Standard Historical Last Updated: Dec 31, 2010 Track Document
ASTM A213/A213M-08a

Standard Specification for Seamless Ferritic and Austenitic Alloy-Steel Boiler, Superheater, and Heat-Exchanger Tubes

Standard Specification for Seamless Ferritic and Austenitic Alloy-Steel Boiler, Superheater, and Heat-Exchanger Tubes A0213_A0213M-08A ASTM|A0213_A0213M-08A|en-US Standard Specification for Seamless Ferritic and Austenitic Alloy-Steel Boiler, Superheater, and Heat-Exchanger Tubes Standard new BOS Vol. 01.01 Committee A01
$ 91.00 In stock

Abstract

This specification covers seamless ferritic and austenitic steel boiler, superheater, and heat-exchanger tubes. Grades containing the letter H in their designation have requirements different from those of similar grades not containing the letter H. These different requirements provide higher creep-rupture strength than normally achievable in similar grades without these different requirements. The tubes shall be made by the seamless process and shall be either hot finished or cold finished, as specified. Grade TP347HFG shall be cold finished. Heat treatment shall be done separately and in addition to heating for hot forming. The ferritic alloy and ferritic stainless steels shall be reheated. On the other hand, austenitic stainless steel tubes shall be furnished in the heat-treated condition. Alternatively, immediately after hot forming, while the temperature of the tubes is not less than the minimum solution temperature, tubes may be individually quenched in water or rapidly cooled by other means. Tension test, hardness test, flattening test, and flaring test shall be done to each tube. Also, each tube shall be subjected to the nondestructive electric test or hydrostatic test.

Scope

1.1 This specification covers seamless ferritic and austenitic steel boiler, superheater, and heat-exchanger tubes, designated Grades T5, TP304, etc. These steels are listed in Tables 1 and 2.

1.2 Grades containing the letter, H, in their designation, have requirements different from those of similar grades not containing the letter, H. These different requirements provide higher creep-rupture strength than normally achievable in similar grades without these different requirements.

1.3 The tubing sizes and thicknesses usually furnished to this specification are 1/8 in. [3.2 mm] in inside diameter to 5 in. [127 mm] in outside diameter and 0.015 to 0.500 in. [0.4 to 12.7 mm], inclusive, in minimum wall thickness or, if specified in the order, average wall thickness. Tubing having other diameters may be furnished, provided such tubes comply with all other requirements of this specification.

1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. The inch-pound units shall apply unless the M designation of this specification is specified in the order.

TABLE 1 Chemical Composition Limits, %A, for Low Alloy Steel

GradeUNS DesignationComposition, %
Carbon Manga-
nese
Phospho-
rus
Sul-
fur
Silicon
NickelChromiumMolybdenumVana-
dium
BoronNiobiumNitrogenAluminumTungstenOther Elements
T2K115470.100.20 0.300.610.025 0.025B 0.100.30...0.500.810.440.65 .....................
T5K41545 0.150.300.600.025 0.0250.50 ...4.006.000.450.65.....................
T5bK51545 0.150.300.600.025 0.0251.002.00...4.006.000.450.65.....................
T5cK41245 0.120.300.600.025 0.0250.50 ...4.006.000.450.65..................Ti 4xC0.70
T9K90941 0.150.300.600.025 0.0250.251.00...8.0010.000.901.10.....................
T11K11597 0.050.15 0.300.600.025 0.0250.501.00... 1.001.500.440.65.....................
T12K115620.050.150.300.61 0.025 0.025B0.50 ... 0.801.250.440.65 .....................
T17K12047 0.150.25 0.300.610.025 0.0250.150.35... 0.801.25...0.15..................
T21K31545 0.050.15 0.300.600.025 0.0250.501.00... 2.653.350.801.06.....................
T22K21590 0.050.15 0.300.600.025 0.025 0.50... 1.902.600.871.13.....................
T23K407120.040.100.100.600.0300.0100.50 ... 1.902.600.050.300.200.300.0005
0.006
0.020.080.030.0301.451.75...
T24K307360.050.100.300.700.0200.0100.150.45...2.202.600.901.100.200.300.0015
0.007
...0.0120.02...Ti 0.060.10
T36K210010.100.170.801.200.0300.0250.250.501.001.300.300.250.500.02...0.0150.0450.020.050...Cu 0.500.80
T91 K909010.070.140.300.60 0.020 0.010 0.200.50 0.40 8.09.50.851.050.180.25 ...0.060.100.030
0.070
0.02...Ti 0.01
Zr 0.01
T92 K92460 0.070.13 0.300.60 0.020 0.010 0.500.40 8.59.5 0.300.600.150.25 0.001
0.006
0.040.090.030
0.070
0.021.52.00Ti 0.01
Zr 0.01
T122K912710.070.140.700.0200.0100.50 0.5010.011.50.250.600.150.300.0005
0.005
0.040.100.040
0.100
0.021.502.50Cu 0.301.70
Ti 0.01
Zr 0.01
T911K910610.090.130.300.600.0200.0100.100.500.408.59.50.901.100.180.250.0003
0.006
0.060.100.040
0.090
0.020.901.10Ti 0.01
Zr 0.01

A Maximum, unless range or minimum is indicated. Where ellipses (...) appear in this table, there is no requirement, and analysis for the element need not be determined or reported.

B It is permissible to order T2 and T12 with a sulfur content of 0.045 max. See 15.3.

Price:
Contact Sales
Related
Reprints and Permissions
Reprints and copyright permissions can be requested through the
Copyright Clearance Center
Details
Book of Standards Volume: 01.01
Developed by Subcommittee: A01.10
Pages: 12
DOI: 10.1520/A0213_A0213M-08A
ICS Code: 23.040.10