Standard Active Last Updated: Oct 12, 2018
ASTM A1016/A1016M-18a

Standard Specification for General Requirements for Ferritic Alloy Steel, Austenitic Alloy Steel, and Stainless Steel Tubes

Standard Specification for General Requirements for Ferritic Alloy Steel, Austenitic Alloy Steel, and Stainless Steel Tubes
$ 63.00 In stock


This specification covers general requirements for ferritic alloy steel, austenitic alloy steel, and stainless steel tubes. The steel shall made by any process. The material shall conform to the tensile property requirements prescribed in the individual product specification. Yield strength tests and elongation tests shall be made to conform to the requirements. Flattening test, reverse flattening test, reverse bend test, flaring test, flange test, hardness test, ultrasonic test, eddy current test, flux leakage test, and hydrostatic test shall be made to conform to the requirements specified.


1.1 This specification covers a group of requirements that, unless otherwise specified in an individual specification, shall apply to the ASTM product specifications noted below.

Title of Specification




Seamless Carbon-Molybdenum Alloy-Steel Boiler and
 Superheater Tubes


Seamless Ferritic and Austenitic Alloy-Steel Boiler, Superheater,
 and Heat-Exchanger Tubes


Welded Austenitic Steel Boiler, Superheater, Heat-Exchanger,
 and Condenser Tubes


Electric-Resistance-Welded Ferritic Alloy-Steel Boiler and
 Superheater Tubes


Seamless and Welded Ferritic and Martensitic Stainless Steel
 Tubing for General Service


Seamless and Welded Austenitic Stainless Steel Tubing for
 General Service


Seamless and Welded Austenitic and Ferritic/Austenitic
 Stainless Steel Sanitary Tubing


Seamless and Welded Carbon and Alloy-Steel Tubes for
 Low-Temperature Service


Welded Austenitic Stainless Steel Feedwater Heater Tubes


Austenitic Stainless Steel Tubing for Breeder Reactor Core


Seamless and Welded Ferritic/Austenitic Stainless Steel Tubing
 for General Service


Seamless and Welded Ferritic Stainless Steel Feedwater Heater


Seamless Austenitic and Martensitic Stainless Steel Duct
 Tubes for Liquid Metal-Cooled Reactor Core Components


High-Frequency Induction Welded, Unannealed, Austenitic
 Steel Condenser Tubes


Welded Austenitic Alloy Steel Boiler, Superheater, Condenser,
 and Heat Exchanger Tubes with Textured Surface(s)


1.2 In the case of conflict between a requirement of a product specification and a requirement of this general requirements specification, the product specification shall prevail. In the case of conflict between a requirement of the product specification or a requirement of this general requirements specification and a more stringent requirement of the purchase order, the purchase order shall prevail.

1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. The inch-pound units shall apply unless the “M” designation (SI) of the product specification is specified in the order.

1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Contact Sales
Reprints and Permissions
Reprints and copyright permissions can be requested through the
Copyright Clearance Center
Book of Standards Volume: 01.01
Developed by Subcommittee: A01.10
Pages: 12
DOI: 10.1520/A1016_A1016M-18A
ICS Code: 77.140.20