Standard Active Last Updated: Nov 19, 2019 Track Document
ASTM C779/C779M-19

Standard Test Method for Abrasion Resistance of Horizontal Concrete Surfaces

Standard Test Method for Abrasion Resistance of Horizontal Concrete Surfaces C0779_C0779M-19 ASTM|C0779_C0779M-19|en-US Standard Test Method for Abrasion Resistance of Horizontal Concrete Surfaces Standard new BOS Vol. 04.02 Committee C09
$ 69.00 In stock

Significance and Use

4.1 The three test methods provide simulated abrasion conditions, which can be used to evaluate the effects on abrasion resistance of concrete, concrete materials, and curing or finishing procedures. They may also be used for quality acceptance of products and surface exposed to wear. They are not intended to provide a quantitative measurement of length of service.

4.2 The equipment used by each of these procedures is portable and thus suitable for either laboratory or field testing. The three procedures determine the relative wear of concrete surfaces as follows:

4.2.1 Procedure A—The revolving-disk machine operates by sliding and scuffing of steel disks in conjunction with abrasive grit.

4.2.2 Procedure B—The dressing-wheel machine operates by impact and sliding friction of steel dressing wheels.

4.2.3 Procedure C—The ball-bearing machine operates by high-contact stresses, impact, and sliding friction from steel balls.

Note 2: Diagrams of three machines meeting these specifications are shown in Fig. 1, Fig. 2, and Fig. 3.4

FIG. 1 Revolving Disks Abrasion Test Machine

 Revolving Disks Abrasion Test Machine Revolving Disks Abrasion Test Machine

FIG. 2 Dressing Wheel Abrasion Test Machine

 Dressing Wheel Abrasion Test Machine Dressing Wheel Abrasion Test Machine

FIG. 3 Ball Bearing Abrasion Test Machine

 Ball Bearing Abrasion Test Machine Ball Bearing Abrasion Test Machine

Scope

1.1 This test method covers three procedures for determining the relative abrasion resistance of horizontal concrete surfaces. The procedures differ in the type and degree of abrasive force they impart, and are intended for use in determining variations in surface properties of concrete affected by mixture proportions, finishing, and surface treatment. They are not intended to provide a quantitative measurement of the length of service that may be expected from a specific surface.

1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the inch-pound units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of each other.

1.3 The text of this standard references notes and footnotes that provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of this standard.

1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. (Warning—Fresh hydraulic cementitious mixtures are caustic and may cause chemical burns to skin and tissue upon prolonged exposure.2)

Note 1: Other procedures are available for measuring the abrasion resistance of concrete surfaces in addition to the three procedures contained in this test method. Consideration should be given to Test Methods C944/C944M and C418. The test method most closely representing service conditions should be used.

1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Price:
Contact Sales
Related
Reprints and Permissions
Reprints and copyright permissions can be requested through the
Copyright Clearance Center
Details
Book of Standards Volume: 04.02
Developed by Subcommittee: C09.62
Pages: 6
DOI: 10.1520/C0779_C0779M-19
ICS Code: 91.100.30