| Format | Pages | Price |   |
![]() |
6 | $52.00 | ![]() |
|
![]() |
Hardcopy (shipping and handling) | 6 | $52.00 | ![]() |
Historical Version(s) - view previous versions of standard
More F17.26 Standards Related Products Standard References
Abstract
This specification establishes requirements and test methods for double wall, annular extruded corrugated polyethylene (PE) pipe and fittings used in mine heap leach pile aeration. It covers materials, workmanship, dimensions, perforations, pipe stiffness, elongation, joint separation resistance, quality of extruded polyethylene, brittleness, testing, and marking of corrugated PE pipe and fittings with diameters of 100 mm (4 inch), 150 mm (6 inch), 200 mm (8 inch), 250 mm (10 inch), 300 mm (12 inch), 375 mm (15 inch), and 450 mm (18 inch).
This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.
1. Scope
1.1 This specification covers requirements and test methods for materials, workmanship, dimensions, perforations, pipe stiffness, elongation, joint separation resistance, quality of extruded polyethylene, brittleness, testing, and marking of corrugated polyethylene (PE) pipe and fittings for mine heap leach pile aeration. It covers with nominal sizes 100 mm (4 in.), 150 mm (6 in.), 200 mm (8 in.), 250 mm (10 in.) 300 mm (12 in.), 375 mm (15 in.), and 450 mm (18 in.) diameter.
1.2 This specification covers double wall, annular extruded corrugated polyethylene pipe as depicted in Fig. 1.
FIG. 1 Typical Double Wall Profile Cross-Section
1.3 The values in parentheses are provided for information only.
1.4 The following precautionary caveat pertains only to the test method portion, Section 9, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.
Military Standard
MIL-STD-129 Marking for Shipment and StorageASTM Standards
D618 Practice for Conditioning Plastics for Testing
D1600 Terminology for Abbreviated Terms Relating to Plastics
D2122 Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
D2412 Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-Plate Loading
D2444 Practice for Determination of the Impact Resistance of Thermoplastic Pipe and Fittings by Means of a Tup (Falling Weight)
D3212 Specification for Joints for Drain and Sewer Plastic Pipes Using Flexible Elastomeric Seals
D3350 Specification for Polyethylene Plastics Pipe and Fittings Materials
D3895 Test Method for Oxidative-Induction Time of Polyolefins by Differential Scanning Calorimetry
F412 Terminology Relating to Plastic Piping Systems
F2136 Test Method for Notched, Constant Ligament-Stress (NCLS) Test to Determine Slow-Crack-Growth Resistance of HDPE Resins or HDPE Corrugated Pipe
Federal Standards
Federal Emergency Management Agency (FEMA) Technic Fed. Std. No. 123 Marking for Shipment (Civil Agencies)ICS Code
ICS Number Code 23.040.20 (Plastic pipes)
UNSPSC Code
UNSPSC Code 13111016(Polyethylene); 40171500(Commercial pipe and piping)
Link Here | |||
Link to Active (This link will always route to the current Active version of the standard.) | |||
DOI: 10.1520/F2987-12R18
Citation Format
ASTM F2987-12(2018), Standard Specification for Corrugated Polyethylene Pipe and Fittings for Mine Heap Leach Aeration Applications, ASTM International, West Conshohocken, PA, 2018, www.astm.org
Back to Top