Standard Active Last Updated: Jul 11, 2022 Track Document
ASTM A1122/A1122M-22

Standard Test Method for Bend Testing of Metallic-Coated Steel Sheet to Evaluate Coating Adhesion

Standard Test Method for Bend Testing of Metallic-Coated Steel Sheet to Evaluate Coating Adhesion A1122_A1122M-22 ASTM|A1122_A1122M-22|en-US Standard Test Method for Bend Testing of Metallic-Coated Steel Sheet to Evaluate Coating Adhesion Standard new BOS Vol. 01.06 Committee A05
$ 61.00 In stock

Significance and Use

4.1 This test method provides a standard method to bend the product to verify good coating, adhesion free of delamination, on metallic-coated steel sheet products under the jurisdiction of ASTM Committee A05 and its subcommittees as designated by a purchaser in a purchase order or contract.

4.1.1 Metallic coated coupons are bent 180° around progressively more thicknesses of metal, the end point being when failures no longer occur. The bend area is examined without magnification after each bend in order to determine coating fracture and loss of adhesion.

4.1.2 If desired, further examination of loss of adhesion or pickoff can be determined by performing a tape pull-off test subsequent to bending.

4.1.3 The material condition at the time of testing, sampling frequency, specimen location and orientation, minimum t-bend rating exhibiting no delamination or pick-off, reporting requirements, and other test parameters are contained in the pertinent material specification or in a general requirement specification for the particular product form. References are provided to the appropriate ASTM standards.

4.2 For this test method to successfully evaluate coating adhesion, the metal substrate must be capable of withstanding the bending operation without fracturing.

4.3 Coating adhesion is a significant quality characteristic of metallic coated steel sheet products. This test method employs the relevant t-bend rating specified in the referenced product standards to quickly determine if the metallic coating is free of delamination on the outside of a bend specimen. This is critical in ascertaining product conformance to specifications.

4.4 This test method is similar to, and uses some of the same apparatus as, Test Method D4145, which determines a t-bend rating for flexibility and adhesion of organic coatings (paints) on metallic substrates.

4.5 This test method may be used by other ASTM Committees and other standards writing bodies for the purpose of conformance testing.

Scope

1.1 This test method covers a bend test to verify that metallic coatings on steel sheet are free of delamination. The test method described is designed and intended for use in both laboratory and plant situations and their environments.

1.2 The metallic-coated steel product shall conform to all the requirements of the appropriate specifications as follows: Specifications A463/A463M, A653/A653M, A755/A755M, A792/A792M, A875/A875M, A924/A924M, A929/A929M, A1046/A1046M, A1057/A1057M, A1063/A1063M, A1079, and A1087/A1087M.

1.3 Quantitative limits are not addressed and are established in the general requirements, or individual product specifications, or both; or when applicable, as agreed to between supplier and user.

1.4 Units—This specification is applicable to orders in either inch-pound units or SI units. Values in inch-pound and SI units are not necessarily equivalent. Within the text, SI units are shown in brackets. Each system shall be used independently of the other.

1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Price:
Contact Sales
Related
Reprints and Permissions
Reprints and copyright permissions can be requested through the
Copyright Clearance Center
Details
Book of Standards Volume: 01.06
Developed by Subcommittee: A05.07
Pages: 4
DOI: 10.1520/A1122_A1122M-22
ICS Code: 25.220.40