ASTM F2021 - 11
Standard Guide for Design and Installation of Plastic Siphonic Roof Drainage Systems
| Format | Pages | Price | ||
 |
3 | $40.00 |  ADD TO CART |
|
 |
Hardcopy (shipping and handling) | 3 | $40.00 | ADD TO CART |
|
Standard + Redline PDF Bundle  |
6 | $48.00 | ADD TO CART |
Historical Version(s) - view previous versions of standard
Significance and Use
The information provided in this standard guide is intended for use by designers and specifiers of siphonic roof drainage systems and their related components. Specifically, this guide addresses the use and limitations of plastic pipe and fittings in siphonic roof drainage systems where internal operating pressures are typically sub-atmospheric.
1. Scope
1.1 This guide covers design and installation considerations for plastic siphonic roof drain systems for industrial, commercial, public, and residential buildings. Requirements for materials, pipe, and fittings are included.
1.2 The interchangeability of pipe and fittings made by different manufacturers is not addressed in this guide. Transition fittings for joining pipe and fittings of different manufacturers is provided for in the referenced pipe and fitting specification.
1.3 In referee decisions, the SI units shall be used for metric-sized pipe and inch-pound units for pipe sized in the IPS system (ANSI B36.10). In all cases, the values given in parentheses are for information only.
2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.
ASTM Standards
D696 Test Method for Coefficient of Linear Thermal Expansion of Plastics Between -30C and 30C with a Vitreous Silica Dilatometer
D1600 Terminology for Abbreviated Terms Relating to Plastics
D1785 Specification for Poly(Vinyl Chloride) (PVC) Plastic Pipe, Schedules 40, 80, and 120
D2661 Specification for Acrylonitrile-Butadiene-Styrene (ABS) Schedule 40 Plastic Drain, Waste, and Vent Pipe and Fittings
D2665 Specification for Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings
D2751 Specification for Acrylonitrile-Butadiene-Styrenea??(ABS)a??Sewera??Pipea??anda??Fittings
D2949 Specification for 3.25-in. Outside Diameter Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings
D3034 Specification for Type PSM Poly(Vinyl Chloride) (PVC) Sewer Pipe and Fittings
D3350 Specification for Polyethylene Plastics Pipe and Fittings Materials
E84 Test Method for Surface Burning Characteristics of Building Materials
E814 Test Method for Fire Tests of Penetration Firestop Systems
E1966 Test Method for Fire-Resistive Joint Systems
E2393 Practice for On-Site Inspection of Installed Fire Resistive Joint Systems and Perimeter Fire Barriers
F412 Terminology Relating to Plastic Piping Systems
F628 Specification for Acrylonitrile-Butadiene-Styrene (ABS) Schedule 40 Plastic Drain, Waste, and Vent Pipe With a Cellular Core
F714 Specification for Polyethylene (PE) Plastic Pipe (DR-PR) Based on Outside Diameter
F891 Specification for Coextruded Poly(Vinyl Chloride) (PVC) Plastic Pipe With a Cellular Core
F1901 Specification for Polyethylene (PE) Pipe and Fittings for Roof Drain Systems
ANSI/ASME Standards
B36.10 Standard Dimensions of Steel Pipe (IPS)ANSI/UL Standard
UL-1479 (see Test Method )Other References
NFPA 5000 Building CodeICS Code
ICS Number Code 91.060.20 (Roofs)
UNSPSC Code
UNSPSC Code 13102001(Acrylonitrile butadiene styrene ABS); 30151605(Roofing drains)
Referencing This Standard
| Link Here | |||
| Link to Active (This link will always route to the current Active version of the standard.) | |||
DOI: 10.1520/F2021-11
Citation Format
ASTM F2021-11, Standard Guide for Design and Installation of Plastic Siphonic Roof Drainage Systems, ASTM International, West Conshohocken, PA, 2011, www.astm.org
Back to Top