| ||Format||Pages||Price|| |
|25||$72.00||  ADD TO CART|
|Hardcopy (shipping and handling)||25||$72.00||  ADD TO CART|
1.1 This specification establishes parameters for the design and manufacture of outdoor fitness equipment as defined in .
1.2 It is intended that these fitness products will be used in an unsupervised outdoor setting or environment and will be permanently anchored.
1.2.1 It is the intent of this specification to only specify requirements for outdoor fitness equipment and its installation and not the design of the facility or grounds on which the products are to be installed.
1.3 The specifications set forth in this standard are intended to minimize the likelihood of serious injuries.
1.3.1 The specifications set forth in this standard are for outdoor fitness equipment intended for use in an unsupervised setting by individuals age 13 and older.
1.4 The values stated in SI (metric) units are to be regarded as standard. The values in parentheses are for information only.
1.5 General Measures, Tolerances, and Conversions:
1.5.1 The general tolerances for this specification (unless otherwise specified) are as follows:
X mm (X in.)
± 13.0 mm (0.5 in.)
X.X mm (X.X in.)
±1.3 mm (0.05 in.)
X.XX mm (X.XX in.)
±.0.130 mm (0.005 in.)
1.5.2 These tolerances still apply to a dimension even when terms like greater than, less than, minimum, or maximum are used.
1.6 This standard is to be used in conjunction with Test Methods and Specification . If a design or installation concern is not addressed in this specification then the applicable requirements of Specification shall be used.
1.6.1 This standard takes precedence over Specification and Test Methods in areas that are addressed in this document.
1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.
D2240 Test Method for Rubber Property--Durometer Hardness
F698 Specification for Physical Information to be Provided for Amusement Rides and Devices
F846 Guide for Testing Performance of Amusement Rides and Devices
F853 Practice for Maintenance Procedures for Amusement Rides and Devices
F893 Guide for Auditing Amusement Rides and Devices
F963 Consumer Safety Specification for Toy Safety
F1004 Consumer Safety Specification for Expansion Gates and Expandable Enclosures
F1077 Guide for Selection of Committee F16 Fastener Specifications
F1159 Practice for Design of Amusement Rides and Devices that are Outside the Purview of Other F24 Design Standards
F1292 Specification for Impact Attenuation of Surfacing Materials Within the Use Zone of Playground Equipment
F1749 Specification for Fitness Equipment and Fitness Facility Safety Signage and Labels
F1918 Safety Performance Specification for Soft Contained Play Equipment
F1951 Specification for Determination of Accessibility of Surface Systems Under and Around Playground Equipment
F2276 Specification for Fitness Equipment
F2571 Test Methods for Evaluating Design and Performance Characteristics of Fitness Equipment
F3021 Specification for Universal Design of Fitness Equipment for Inclusive Use by Persons with Functional Limitations and Impairments
F3022 Test Method for Evaluating the Universal Design of Fitness Equipment for Inclusive Use by Persons with Functional Limitations and Impairments
ICS Number Code 97.220.40 (Outdoor and water sports equipment)
UNSPSC Code 49200000(Fitness equipment)
|Link to Active (This link will always route to the current Active version of the standard.)|
ASTM F3101-15, Standard Specification for Unsupervised Public Use Outdoor Fitness Equipment, ASTM International, West Conshohocken, PA, 2015, www.astm.orgBack to Top