Standard Active Last Updated: Jul 19, 2024 Track Document
ASTM B888/B888M-24

Standard Specification for Copper Alloy Strip for Use in Manufacture of Electrical Connectors or Spring Contacts

Standard Specification for Copper Alloy Strip for Use in Manufacture of Electrical Connectors or Spring Contacts B0888_B0888M-24 ASTM|B0888_B0888M-24|en-US Standard Specification for Copper Alloy Strip for Use in Manufacture of Electrical Connectors or Spring Contacts Standard new BOS Vol. 02.01 Committee B05
$ 76.00 In stock
ASTM International

Abstract

This specification establishes the requirements for copper alloy strips for use in the manufacture of electrical connectors or spring contacts produced from one of the following Copper Alloy UNS Nos.: C14530, C15100, C15500, C17000, C17200, C17410, C17450, C17460, C17500, C17510, C19010, C19025, C19210, C19400, C19500, C19700, C23000, C26000, C40810, C40850, C40860, C42200, C42500, C42520, C42600, C50580, C50780, C51000, C51080, C51100, C51180, C51980, C52100, C52180, C52480, C63800, C65400, C68800, C70250, C70260, C70265, C75200, and C76200. The material for manufacture shall be a cast bar, slab, cake, billet, or other form of such composition as to be suitable for processing by either hot- or cold-working to produce the products prescribed in this specification. Products shall be finished by hot working, cold working, annealing, or heat treatment as may be necessary to meet mechanical property requirements, which include tensile strength, yield strength, and elongation. Tempers shall be available in the annealed, rolled, or mill hardened conditions. Products shall also adhere to tolerances as to dimension such as thickness, width, length, straightness, and mass.

Scope

1.1 This specification covers the requirements for copper alloy strip for use in the manufacture of electrical connectors or spring contacts produced from one of the following Copper Alloy UNS Nos.:2 C14530, C15100, C15500, C17000, C17200, C17410, C17450, C17460, C17500, C17510, C19002, C19010, C19015, C19025, C19210, C19400, C19500, C19700, C23000, C26000, C40810, C40850, C40860, C42200, C42500, C42520, C42600, C50580, C50780, C51000, C51080, C51100, C51180, C51980, C52100, C52180, C52480, C63800, C64725, C65400, C68800, C70250, C70260, C70265, C70310, C70350, C75200, and C76200.

1.2 The requirements for the other copper alloys such as copper-nickel-tin spinodal, UNS C72650, C72700, and C72900, shall be as prescribed in the current edition of Specification B740.

1.3 Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not necessarily be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

1.4 The following safety hazard caveat pertains only to the test methods described in this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Price:
Contact Sales
Related
Reprints and Permissions
Reprints and copyright permissions can be requested through the
Copyright Clearance Center
Details
Book of Standards Volume: 02.01
Developed by Subcommittee: B05.01
Pages: 13
DOI: 10.1520/B0888_B0888M-24
ICS Code: 29.050