Standard Active Last Updated: May 03, 2023 Track Document
ASTM A861-04(2023)

Standard Specification for High-Silicon Iron Pipe and Fittings

Standard Specification for High-Silicon Iron Pipe and Fittings A0861-04R23 ASTM|A0861-04R23|en-US Standard Specification for High-Silicon Iron Pipe and Fittings Standard new BOS Vol. 01.02 Committee A04
$ 99.00 In stock
ASTM International

Abstract

This specification covers high-silicon iron pipe and pipe fittings intended for corrosion-resistant service for both above- and below-grade construction. The castings shall be true to pattern, reasonable smooth, and free from defects that would make the castings unfit for the use for which they are intended. The material shall conform to the chemical composition requirements specified. All centrifugally cast high-silicon iron pipe shall be supplied in the as-cast condition. All other pipe and fittings shall be supplied in the stress-relieved condition; the stress relieving procedures are presented. Acid-proof joints for hub/plain-end pipe shall require the use of an acid-proof rope packing. No-hub pipe and fittings shall require a special acid resistant mechanical joint coupling. High-silicon iron pipe can be cut with either manual or hydraulic snap cutters. Hydrostatic testing shall be conducted on all castings.

Scope

1.1 This specification covers high-silicon iron pipe and pipe fittings intended for corrosion-resistant service for both above- and below-grade construction.

1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

1.3 Pipe and pipe fittings shall be the no-hub (MJ) or the hub and plain-end design.

1.4 Pipe and pipe fittings shall be of the sizes specified in Table 1 and Table 2 and Figs. 1–71 or other sizes that shall be permitted to conform to the requirements given herein.

Note 1: 1 in. = 25.4 mm.

Note 1: 1 in. = 25.4 mm.

Note 1: 1 in. = 25.4 mm.

Note 1: 1 in. = 25.4 mm.

Note 1: 1 in. = 25.4 mm.

Note 1: 1 in. = 25.4 mm.

Note 1: 1 in. = 25.4 mm.

Note 1: 1 in. = 25.4 mm.

Note 1: 1 in. = 25.4 mm.

Note 1: 1 in. = 25.4 mm.

Note 1: 1 in. = 25.4 mm.

Note 1: 1 in. = 25.4 mm.

Note 1: 1 in. = 25.4 mm.

Note 1: 1 in. = 25.4 mm.

Note 1: 1 in. = 25.4 mm.

Note 1: 1 in. = 25.4 mm.


Note 1: 1 in. = 25.4 mm.

Note 1: 1 in. = 25.4 mm.

Note 1: 1 in. = 25.4 mm.

Note 1: 1 in. = 25.4 mm.

Note 1: 1 in. = 25.4 mm.

Note 1: 1 in. = 25.4 mm.

Note 1: 1 in. = 25.4 mm.

Note 1: 1 in. = 25.4 mm.

Note 1: 1 in. = 25.4 mm.

Note 1: 1 in. = 25.4 mm.


Note 1: 1 in. = 25.4 mm.

Note 1: 1 in. = 25.4 mm.

Note 1: Flange dimensions are 150 lb ANSI standard.

Note 2: 1 in. = 25.4 mm.

Note 1: 1 in. = 25.4 mm.

Size, in.

t, in.

Weight, lb

Working
Length, ft

Overall Length

 2

5/16 

0.31

7

  7 ft 25/8 in.

 3

5/16 

0.31

7

  7 ft 25/8 in.

 4

5/16 

0.31

7

  7 ft 25/8 in.

 6

13/32 

0.40

7

  7 ft 3 in.

 8

13/32 

0.40

7

  7 ft 3 in.

10

5/8 

0.62

7

  7 ft 37/8 in.

12

5/8 

0.62

5

  5 ft 4 in.

15

7/8 

0.75

5

  5 ft 41/8 in.

Note 1: 1 in. = 25.4 mm.

Note 1: 1 in. = 25.4 mm.

Note 1: 1 in. = 25.4 mm.

Note 1: 1 in. = 25.4 mm.

Note 1: 1 in. = 25.4 mm.

Note 1: 1 in. = 25.4 mm.

Note 1: 1 in. = 25.4 mm.

Note 1: 1 in. = 25.4 mm.

Note 1: 1 in. = 25.4 mm.

Note 1: 1 in. = 25.4 mm.

Note 1: 1 in. = 25.4 mm.

Note 1: 1 in. = 25.4 mm.

Note 1: 1 in. = 25.4 mm.

Note 1: 1 in. = 25.4 mm.

Note 1: 1 in. = 25.4 mm.

Note 1: 1 in. = 25.4 mm.

Note 1: 1 in. = 25.4 mm.

Note 1: 1 in. = 25.4 mm.

Note 1: 1 in. = 25.4 mm.

Note 1: 1 in. = 25.4 mm.

Note 1: 1 in. = 25.4 mm.

Note 1: 1 in. = 25.4 mm.

Note 1: 1 in. = 25.4 mm.

Note 1: 1 in. = 25.4 mm.

Note 1: Depth of seal on all traps shall be 21/2 in.

Note 2: 1 in. = 25.4 mm.

Note 1: Depth of seal on all traps shall be 21/2 in.

Note 2: 1 in. = 25.4 mm.

Note 1: Single hub vent is located on the inlet side. Depth of seal on 8 and 10 in. traps is 3 in. All others 21/2 in.

Note 2: 1 in. = 25.4 mm.

Note 1: 1 in. = 25.4 mm.

Note 1: 1 in. = 25.4 mm.

Plate
No.

Size,
in.

A,
in.

B,
in.

C,
in.

D,
in.

E,
in.

F,
in.

1
2

3
4

8
8

9
9

57/8 
63/8 

11/2 
11/2 

14
14

141/2 
141/2 

Note 1: 1 in. = 25.4 mm.


Note 1: 1 in. = 25.4 mm.

Note 1: Furnished with flat loose strainer plates.

Note 2: 1 in. = 25.4 mm.

Note 1: Traps can be supplied without cleanouts, as shown in the figure.

Note 2: 1 in. = 25.4 mm.

1.4.1 Pipe: 

1.4.1.1 No-Hub (MJ) (Fig. 1): 

 

Size (in.)

Length (ft)

 

11/2 

7

 

2

7

 

3

7

 

4

7

1.4.1.2 Hub/Plain End (Fig. 35): 

 

Size (in.)

Length (ft)

 

 2

7

 

 3

7

 

 4

7

 

 6

7

 

 8

7

 

10

5

 

12

5

 

15

5

1.4.2 Fitting (No-Hub) (MJ):

 

Figs.

Quarter Bends

2

Sixth Bends

3

Return Bends

4

Double-Branch Quarter Bend

5

Eighth Bends

6

Sixteenth Bends

7

Long-Sweep Quarter Bends

8

Sanitary Y Branches

9

Double-Branch Sanitary Y

10

Sanitary Combination Y and 1/8 Bend

11

Double-Branch Sanitary Combination Y and 1/8 Bend

12

Sanitary T Branches

13

Double Branch Sanitary T

14

Sanitary Running Traps

15

Sanitary P Traps

16

Swivel Trap P-Style, Short

17

Swivel Trap P-Style, Long

18

Swivel Trap S-Style, Long

19

Centrifugal Drum Trap P Swivel Type

20

Centrifugal Drum Trap S Swivel Type

21

Combination Cleanout and Test Tees

22

Coupling

23

Pipe Plugs

24

Cleanout Plugs

25

No-Hub (MJ) Adapter

26

Reducers-Increasers

27

Sink Outlet

28

Sink Overflows

29

Threaded Adapters

30

Trap Cleanout Details

31

No-Hub (MJ) Adapter

32

(MJ) (No-Hub) to Lead Adapter

33

Floor Drains

34

1.4.3 Fitting (Hub/Plain End): 

 

Figs.

Hub Plain-End Pipe

35

Straight Tees

36

Sanitary T Branches

37

Sanitary Y Branches

38

Double-Branch Sanitary Tee

39

Double-Branch Sanitary Y

40

Double-Branch Sanitary Combination Y and 1/8 Bend (T-Y)

41

Short-Sweep Quarter Bends

42

Long-Sweep Quarter Bends

43

Sanitary Combination Y and 1/8 Bend (T-Y)

44

Quarter Bends

45

Sixth Bends

46

Eighth Bends

47

Sixteenth Bends

48

Sanitary Increasers

49

Hub Strainers

50

Sanitary Reducers

51

Double Hubs

52

Pipe Plugs

53

Cleanout Plugs

54

Adapter – Plain end to Split Flange

55

Adapter – Hub to Split Flange

56

Combination Cleanout and Test Tees

57

Insertable Joints

58

Backwater Valves

59

Sanitary P Traps

60

Sanitary S Traps

61

Sanitary Running Traps

62

Floor Drains

63, 64, 65

Floor Drains

66

Floor Drains/Installation – Funnel Attachment

67, 68

Overflow

69

Sink Outlet

70

Detailed Cross Section of Cleanout

71

Chemical Composition

Table 3

Transverse Bend Test Minimum Requirements

Table S1.1

1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Price:
Contact Sales
Related
Reprints and Permissions
Reprints and copyright permissions can be requested through the
Copyright Clearance Center
Details
Book of Standards Volume: 01.02
Developed by Subcommittee: A04.12
Pages: 26
DOI: 10.1520/A0861-04R23
ICS Code: 23.040.10; 23.040.40