Standard Historical Last Updated: Apr 18, 2019 Track Document
ASTM B829-18

Standard Specification for General Requirements for Nickel and Nickel Alloys Seamless Pipe and Tube

Standard Specification for General Requirements for Nickel and Nickel Alloys Seamless Pipe and Tube B0829-18 ASTM|B0829-18|en-US Standard Specification for General Requirements for Nickel and Nickel Alloys Seamless Pipe and Tube Standard new BOS Vol. 02.04 Committee B02
$ 75.00 In stock


This general specification contains the mandatory requirements to the ASTM standards listed herein for seamless pipes and tubes made from nickel and nickel alloys. In case of conflict, the requirements listed in the particular product specification takes precedence over those listed here.


1.1 This specification contains various requirements that, with the exception of Sections 5 and 10, are mandatory requirements to the following ASTM nickel and nickel alloy, seamless pipe and tube specifications:

Title of Specification


Nickel Seamless Pipe and Tube


Seamless Nickel and Nickel Alloy, Condenser and Heat Ex-
 changer Tubes


Nickel-Copper Alloy (UNS N04400) Seamless Pipe and Tube


Nickel-Chromium-Iron Alloys (UNS N06600, N06601, and
 N06690) Seamless Pipe and Tube


Nickel-Iron-Chromium Alloy Seamless Pipe and Tube


Nickel-Iron-Chromium-Molybdenum-Copper Alloy (UNS N08825
 and N08221) Seamless Pipe and Tube


Nickel-Chromium-Molybdenum-Columbium Alloys (UNS
 N06625) Pipe and Tube


Nickel-Chromium-Iron-Columbium-Molybdenum-Tungsten Alloy
 (UNS N06102) Seamless Pipe and Tube


Nickel-Iron-Chromium-Silicon Alloys (UNS N08330 and UNS
 N08332) Seamless Pipe


Copper-Beryllium Alloy Forgings and Extrusion


Seamless Nickel and Nickel-Cobalt Alloy Pipe and Tube


UNS N08028 Seamless Tubes


UNS N08904, UNS N08925 and UNS N08926 Seamless Pipe
 and Tube


Iron-Nickel-Chromium-Molybdenum Alloys (UNS N08366 and
 UNS N08367) Seamless Pipe and Tube


Ni-Cr-Mo-Co-W-Fe-Si Alloy (UNS N06333) Seamless Pipe and


Seamless UNS N08020, UNS N08026, and UNS N08024
 Nickel-Alloy Pipe and Tube


1.2 One or more of the test requirements of Section 5 apply only if specifically stated in the product specification or in the purchase order.

1.3 In case of conflict between a requirement of the product specification and a requirement of this general specification, only the requirement of the product specification needs to be satisfied.

1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

1.5 The following safety hazards caveat pertains only to the test requirements portion, Section 5, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use.

1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Contact Sales
Reprints and Permissions
Reprints and copyright permissions can be requested through the
Copyright Clearance Center
Book of Standards Volume: 02.04
Developed by Subcommittee: B02.07
Pages: 6
DOI: 10.1520/B0829-18
ICS Code: 23.040.15