sealants for protective glazing systems.

1.4 A silicone sealant is only one component of a glazing system. A glazing system that meets the testing and code requirement for protective glazing must successfully integrate the frame and its anchorage, glass, or other glazing materials, protective film or interlayer and silicone sealant into a high performance system. Compliance with code or other requirements can be determined through physical testing of the glazing system or through computer simulation.

1.5 Glazing systems using silicone sealants that have successfully met the test requirements for missile impact and airblast test requirements incorporate the use of silicone sealants specifically formulated, tested, and marketed for this application. Sealants that are commonly used today comply with Specifications C920 and C1184.

1.6 This guide does not discuss sealants intended to protect against radioactivity or provide biological containment.

1.7 The committee with jurisdiction over this standard is not aware of any comparable standards published by other organizations.

1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.9 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Contact Sales
Reprints and Permissions
Reprints and copyright permissions can be requested through the
Copyright Clearance Center
Book of Standards Volume: 04.07
Developed by Subcommittee: C24.10
Pages: 9
DOI: 10.1520/C1564-20
ICS Code: 71.100.55