Standard Historical Last Updated: Aug 16, 2017 Track Document
ASTM A74-04a

Standard Specification for Cast Iron Soil Pipe and Fittings

Standard Specification for Cast Iron Soil Pipe and Fittings A0074-04A ASTM|A0074-04A|en-US Standard Specification for Cast Iron Soil Pipe and Fittings Standard new BOS Vol. 01.02 Committee A04
$ 129.00 In stock

Scope

1.1 This specification covers cast iron soil pipe and fittings for use in gravity flow plumbing, drain, waste and vent sanitary and storm water applications. It establishes standards covering material, manufacture, mechanical and chemical properties, coating, test methods, inspection, certification, product markings, dimensions, and dimensional tolerances for extra heavy and service cast iron soil pipe and fittings. These pipe and fittings are not intended for pressure applications as the selection of the proper size for sanitary drain, waste, vent, and storm drain systems allows free air space for gravity drainage.

1.2 This specification covers pipe and fittings of the following patterns and, when so designated, shall apply to any other patterns that conform with the applicable requirements given herein.

1.2.1 Pipe

Tables
Extra heavy, 2½ ft (0.75 m), 3½ ft (1.0 m), 5 ft (1.5 m), 10 ft (3.0 m) lengths 1, 2
Service, 2½ ft (0.75 m), 3½ ft (1.0 m), 5 ft (1.5 m), 10 ft (3.0 m) 1, 2
Outside dimensions (for detailing)X1.1

1.2.2 Fittings

Tables
1/4 bends; long 1/4 bends 3, 4
1/4 bends, long low-hub 5
1/4 bends, low heel; high heel6, 7
1/4 bends, short sweep; long sweep8
1/4 bends, reducing long sweep9
1/5 bends10
1/6 bends10
1/8 bends; long 1/8 bends11
1/16 bends 11
Y branches12, 13
Y branches, cleanout on main 14
Y branches, cleanout on branch15
Y branches, inverted16
Y branches, combination 1/8 bends, single17
Y branches, combination 1/8 bends, double17
Y branches, combination 1/8 bends, cleanout18
Y branches, upright 19
Sanitary T branches, single 20
Sanitary T branches, double20
Sanitary T branches, cleanout21
Tapped sanitary T branches, single22
Tapped sanitary T branches, double22
T branches, single and double23
Tapped T branches, single 24
Tapped T branches, double 24
Horizontal twin tapped T25
T branches, cleanout 26
Vent branches, single 27
Offsets, 1/8 bend 28
Double hubs 29
Long double hubs29
Reducers 30
Increasers 31, 32
S traps 33
P traps 34, 35
Deep seal P traps 36
Running traps 37
Screw plugs (brass) 38
Blind plugs 39
Iron-body ferrules 40
Side inlets Fig. 3
Closet bends 41
Tapping bosses 42
Hubbed Cleanout Cap43

1.3 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only. Metric conversions in Table 1 and Table 2 are to two decimal places; all other metric conversions are rounded to the nearest whole number.

Price:
Contact Sales
Related
Reprints and Permissions
Reprints and copyright permissions can be requested through the
Copyright Clearance Center
Details
Book of Standards Volume: 01.02
Developed by Subcommittee: A04.12
Pages: 46
DOI: 10.1520/A0074-04A
ICS Code: 23.040.40