Standard Historical Last Updated: Aug 16, 2017 Track Document
ASTM A888-03

Standard Specification for Hubless Cast Iron Soil Pipe and Fittings for Sanitary and Storm Drain, Waste, and Vent Piping Applications

Standard Specification for Hubless Cast Iron Soil Pipe and Fittings for Sanitary and Storm Drain, Waste, and Vent Piping Applications A0888-03 ASTM|A0888-03|en-US Standard Specification for Hubless Cast Iron Soil Pipe and Fittings for Sanitary and Storm Drain, Waste, and Vent Piping Applications Standard new BOS Vol. 01.02 Committee A04
$ 129.00 In stock

Scope

1.1 This specification covers cast iron soil pipe and fittings for use in gravity flow applications. It establishes standards covering material, principal dimensions, and dimensional tolerances for hubless cast iron soil pipe and fittings. These pipe and fittings are not intended for pressure applications, as the selection of the proper size for sanitary drain, waste, vent, and storm drain systems allows free air space for gravity drainage.

1.2 This specification covers pipe and fittings of the following patterns and applies to any other patterns that conform with the requirements given herein.

1.2.1 Lengths:
Figures
EDP Identification Numbers for Hubless Pipe1
10 ft (3.0 m) in sizes 1 ½ , 2, 3, 4, 5, 6, 8, 10, 12, and 15 inch.1, 2
Method of Specifying Fittings3

1.2.2Fittings:

Quarter Bend4
Quarter Bend, Reducing5
Quarter Bend, With Side Opening6
Quarter Bend, With Heel Opening7
Quarter Bend, Tapped8
Quarter Bend, Double9
Quarter Bend, Long10
Short Sweep11
Long Sweep12
Long Sweep, Reducing13
Fifth Bend14
Sixth Bend15
Eighth Bend16
Eighth Bend Long17
Sixteenth Bend18
Sanitary Tee19
Sanitary Tee With Side Opening20
Sanitary Tee With 2 in. Side Opening R or L/R and L21
Sanitary Tee, New Orleans Special With Side Opening22
Sanitary Tee With 45 Side Openings and New Orleans23
Sanitary Special Tee Tapped24
Sanitary Tapped Tee, Horizontal Twin25
Sanitary Tapped Tee, Double Vertical26
Y Branch27
Y Branch, Double28
Y Branch, Upright29
Upright Y Wide Center Florida Special30
Y Branch, Combination 1/8 Bend 31
Y Branch, Combination 1/8 Bend Double32
Sanitary Cross33
Sanitary Cross With Side Opening34
Sanitary Cross, New Orleans, With Side Openings35
Sanitary Cross, New Orleans, With 45 Special andRegular Side Openings 36
Sanitary Cross, Tapped37
Test Tee38
Tapped, Extension Piece39
Increaser-Reducer40
Increaser-Reducer, Short41
Tapped Adapter42
Blind Plug43
Iron Body Cleanout-Tapped44
P Trap 45
P Trap, Long46
P Trap, Long-Tapped47
P Trap, Deep Seal48
P Trap, Reducing49
P Trap, With Primer50
P Trap, With Tapped Inlet51
Hub Adapter52
Tapped Inlet, Double53
Modified Combination Wye and 1/8 Bend, Double54
Modified Combination Wye and 1/8 Bend, Double, Extended55
Regular or Extended Left or Right Regular or ExtendedDouble56
Regular or Extended Left or Right Regular or ExtendedDouble57
Two-Way Cleanout58
Twin Cleanout59
Closet Bend, Regular and Reducing60
Closet Flange61
Tapping Bosses62

1.3 The values stated in inch-pound units shall be regarded as the standard. The values given in parentheses shall be for information only.

Note 1—The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.

Price:
Contact Sales
Related
Reprints and Permissions
Reprints and copyright permissions can be requested through the
Copyright Clearance Center
Details
Book of Standards Volume: 01.02
Developed by Subcommittee: A04.12
Pages: 50
DOI: 10.1520/A0888-03
ICS Code: 23.040.01; 91.140.80