Standard Historical Last Updated: Apr 06, 2018 Track Document
ASTM B111/B111M-16

Standard Specification for Copper and Copper-Alloy Seamless Condenser Tubes and Ferrule Stock

Standard Specification for Copper and Copper-Alloy Seamless Condenser Tubes and Ferrule Stock B0111_B0111M-16 ASTM|B0111_B0111M-16|en-US Standard Specification for Copper and Copper-Alloy Seamless Condenser Tubes and Ferrule Stock Standard new BOS Vol. 02.01 Committee B05
$ 91.00 In stock

Abstract

This specification establishes the requirements for seamless tube and ferrule stock of copper and various copper alloys of a specified range of diameters, for use in surface condensers, evaporators, and heat exchangers. The specified coppers and copper alloys are UNS No. C10100, C10200, C10300, C10800, C12000, C12200, C14200, C19200, C23000, C28000, C44300, C44400, C44500, C60800, C61300, C61400, C68700, C70400, C70600, C70620, C71000, C71500, C71520, C71640, and C72200. The product shall be produced by processes such as casting, extrusion, drawing, annealing, straightening, trimming, and other processes which may produce a seamless tube in the specified condition. The coppers and copper alloys shall be specifically furnished in any one of the following tempers: annealed, light-drawn, hard-drawn, or hard drawn and end annealed. Tubes for ferrule stock shall be annealed sufficiently to be fully crystallized. Some tubes are suggested to be subjected to a stress-relieving thermal treatment subsequent to straightening. The products shall be subjected to expansion, flattening, and residual stress tests. The tensile and expansion requirements for the products are specified in accordance with the temper designation. The products shall also be subjected to mercurous nitrate, ammonia vapor, Eddy-current, hydrostatic, and pneumatic tests.

Scope

1.1 This specification2 establishes the requirements for seamless tube and ferrule stock of copper and various copper alloys up to 31/8 in. [80 mm] inclusive, in diameter, for use in surface condensers, evaporators, and heat exchangers. The following coppers and copper alloys are specified:3

Copper or Copper
Alloy UNS No.

Previously Used
Designation

Description

C10100

OFE

Oxygen-free electronic

C10200

OFA

Oxygen-free without residual deoxidants

C10300

. . .

Oxygen-free, extra low phosphorus

C10800

. . .

Oxygen-free, low phosphorus

C12000

DLPA

Phosphorized, low residual phosphorus

C12200

DHPA

Phosphorized, high residual phosphorus

C14200

DPAA

Phosphorized, arsenical

C19200

. . .

Phosphorized, 1 % iron

C23000

. . .

Red Brass

C28000

. . .

Muntz Metal

C44300

. . .

Admiralty Metals, B, C, and D

C44400

. . .

. . .

C44500

. . .

. . .

C60800

. . .

Aluminum Bronze

C61300

. . .

. . .

C61400

. . .

Aluminum Bronze, D

C68700

. . .

Aluminum Brass, B

C70400

. . .

95-5 Copper-Nickel

C70600

. . .

90-10 Copper-Nickel

C70620

. . .

90-10 Copper-Nickel—Welding Grade

C71000

. . .

80-20 Copper-Nickel

C71500

. . .

70-30 Copper-Nickel

C71520

. . .

70-30 Copper-Nickel—Welding Grade

C71640

. . .

Copper-nickel-iron-manganese

C72200

. . .

. . .

(A) Designations listed in Classification B224.

1.2 Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

1.3 The following safety hazards caveat pertains only to the test methods portion, Section 19, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. (Warning—Mercury has been designated by many regulatory agencies as a hazardous substance that can cause serious medical issues. Mercury, or its vapor, has been demonstrated to be hazardous to health and corrosive to materials. Caution should be taken when handling mercury and mercury containing products. See the applicable product Safety Data Sheet (SDS) for additional information. Users should be aware that selling mercury and/or mercury containing products in your state or country may be prohibited by law.)

Price:
Contact Sales
Related
Reprints and Permissions
Reprints and copyright permissions can be requested through the
Copyright Clearance Center
Details
Book of Standards Volume: 02.01
Developed by Subcommittee: B05.04
Pages: 12
DOI: 10.1520/B0111_B0111M-16
ICS Code: 23.040.15