ASTM F2882 / F2882M - 17

    Standard Specification for Screws, Alloy Steel, Heat Treated, 170 ksi and 1170 MPa Minimum Tensile Strength (Inch and Metric)

    Active Standard ASTM F2882 / F2882M | Developed by Subcommittee: F16.02

    Book of Standards Volume: 01.08


      Format Pages Price  
    PDF 7 $46.00   ADD TO CART
    Hardcopy (shipping and handling) 7 $46.00   ADD TO CART
    Standard + Redline PDF Bundle 14 $55.20   ADD TO CART


    Abstract

    This specification covers the requirements for quenched and tempered alloy steel screws 0.060 through 1 1/2 inches in diameter having a minimum ultimate tensile strength of 170 KSI. High strength screws shall be heat treated by quenching in oil from above the transformation temperature and then tempered by reheating to at least 797°F to within the hardness range. One or more of the following alloying elements: chromium, nickel, molybdenum, or vanadium shall be present in sufficient quantity to ensure that the specified strength properties are met after oil quenching and tempering. The hardness limits shall be met anywhere on the cross section through the threads, one diameter from the screw point.

    This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.

    1. Scope

    1.1 This specification covers the requirements for quenched and tempered alloy steel screws 0.060 through 11/2 in. and 1.6 through 48 mm in diameter having a minimum ultimate tensile strength of 170 KSI or 1170 MPa.

    1.2 The values are stated in inch-pound units for inch fasteners and SI metric units for metric fasteners. The values stated in each system may not be exact equivalents; therefore each system shall be used independently of the other. Combining values from the two systems may result in non-conformance to the standard.

    1.3 The following hazard caveat pertains only to the test method portion, Section 10, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

    1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.


    2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    ASTM Standards

    A751 Test Methods, Practices, and Terminology for Chemical Analysis of Steel Products

    E112 Test Methods for Determining Average Grain Size

    F606/F606M Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets

    F788/F788M Specification for Surface Discontinuities of Bolts, Screws, and Studs, Inch and Metric Series

    F1470 Practice for Fastener Sampling for Specified Mechanical Properties and Performance Inspection

    F1940 Test Method for Process Control Verification to Prevent Hydrogen Embrittlement in Plated or Coated Fasteners

    F2282 Specification for Quality Assurance Requirements for Carbon and Alloy Steel Wire, Rods, and Bars for Mechanical Fasteners

    F2328 Test Method for Determining Decarburization and Carburization in Hardened and Tempered Threaded Steel Bolts, Screws, Studs, and Nuts

    F2328M Test Method for Determining Decarburization and Carburization in Hardened and Tempered Threaded Steel Bolts, Screws, Studs, and Nuts (Metric)


    ICS Code

    ICS Number Code 21.060.10 (Bolts, screws, studs)

    Referencing This Standard
    Link Here
    Link to Active (This link will always route to the current Active version of the standard.)

    DOI: 10.1520/F2882_F2882M-17

    Citation Format

    ASTM F2882 / F2882M-17, Standard Specification for Screws, Alloy Steel, Heat Treated, 170 ksi and 1170 MPa Minimum Tensile Strength (Inch and Metric), ASTM International, West Conshohocken, PA, 2017, www.astm.org

    Back to Top