| Format | Pages | Price |   |
![]() |
4 | $46.00 | ![]() |
|
![]() |
Hardcopy (shipping and handling) | 4 | $46.00 | ![]() |
![]() |
Standard + Redline PDF Bundle ![]() |
8 | $54.00 | ![]() |
Historical Version(s) - view previous versions of standard
More F06.80 Standards Related Products Standard References
Abstract
This specification covers sheet linoleum floor covering. These floor coverings are intended for use in commercial, light commercial, and residential buildings based on serviceability characteristics. The floor coverings shall be of the following types: Type I; Type II; and Type III. The jute backing shall be firmly bonded to and partially embedded in the linoleum mix. The minimum amount of linoleum cement shall be 30 % when tested. The following test methods shall be performed: overall thickness; static load; resistance to chemicals; resistance to heat; resistance to light; flexibility; static dissipation; and wear surface.
This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.
1. Scope
1.1 This specification covers sheet linoleum floor covering.
1.2 Three types of linoleum floor covering are covered (see Section 4). These floor coverings are intended for use in commercial, light commercial, and residential buildings based on serviceability characteristics. General information and performance characteristics, which determine serviceability and recommended use, are included in this specification.
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.4 The following safety hazards caveat pertains only to the test methods portion, Section 11, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.
ASTM Standards
F137 Test Method for Flexibility of Resilient Flooring Materials with Cylindrical Mandrel Apparatus
F141 Terminology Relating to Resilient Floor Coverings
F150 Test Method for Electrical Resistance of Conductive and Static Dissipative Resilient Flooring
F386 Test Method for Thickness of Resilient Flooring Materials Having Flat Surfaces
F410 Test Method for Wear Layer Thickness of Resilient Floor Coverings by Optical Measurement
F710 Practice for Preparing Concrete Floors to Receive Resilient Flooring
F925 Test Method for Resistance to Chemicals of Resilient Flooring
F970 Test Method for Measuring Recovery Properties of Floor Coverings after Static Loading
F1482 Practice for Installation and Preparation of Panel Type Underlayments to Receive Resilient Flooring
F1514 Test Method for Measuring Heat Stability of Resilient Flooring by Color Change
F1515 Test Method for Measuring Light Stability of Resilient Flooring by Color Change
F1516 Practice for Sealing Seams of Resilient Flooring Products by the Heat Weld Method (when Recommended)
European Norms
ISO 26985American National Standard
ANSI/ASQC Z1.4 Sampling Procedures and Tables for Inspection by Attributes Available from American National Standards Institute, 11 West 42 nd St., 13th Floor, New York, NY 10036.ICS Code
ICS Number Code 91.060.30 (Ceilings. Floors. Stairs)
UNSPSC Code
UNSPSC Code 52101500(Rugs and mats); 30161700(Flooring)
Link Here | |||
Link to Active (This link will always route to the current Active version of the standard.) | |||
DOI: 10.1520/F2034-18
Citation Format
ASTM F2034-18, Standard Specification for Sheet Linoleum Floor Covering, ASTM International, West Conshohocken, PA, 2018, www.astm.org
Back to Top