| Format | Pages | Price |   |
![]() |
9 | $50.00 | ![]() |
|
![]() |
Hardcopy (shipping and handling) | 9 | $50.00 | ![]() |
![]() |
Standard + Redline PDF Bundle ![]() |
18 | $60.00 | ![]() |
Historical Version(s) - view previous versions of standard
Work Item(s) - proposed revisions of this standard
More F25.11 Standards Related Products Standard References
1. Scope
1.1 This specification establishes the performance characteristics required for Metallic Press-Connect Fittings for use in piping and tubing systems with a maximum allowable working pressure of three-hundred pounds per square inch (300 psi) [2.07 MPa]. These fittings directly attach to pipe or tube by mechanical deformation of the pipe or tube or fitting, or a combination thereof, creating a seal and a restrained joint. The seal may be created via the mechanical deformation (of the pipe, tube or fitting) or created independently. Successful completion of the tests described herein constitutes completion of the technical portion of the qualification process.
1.2 The tests specified are applicable only to ascertain the performance characteristics. These tests are not intended for use in the evaluation of non-Press-Connect Fittings.
1.3 Refer to IACS UR P2.7.4, Table-7 for Metallic Press-Connect Fittings applications.
1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.
ISO Standards
ISO 19921 ISO 19922 Ships and Marine Technology Fire Resistance of Metallic Pipe Components with Resilient and Elastomeric Seals Requirements Imposed on the Test BenchASTM Standards
A53/A53M Specification for Pipe, Steel, Black and Hot-Dipped, Zinc-Coated, Welded and Seamless
A135/A135M Specification for Electric-Resistance-Welded Steel Pipe
A262 Practices for Detecting Susceptibility to Intergranular Attack in Austenitic Stainless Steels
A269 Specification for Seamless and Welded Austenitic Stainless Steel Tubing for General Service
A276 Specification for Stainless Steel Bars and Shapes
A312/A312M Specification for Seamless, Welded, and Heavily Cold Worked Austenitic Stainless Steel Pipes
A795/A795M Specification for Black and Hot-Dipped Zinc-Coated (Galvanized) Welded and Seamless Steel Pipe for Fire Protection Use
B16/B16M Specification for Free-Cutting Brass Rod, Bar and Shapes for Use in Screw Machines
B62 Specification for Composition Bronze or Ounce Metal Castings
B75/B75M Specification for Seamless Copper Tube
B88 Specification for Seamless Copper Water Tube
B124/B124M Specification for Copper and Copper Alloy Forging Rod, Bar, and Shapes
B140/B140M Specification for Copper-Zinc-Lead (Red Brass or Hardware Bronze) Rod, Bar, and Shapes
B283 Specification for Copper and Copper-Alloy Die Forgings (Hot-Pressed)
B371/B371M Specification for Copper-Zinc-Silicon Alloy Rod
B466/B466M Specification for Seamless Copper-Nickel Pipe and Tube
B467 Specification for Welded Copper-Nickel Pipe
B584 Specification for Copper Alloy Sand Castings for General Applications
B858 Test Method for Ammonia Vapor Test for Determining Susceptibility to Stress Corrosion Cracking in Copper Alloys
B967/B967M Specification for Copper-Zinc-Tin-Bismuth Alloy Rod, Bar and Wire
D2000 Classification System for Rubber Products in Automotive Applications
ASME Standards
ASME B1.20.1 ASME B16.51 ASME B36.10 Welded and Seamless Wrought Steel Pipe ASME B46.1 Surface Texture (Surface Roughness, Waviness, and Lay)IACS Document
UR P2.11 Type Approval of Mechanical JointsICS Code
ICS Number Code 23.100.40 (Piping and couplings)
UNSPSC Code
UNSPSC Code 40170000(Pipe piping and pipe fittings)
Link Here | |||
Link to Active (This link will always route to the current Active version of the standard.) | |||
DOI: 10.1520/F3226_F3226M-19
Citation Format
ASTM F3226 / F3226M-19, Standard Specification for Metallic Press-Connect Fittings for Piping and Tubing Systems, ASTM International, West Conshohocken, PA, 2019, www.astm.org
Back to Top