Standard Historical Last Updated: Oct 28, 2019 Track Document
ASTM B103/B103M-15

Standard Specification for Phosphor Bronze Plate, Sheet, Strip, and Rolled Bar

Standard Specification for Phosphor Bronze Plate, Sheet, Strip, and Rolled Bar B0103_B0103M-15 ASTM|B0103_B0103M-15|en-US Standard Specification for Phosphor Bronze Plate, Sheet, Strip, and Rolled Bar Standard new BOS Vol. 02.01 Committee B05
$ 83.00 In stock

Abstract

This specification covers plate, rolled bar, sheet, and strip of copper-tin alloy (phosphor bronze plate), copper-tin-lead alloy (leaded phosphor bronze), and copper-tin-lead-zinc alloy (bearing bronze). Copper alloys covered include UNS Nos. C51000, C51100, C51180, C51900, C52100, C52180, C52400, C53400, and C54400. Product shall be manufactured by hot or cold working, rolling, and annealing. Chemical composition of the materials shall conform to UNS designation of the material. Product shall conform to chemical analysis, tensile strength and Rockwell hardness tests specified in the specification. Chemical composition testing shall be performed for each element, namely, copper, iron, lead, phosphorus, tin, and zinc. Tension test shall be made so that the longitudinal axis of the specimen is parallel to direction of rolling.

Scope

1.1 This specification establishes the requirements for copper-tin alloy (phosphor bronze), copper-tin-lead alloy (leaded phosphor bronze), and copper-tin-lead-zinc alloy (bearing bronze), plate, sheet, strip, and rolled bar. The phosphor bronzes commonly are used for deep drawing into bellows and stamping and forming into spring devices and into terminals and connectors for electrical apparatus because they combine high strength with high elongation. The leaded phosphor bronzes are used where strength, corrosion resistance, and machinability are required. The bearing bronze is used in bushings, bearings, and load-bearing thrust washers. The following alloys are covered:

Copper Alloy UNS No.2

Nominal Composition, %

Previously Used Designation

Copper

Tin

Zinc

Lead

 

 

 

 

 

 

C51000

95

5

. . .

. . .

A1

C51100

96

4

. . .

. . .

A 

C51180

96

4

. . .

. . .

. . .

C51900

94

6

. . .

. . .

 

 C52100A

92

8

. . .

. . .

C 

C52180

92

8

. . .

. . .

. . .

C52400

90

10 

. . .

. . .

D 

C53400

94

5

. . .

1

B1

C54400

88

4

3

4

B2

(A) SAE Specification CA 521 conforms to the requirements of UNS No. C52100.

Note 1: All of the above alloys contain small amounts of phosphorus, used as a deoxidant in melting, and to enhance the mechanical properties.

1.2 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

1.3 The following safety hazard caveat pertains only to the test method(s) described in this specification.

1.3.1 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Price:
Contact Sales
Related
Reprints and Permissions
Reprints and copyright permissions can be requested through the
Copyright Clearance Center
Details
Book of Standards Volume: 02.01
Developed by Subcommittee: B05.01
Pages: 7
DOI: 10.1520/B0103_B0103M-15
ICS Code: 77.150.30