Standard Active Last Updated: Jun 28, 2023 Track Document
ASTM C183/C183M-23

Standard Practice for Sampling and the Amount of Testing of Hydraulic Cement

Standard Practice for Sampling and the Amount of Testing of Hydraulic Cement C0183_C0183M-23 ASTM|C0183_C0183M-23|en-US Standard Practice for Sampling and the Amount of Testing of Hydraulic Cement Standard new BOS Vol. 04.01 Committee C01
$ 63.00 In stock
ASTM International

Significance and Use

4.1 The sampling procedures described are intended for use in the procurement of samples of hydraulic cement after it has been manufactured and is ready to be offered for sale. They are not intended as sampling procedures for quality control purposes during manufacturing. The testing procedures outlined cover the amount of testing to be done and provide guidance for reporting on conformance or non-conformance of cements with requirements of purchase specifications.

4.2 This practice is referenced as the procedure for sampling natural cement (Specification C10/C10M), masonry cement (Specification C91/C91M), portland cement (Specification C150/C150M), blended hydraulic cement (Specification C595/C595M), expansive hydraulic cement (Specification C845/C845M), hydraulic cement based on a performance specification (Specification C1157/C1157M), plastic stucco cement (Specification C1328/C1328M), and mortar cement (Specification C1329/C1329M), and

4.3 Most building codes and construction specifications require that hydraulic cement to be used in the work meet the applicable requirements of the relevant purchase specifications, such as Specifications C10/C10M, C91/C91M, C150/C150M, C595/C595M, C1157/C1157M, C1328/C1328M, C1329/C1329M, or C845/C845M. If the code or specification requires sampling of the manufactured cement, the provisions given in 4.4 are applicable. Not much cement is sold on the basis of such sampling and testing. A useful discussion of sampling and testing cement is contained in ACI 225.1R.

4.4 The procedures covered in this practice should be done by or for purchasers of hydraulic cement who are using a code or specification that requires sampling and testing to determine if the samples conform to the relevant acceptance specifications. The testing is done using specified methods to determine whether the samples yield test results that conform to the specification, and the tests serve as a basis for acceptance or rejection of the lot of material sampled.

4.5 It is neither intended nor required that all cements be tested using all the test methods referenced in Section 2.


1.1 This practice covers procedures for sampling and for the amount of testing of hydraulic cement after it has been manufactured and is ready to be offered for sale.

1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. Values in SI units [or inch-pound units] shall be obtained by measurement in SI units [or inch-pound units] or by appropriate conversion, using the Rules for Conversion and Rounding given in Standard IEEE/ASTM SI 10, Values are stated in only SI units when inch-pound units are not used in practice

1.3 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered requirements of the standard.

1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Contact Sales
Reprints and Permissions
Reprints and copyright permissions can be requested through the
Copyright Clearance Center
Book of Standards Volume: 04.01
Developed by Subcommittee: C01.95
Pages: 9
DOI: 10.1520/C0183_C0183M-23
ICS Code: 91.100.10