Standard Active Last Updated: Sep 22, 2023 Track Document
ASTM A999/A999M-23

Standard Specification for General Requirements for Alloy and Stainless Steel Pipe

Standard Specification for General Requirements for Alloy and Stainless Steel Pipe A0999_A0999M-23 ASTM|A0999_A0999M-23|en-US Standard Specification for General Requirements for Alloy and Stainless Steel Pipe Standard new BOS Vol. 01.01 Committee A01
$ 76.00 In stock
ASTM International

Scope

1.1 This specification2 covers a group of general requirements that, unless otherwise specified in an individual specification, shall apply to the ASTM product specifications noted below.

1.2 In the case of conflict between a requirement of a product specification and a requirement of this specification, the product specification shall prevail. In the case of conflict between a requirement of the product specification or a requirement of this specification and a more stringent requirement of the purchase order, the purchase order shall prevail.

Title of Specification

ASTM Desig-
nation3

 

 

Seamless, Welded, and Heavily Cold Worked Austenitic Stainless Steel Pipes

A312/A312M

Seamless and Welded Steel Pipe for Low-Temperature
Service and Other Applications with Required Notch
Toughness

A333/A333M

Seamless Ferritic Alloy-Steel Pipe for High Temperature
Service

A335/A335M

Electric-Fusion-Welded Austenitic Chromium-Nickel Stainless
Steel Pipe for High-Temperature Service and General
Applications

A358/A358M

Carbon and Ferritic Alloy Steel Forged and Bored Pipe for
High-Temperature Service

A369/A369M

Seamless Austenitic Steel Pipe for High-Temperature
Service

A376/A376M

Welded Large Diameter Austenitic Steel Pipe for Corrosive
or High-Temperature Service

A409/A409M

Centrifugally Cast Ferritic Alloy Steel Pipe for
High-Temperature Service

A426/A426M

Centrifugally Cast Austenitic Steel Pipe for High-
Temperature Service

A451/A451M

Centrifugally Cast Iron-Chromium-Nickel High-Alloy
Tubing for Pressure Application at High
Temperatures

A608/A608M

Welded, Unannealed Austenitic Stainless Steel Tubular
Products

A778/A778M

Seamless and Welded Ferritic/Austenitic
Stainless Steel Pipe

A790/A790M

Single- or Double-Welded Austenitic Stainless Steel Pipe

A813/A813M

Cold-Worked Welded Austenitic Stainless Steel Pipe

A814/A814M

Centrifugally Cast Ferritic/Austenitic Stainless Steel Pipe
for Corrosive Environments

A872/A872M

Ferritic/Austenitic (Duplex) Stainless Steel Pipe Electric
Fusion Welded with Addition of Filler Metal

A928/A928M

Spray-Formed Seamless Austenitic Stainless Steel Pipes

A943/A943M

Spray-Formed Seamless Ferritic/Austenitic Stainless Steel Pipe

A949/A949M

Austenitic Chromium-Nickel-Silicon Alloy Steel Seamless
and Welded Pipe

A954

1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. The inch-pound units apply unless the “M” designation (SI) of the product specification is specified in the order.

Note 1: The dimensionless designator NPS (nominal pipe size) is used in this standard for such traditional terms as “nominal diameter,” “size,” “nominal bore,” and “nominal size.”

1.4 The following precautionary statement pertains only to the test method portion, Section 21, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Price:
Contact Sales
Related
Reprints and Permissions
Reprints and copyright permissions can be requested through the
Copyright Clearance Center
Details
Book of Standards Volume: 01.01
Developed by Subcommittee: A01.10
Pages: 12
DOI: 10.1520/A0999_A0999M-23
ICS Code: 23.040.10