Standard Active Last Updated: Jun 17, 2020 Track Document
ASTM C749-15(2020)

Standard Test Method for Tensile Stress-Strain of Carbon and Graphite

Standard Test Method for Tensile Stress-Strain of Carbon and Graphite C0749-15R20 ASTM|C0749-15R20|en-US Standard Test Method for Tensile Stress-Strain of Carbon and Graphite Standard new BOS Vol. 05.05 Committee D02
$ 76.00 In stock

Significance and Use

5.1 The round robin testing on which the precision and bias for this test method have been determined employed a range of graphites (see Table 2) whose grain sizes were of the order of 1 mil to 1/4 in. (0.0254 mm to 6.4 mm) and larger. This wide range of carbons and graphites can be tested with uniform gauge diameters with minimum parasitic stresses to provide quality data for use in engineering applications rather than simply for quality control. This test method can be easily adapted to elevated temperature testing of carbons and graphites without changing the specimen size or configuration by simply utilizing elevated temperature materials for the load train. This test method has been utilized for temperatures as high as 4352 °F (2400 °C). The design of the fixtures (Figs. 2-9 and Table 1) and description of the procedures are intended to bring about, on the average, parasitic stresses of less than 5 %. The specimens for the different graphites have been designed to ensure fracture within the gauge section commensurate with experienced variability in machining and testing care at different facilities. The constant gauge diameter permits rigorous analytical treatment.

Note 1: Refer to Fig. 2, Items 101 and 115.

Note 1: Refer to Fig. 2, Items 103 and 117.

(A) Screw size.

Note 1: Refer to Fig. 2, Items 107, 109, 111, 113, 121, 123, and 129.

Note 1: Refer to Fig. 2, Items 105, 109, 113, 119, 123, 125, and 129.

Note 1: Refer to Fig. 2, Items 108, 112, 122, and 128.

FIG. 9 Attachment for Strain Flags or Extensometers to Provide Minimum Damage to Surface of Specimen

Attachment for Strain Flags or Extensometers to Provide Minimum Damage to Surface of SpecimenAttachment for Strain Flags or Extensometers to Provide Minimum Damage to Surface of Specimen

Note 1: Jig align to ensure precision gauge length; mount post or groove to match type of extensometer.

5.2 Carbon and graphite materials exhibit significant physical property differences within parent materials. Exact sampling patterns and grain orientations must be specified in order to make meaningful tensile strength comparisons. See also Test Methods C565.

Scope

1.1 This test method covers the testing of carbon and graphite in tension to obtain the tensile stress-strain behavior, to failure, from which the ultimate strength, the strain to failure, and the elastic moduli may be calculated as may be required for engineering applications. Table 2 lists suggested sizes of specimens that can be used in the tests.

Note 1: The results of about 400 tests, on file at ASTM as a research report, show the ranges of materials that have been tested, the ranges of specimen configurations, and the agreement between the testers. See Section 11.

Note 2: For safety considerations, it is recommended that the chains be surrounded by suitable members so that at failure all parts of the load train behave predictably and do not constitute a hazard for the operator.

1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. Conversions are not provided in the tables and figures.

1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Price:
Contact Sales
Related
Reprints and Permissions
Reprints and copyright permissions can be requested through the
Copyright Clearance Center
Details
Book of Standards Volume: 05.05
Developed by Subcommittee: D02.F0
Pages: 11
DOI: 10.1520/C0749-15R20
ICS Code: 71.060.10