| ||Format||Pages||Price|| |
|7||$50.00||  ADD TO CART|
|Hardcopy (shipping and handling)||7||$50.00||  ADD TO CART|
1.1 This specification covers the requirements for nonferrous socket set screws sizes 0.125 (#5) through 2.000 in., square head set screws sizes 0.190 (#10) through 1.500 in., and slotted headless set screws 0.125 (#5) through 0.750 in. in diameter manufactured from a number of nonferrous alloys in use in the marine industry and the U.S. Navy subject to seawater wetting and salt atmosphere but that also may be used in other applications. It is recommended that copper-based alloys not be used in attempting to prevent mechanical components from rotating, such as locking shafts, because of the low hardness of the alloys. Some alloys or sizes or both of set screws may not be readily available. Manufacturers or suppliers should be contacted before design development or anticipated procurement.
1.2 Units—The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard.
Note 1: A complete metric companion to Specification will be developed—F3042M; therefore, no metric equivalents are shown in this specification.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.
B154 Test Method for Mercurous Nitrate Test for Copper Alloys
E18 Test Methods for Rockwell Hardness of Metallic Materials
E29 Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
E53 Test Method for Determination of Copper in Unalloyed Copper by Gravimetry
E54 Test Methods for Chemical Analysis of Special Brasses and Bronzes
E55 Practice for Sampling Wrought Nonferrous Metals and Alloys for Determination of Chemical Composition
E62 Test Methods for Chemical Analysis of Copper and Copper Alloys (Photometric Methods)
E75 Test Methods for Chemical Analysis of Copper-Nickel and Copper-Nickel-Zinc Alloys
E76 Test Methods for Chemical Analysis of Nickel-Copper Alloys
E120 Test Methods for Chemical Analysis of Titanium and Titanium Alloys
E165 Practice for Liquid Penetrant Examination for General Industry
E350 Test Methods for Chemical Analysis of Carbon Steel, Low-Alloy Steel, Silicon Electrical Steel, Ingot Iron, and Wrought Iron
E354 Test Methods for Chemical Analysis of High-Temperature, Electrical, Magnetic, and Other Similar Iron, Nickel, and Cobalt Alloys
E384 Test Method for Microindentation Hardness of Materials
E478 Test Methods for Chemical Analysis of Copper Alloys
E1409 Test Method for Determination of Oxygen and Nitrogen in Titanium and Titanium Alloys by Inert Gas Fusion
F788/F788M Specification for Surface Discontinuities of Bolts, Screws, and Studs, Inch and Metric Series
F1470 Practice for Fastener Sampling for Specified Mechanical Properties and Performance Inspection
ICS Number Code 21.060.10 (Bolts, screws, studs)
UNSPSC Code 31161518(Socket screw)
|Link to Active (This link will always route to the current Active version of the standard.)|
ASTM F3042-13(2018), Standard Specification for Nonferrous Hex Socket, Slotted Headless, and Square Head Set Screws, ASTM International, West Conshohocken, PA, 2018, www.astm.orgBack to Top