If you are an ASTM Compass Subscriber and this document is part of your subscription, you can access it for free at ASTM Compass
    ASTM F3478 - 20

    Standard Practice for Development of a Durability and Reliability Flight Demonstration Program for Low-Risk Unmanned Aircraft Systems (UAS) under FAA Oversight

    Active Standard ASTM F3478 | Developed by Subcommittee: F38.01

    Book of Standards Volume: 15.09


      Format Pages Price  
    PDF 22 $78.00   ADD TO CART
    Hardcopy (shipping and handling) 22 $78.00   ADD TO CART



    Significance and Use

    4.1 Demonstration plans developed in accordance with this practice will include all necessary content and key considerations to support an effective flight demonstration program aimed at approval or certification of UAS by the FAA through D&R demonstration.

    4.2 This practice does not address planning requirements for UAS development testing. It is assumed that a manufacturer has completed all UAS design and development and is preparing demonstration programs to support compliance demonstration on a stable and controlled system configuration. Manufacturers who wish to prepare a detailed design and development program should review Specification F3298 for programmatic examples.

    4.3 This practice is intended to be used on low-risk UAS that meet the following design criteria and operating limitations.

    4.3.1 The UAS has a command and control link that enables the pilot-in-command to take contingency action.

    4.3.2 The unmanned aircraft (UA) has a kinetic energy of 25 000 ft-lb calculated in accordance with methods specified within the MOC.

    4.3.3 The UA is operated 400 ft above ground level (AGL).

    4.3.4 No operations over open-air assemblies (operations over people are acceptable).

    4.3.5 No flight into known icing.

    4.3.6 Maximum of 20:1 aircraft to pilot ratio.

    4.3.7 The UA is electrically powered (excludes internal combustion engines and fuel cells).

    1. Scope

    1.1 This standard practice is intended for low-risk UAS seeking type certification by the Federal Aviation Administration (FAA) under 14 CFR Part 21.17(b) in accordance with the FAA durability and reliability (D&R) means of compliance (MOC). The definition of “low-risk UAS” does not necessarily align with other definitions found within corresponding ASTM standards (F3442/F3442M) or other UAS-related standards. For the purposes of this practice, “low-risk” is defined as a UAS operated in accordance with the concept of operations (CONOPs), eligibility criteria, and kinetic energy threshold specified in the G-1 Issue Paper (which will be provided to the applicant by the FAA). See 4.3 for design criteria and operating limitations for low-risk UAS.

    1.2 This standard practice establishes a common methodology and key considerations for the development of minimum flight plans for low-risk UAS that demonstrate aircraft reliability as part of a D&R MOC.

    1.3 The scope of this standard practice encompasses D&R planning, data collection, and reporting.

    1.4 The values stated in SI units are to be regarded as standard. This is not intended to limit the systems of units used for design, development testing, or demonstration testing. However, the units of measurement used on pilot-facing placards and markings and manuals must be the same as those used on the corresponding equipment with recognition that international aviation utilizes feet for altitude and knots for airspeed as operational parameters.

    1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

    1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.


    2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    ASTM Standards

    F2908 Specification for Unmanned Aircraft Flight Manual (UFM) for an Unmanned Aircraft System (UAS)

    F2909 Specification for Continued Airworthiness of Lightweight Unmanned Aircraft Systems

    F3060 Terminology for Aircraft

    F3298 Specification for Design, Construction, and Verification of Lightweight Unmanned Aircraft Systems (UAS)

    F3341/F3341M Terminology for Unmanned Aircraft Systems

    F3442/F3442M Specification for Detect and Avoid System Performance Requirements

    FAA Documents

    FAA D&R MOC

    FAA Order 8110.54A


    Referencing This Standard
    Link Here
    Link to Active (This link will always route to the current Active version of the standard.)

    DOI: 10.1520/F3478-20

    Citation Format

    ASTM F3478-20, Standard Practice for Development of a Durability and Reliability Flight Demonstration Program for Low-Risk Unmanned Aircraft Systems (UAS) under FAA Oversight, ASTM International, West Conshohocken, PA, 2020, www.astm.org

    Back to Top