Standard Active Last Updated: Sep 05, 2024 Track Document
ASTM A484/A484M-24b

Standard Specification for General Requirements for Stainless Steel Bars, Billets, Shapes, and Forgings

Standard Specification for General Requirements for Stainless Steel Bars, Billets, Shapes, and Forgings A0484_A0484M-24B ASTM|A0484_A0484M-24B|en-US Standard Specification for General Requirements for Stainless Steel Bars, Billets, Shapes, and Forgings Standard new BOS Vol. 01.03 Committee A01
$ 99.00 In stock
ASTM International

Abstract

This specification covers general requirements that shall apply to wrought stainless steel bars, shapes, forgings, and billets or other semi-finished materials, except wire, for forging. The materials shall be furnished in one of the following conditions: (1) hot-worked; (2) hot-worked and annealed; (3) hot-worked, annealed and cold-worked; or (4) hot-worked, annealed, and heat-treated. Product analysis tolerances shall be performed wherein the specimens shall conform to the required chemical compositions of carbon, manganese, phosphorus, sulfur, silicon, chromium, nickel, molybdenum, titanium, cobalt, columbium, tantalum, copper, aluminum, nitrogen, tungsten, vanadium, and selenium. The materials shall be heat treated and austenitic stainless steels and austenitic-ferritic grades shall be furnished in the solution annealed condition and shall conform to the required values of temperature, permitted annealing procedure, quenching, and rapid cooling.

Scope

1.1 This specification2 covers general requirements that shall apply to wrought stainless steel bars, shapes, forgings, and billets or other semi-finished material (except wire) for forging, under each of the following specifications issued by ASTM: Specifications A276/A276M, A314, A458, A477, A479/A479M, A564/A564M, A565/A565M, A582/A582M, A638/A638M, A705/A705M, and A831/A831M.

1.2 In the case of conflict between a requirement of a product specification and a requirement of this specification, the product specification shall prevail. In the case of conflict between a requirement of the product specification or a requirement of this specification and a more stringent requirement of the purchase order, the purchase order shall prevail. The purchase order requirements shall not take precedence if they, in any way, violate the requirements of the product specification or this specification; for example, by waiving a test requirement or by making a test requirement less stringent.

1.3 The requirements for introduction of new materials in specifications referencing this specification are given in Annex A1.

1.4 General requirements for flat-rolled stainless steel products other than bar are covered in Specification A480/A480M.

1.5 General requirements for wire products in coils are covered in Specification A555/A555M.

1.6 This specification is expressed in both inch-pound units and in SI units; however, unless the purchase order or contract specifies the applicable M specification designation (SI units), the inch-pound units shall apply. The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.

1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Price:
Contact Sales
Related
Reprints and Permissions
Reprints and copyright permissions can be requested through the
Copyright Clearance Center
Details
Book of Standards Volume: 01.03
Developed by Subcommittee: A01.17
Pages: 22
DOI: 10.1520/A0484_A0484M-24B
ICS Code: 77.140.20