Standard Historical Last Updated: Sep 10, 2024 Track Document
ASTM A6/A6M-24a

Standard Specification for General Requirements for Rolled Structural Steel Bars, Plates, Shapes, and Sheet Piling

Standard Specification for General Requirements for Rolled Structural Steel Bars, Plates, Shapes, and Sheet Piling A0006_A0006M-24A ASTM|A0006_A0006M-24A|en-US Standard Specification for General Requirements for Rolled Structural Steel Bars, Plates, Shapes, and Sheet Piling Standard new BOS Vol. 01.04 Committee A01
$ 115.00 In stock
ASTM International

Abstract

This specification deals with the general requirements that apply to rolled structural steel bars, plates, shapes, and sheet piling. The steel shall be made in an open-hearth, basic-oxygen, or electric-arc furnace followed by additional refining in a ladle metallurgy furnace, or secondary melting by vacuum-arc remelting or electrostag remelting. The steel products shall undergo heat treatment, structural conditioning, and strand casting in stationary molds. Tension testing and chemical analysis shall be performed wherein the specimens shall conform to the required mechanical properties such as tensile strength, yield strength and elongation, and the required metallurgical structure and composition specifications of the products. Final products shall be legibly marked, bundled, and tagged with the applicable designation, grade, heat number, size and thickness, and name, brand, or trademark of the manufacturer for identification and shipment.

Scope

1.1 This general requirements specification2 covers a group of common requirements that, unless otherwise specified in the applicable product specification, apply to rolled structural steel bars, plates, shapes, and sheet piling covered by each of the following product specifications issued by ASTM:

ASTM
Designation3

Title of Specification

A36/A36M

Carbon Structural Steel

A131/A131M

Structural Steel for Ships

A242/A242M

High-Strength Low-Alloy Structural Steel

A283/A283M

Low and Intermediate Tensile Strength Carbon Steel Plates

A328/A328M

Steel Sheet Piling

A514/A514M

High-Yield-Strength, Quenched and Tempered Alloy Steel Plate, Suitable for Welding

A529/A529M

High-Strength Carbon-Manganese Steel of Structural Quality

A572/A572M

High-Strength Low-Alloy Columbium-Vanadium Structural Steel

A573/A573M

Structural Carbon Steel Plates

A588/A588M

High-Strength Low-Alloy Structural Steel, up to 50 ksi [345 MPa] Minimum Yield Point, with Atmospheric Corrosion Resistance

A633/A633M

Normalized High-Strength Low-Alloy Structural Steel Plates

A656/A656M

Hot-Rolled Structural Steel, High-Strength Low-Alloy Plate with Improved Formability

A690/A690M

High-Strength Low-Alloy Nickel, Copper, Phosphorus Steel H-Piles and Sheet Piling with Atmospheric Corrosion Resistance for Use in Marine Environments

A709/A709M

Structural Steel for Bridges

A710/A710M

Precipitation–Strengthened Low-Carbon Nickel-Copper-Chromium-Molybdenum-Columbium (Niobium) Alloy Structural Steel Plates

A769/A769M

Carbon and High-Strength Electric Resistance Forge-Welded Steel Structural Shapes

A786/A786M

Hot-Rolled Carbon, Low-Alloy, High-Strength Low-Alloy, and Alloy Steel Floor Plates

A827/A827M

Plates, Carbon Steel, for Forging and Similar Applications

A829/A829M

Alloy Structural Steel Plates

A830/A830M

Plates, Carbon Steel, Structural Quality, Furnished to Chemical Composition Requirements

A857/A857M

Steel Sheet Piling, Cold Formed, Light Gage

A871/A871M

High-Strength Low-Alloy Structural Steel Plate With Atmospheric Corrosion Resistance

A913/A913M

High-Strength Low-Alloy Steel Shapes of Structural Quality, Produced by Quenching and Self-Tempering Process (QST)

A945/A945M

High-Strength Low-Alloy Structural Steel Plate with Low Carbon and Restricted Sulfur for Improved Weldability, Formability, and Toughness

A950/A950M

Fusion-Bonded Epoxy-Coated Structural Steel H-Piles and Sheet Piling

A992/A992M

Structural Steel Shapes

A1043/A1043M

Structural Steel with Low Yield to Tensile Ratio for Use in Buildings

A1066/A1066M

High-Strength Low-Alloy Structural Steel Plate Produced by Thermo-Mechanical Controlled Process (TMCP)

A1077/A1077M

Structural Steel with Improved Yield Strength at High Temperature for Use in Buildings

1.2 Annex A1 lists permitted variations in dimensions and mass (Note 1) in SI units. The values listed are not exact conversions of the values in Tables 1 to 31 inclusive but are, instead, rounded or rationalized values. Conformance to Annex A1 is mandatory when the “M” specification designation is used.

Note 1: The term “weight” is used when inch-pound units are the standard; however, under SI, the preferred term is “mass.”

1.3 Annex A2 lists the dimensions of some shape profiles.

1.4 Appendix X1 provides information on coil as a source of structural products.

1.5 Appendix X2 provides information on the variability of tensile properties in plates and structural shapes.

1.6 Appendix X3 provides information on weldability.

1.7 Appendix X4 provides information on cold bending of plates, including suggested minimum inside radii for cold bending.

1.8 This general requirements specification also covers a group of supplementary requirements that are applicable to several of the above product specifications as indicated therein. Such requirements are provided for use where additional testing or additional restrictions are required by the purchaser, and apply only where specified individually in the purchase order.

1.9 In case of any conflict in requirements, the requirements of the applicable product specification prevail over those of this general requirements specification.

1.10 Additional requirements that are specified in the purchase order and accepted by the supplier are permitted, provided that such requirements do not negate any of the requirements of this general requirements specification or the applicable product specification.

1.11 For purposes of determining conformance with this general requirements specification and the applicable product specification, values are to be rounded to the nearest unit in the right-hand place of figures used in expressing the limiting values in accordance with the rounding method of Practice E29.

1.12 The text of this general requirements specification contains notes or footnotes, or both, that provide explanatory material. Such notes and footnotes, excluding those in tables and figures, do not contain any mandatory requirements.

1.13 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with this specification.

1.14 This general requirements specification and the applicable product specification are expressed in both inch-pound units and SI units; however, unless the order specifies the applicable “M” specification designation (SI units), the structural product is furnished to inch-pound units.

1.15 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.16 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Price:
Contact Sales
Related
Reprints and Permissions
Reprints and copyright permissions can be requested through the
Copyright Clearance Center
Details
Book of Standards Volume: 01.04
Developed by Subcommittee: A01.02
Pages: 64
DOI: 10.1520/A0006_A0006M-24A
ICS Code: 77.140.60