If you are an ASTM Compass Subscriber and this document is part of your subscription, you can access it for free at ASTM Compass
ASTM F2830 - 11(2017)
Standard Specification for Manufacture and Joining of Polyethylene (PE) Gas Pressure Pipe With a Peelable Polypropylene (PP) Outer Layer
| Format | Pages | Price | ||
 |
3 | $48.00 |  ADD TO CART |
|
 |
Hardcopy (shipping and handling) | 3 | $48.00 | ADD TO CART |
Historical Version(s) - view previous versions of standard
More F17.60 Standards Related Products Standard References
Abstract
This specification covers manufacturing and joining requirements for peelable or skinned polyethylene (PE) pipe, which is PE pipe meeting the requirements of Specification D2513, with a peelable outer layer of polypropylene (PP). The peelable PP layer does not contribute to outside diameter and wall thickness used for pressure rating or tensile loading calculations.
This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.
1. Scope
1.1 This standard specification covers manufacturing and joining requirements for peelable (skinned) polyethylene (PE) pipe, which is PE pipe meeting the requirements of Specification D2513, with a peelable outer layer of polypropylene (PP). These requirements are in addition to those in Specification D2513 for the PE pipe.
1.2 The peelable PP layer does not contribute to outside diameter and wall thickness used for pressure rating or tensile loading calculations.
1.3 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in figures and tables) shall not be considered as requirements of the standard.
1.4 Units—The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.
ASTM Standards
D1600 Terminology for Abbreviated Terms Relating to Plastics
D2513 Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings
D4101 Specification for Polypropylene Injection and Extrusion Materials
F412 Terminology Relating to Plastic Piping Systems
F1055 Specification for Electrofusion Type Polyethylene Fittings for Outside Diameter Controlled Polyethylene and Crosslinked Polyethylene (PEX) Pipe and Tubing
F1563 Specification for Tools to Squeeze-off Polyethylene (PE) Gas Pipe or Tubing
ISO Standard
ISO 17454 Plastics piping systems - multilayer pipe - test method for the adhesion of the different layers using a pulling rig.EN Standard
EN 1411ICS Code
ICS Number Code 23.040.20 (Plastic pipes)
UNSPSC Code
UNSPSC Code 40171617(Industrial PVC pipe)
Referencing This Standard
| Link Here | |||
| Link to Active (This link will always route to the current Active version of the standard.) | |||
DOI: 10.1520/F2830-11R17
Citation Format
ASTM F2830-11(2017), Standard Specification for Manufacture and Joining of Polyethylene (PE) Gas Pressure Pipe With a Peelable Polypropylene (PP) Outer Layer, ASTM International, West Conshohocken, PA, 2017, www.astm.org
Back to Top