| ||Format||Pages||Price|| |
|7||$48.00||  ADD TO CART|
|Hardcopy (shipping and handling)||7||$48.00||  ADD TO CART|
This specification covers welded wire mesh fence fabric produced from steel wire or metallic-coated steel wire. The metallic-coated fabric may be polymer coated after fabrication. This specification identifies the three major classifications of welded wire mesh fence fabric - Panel Sizes Model A, B, and C - and the test methods conducted on the welded wire fabric. It also indicates the physical properties, dimension, tolerance, and workmanship of the welded wire mesh fence fabric.
This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.
1.1 This specification covers welded wire mesh fence fabric produced from steel wire or metallic-coated steel wire. The metallic-coated fabric may be polymer coated after fabrication.
1.2 Welded wire mesh fence fabric is produced in four types, based on the kind of coating, as described in Section .
1.3 This specification is applicable to orders in either inch-pound units or SI units. Values stated in either inch-pound or SI units are to be regarded separately as the standard. Within the text, the SI units are shown in brackets. The values in the two systems are not exact equivalents; therefore, each system shall be used independent of the other, without combining values in any way.
1.4 This specification references notes and footnotes, which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of this specification.
1.5 The following safety hazards caveat pertains only to the test methods portion, This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. , of this specification:
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.
A82/A82M Specification for Steel Wire, Plain, for Concrete Reinforcement
A90/A90M Test Method for Weight [Mass] of Coating on Iron and Steel Articles with Zinc or Zinc-Alloy Coatings
A123/A123M Specification for Zinc (Hot-Dip Galvanized) Coatings on Iron and Steel Products
A185/A185M Specification for Steel Welded Wire Reinforcement, Plain, for Concrete
A641/A641M Specification for Zinc-Coated (Galvanized) Carbon Steel Wire
A853 Specification for Steel Wire, Carbon, for General Use
A856/A856M Specification for Zinc-5 % Aluminum-Mischmetal Alloy-Coated Carbon Steel Wire
A902 Terminology Relating to Metallic Coated Steel Products
A1064/A1064M Specification for Carbon-Steel Wire and Welded Wire Reinforcement, Plain and Deformed, for Concrete
B117 Practice for Operating Salt Spray (Fog) Apparatus
D1499 Practice for Filtered Open-Flame Carbon-Arc Exposures of Plastics
F934 Specification for Standard Colors for Polymer-Coated Chain Link Fence Materials
ICS Number Code 77.140.65 (Steel wire, wir ropes and link chains)
UNSPSC Code 31152206(Coated steel wire)
|Link to Active (This link will always route to the current Active version of the standard.)|
ASTM F2919 / F2919M-12(2018), Standard Specification for Welded Wire Mesh Fence Fabric (Metallic-Coated or Polymer Coated) with Variable Mesh Patterns or Meshes Greater than 6 in.2 [3871 mm2] in Panels, ASTM International, West Conshohocken, PA, 2018, www.astm.orgBack to Top