Products and Services / Standards & Publications / Standards Products


    If you are an ASTM Compass Subscriber and this document is part of your subscription, you can access it for free at ASTM Compass
    ASTM F1973 - 13(2018)

    Standard Specification for Factory Assembled Anodeless Risers and Transition Fittings in Polyethylene (PE) and Polyamide 11 (PA11) and Polyamide 12 (PA12) Fuel Gas Distribution Systems

    Active Standard ASTM F1973 | Developed by Subcommittee: F17.60

    Book of Standards Volume: 08.04

      Format Pages Price  
    PDF 6 $54.00   ADD TO CART
    Hardcopy (shipping and handling) 6 $54.00   ADD TO CART

    Reprints and Permissions

    Permissions to reprint documents can be acquired through
    Copyright Clearance Center   Visit Copyright Clearance Center  

    Reprints and Permissions

    Permissions to reprint documents can be acquired through
    Copyright Clearance Center  

    Visit Copyright Clearance Center  

    Reprints and Permissions

    Permissions to reprint documents can be acquired through
    Copyright Clearance Center  

    Visit Copyright Clearance Center  

    Historical Version(s) - view previous versions of standard

    Work Item(s) - proposed revisions of this standard

    ASTM License Agreement

    Shipping & Handling

    More F17.60 Standards Related Products Standard References

    Abstract

    This specification covers requirements and test methods for the qualification of factory assembled anodeless risers and transition fittings, for use in polyethylene (PE), in sizes through NPS 8, and Polyamide 11 (PA11), in sizes through NPS 6, gas distribution systems. The bend radius, steel pipe thread, steel flanges, and gas pressure containing factory welding shall meet the requirements prescribed. Temperature cycling test, tensile pull test, leak test, and constant tensile load joint test shall be performed to meet the requirements prescribed.

    This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.

    1. Scope

    1.1 This specification covers requirements and test methods for the qualification of factory assembled anodeless risers and transition fittings, for use in polyethylene (PE), in sizes through NPS 8, and Polyamide 11 (PA11) and Polyamide 12 (PA12), in sizes through NPS 6, gas distribution systems.

    1.2 The test methods described are not intended to be routine quality control tests.

    1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

    1.4 Throughout this specification footnotes are provided for informational purposes and shall not be considered as requirements of this specification.

    1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.


    2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    ASTM Standards

    A53/A53M Specification for Pipe, Steel, Black and Hot-Dipped, Zinc-Coated, Welded and Seamless

    A513 Specification for Electric-Resistance-Welded Carbon and Alloy Steel Mechanical Tubing

    D638 Test Method for Tensile Properties of Plastics

    D1600 Terminology for Abbreviated Terms Relating to Plastics

    D2513

    E515 Practice for Leaks Using Bubble Emission Techniques

    F412 Terminology Relating to Plastic Piping Systems

    F1588 Test Method for Constant Tensile Load Joint Test (CTLJT)

    F2785 Specification for Polyamide 12 Gas Pressure Pipe, Tubing, and Fittings

    F2897 Specification for Tracking and Traceability Encoding System of Natural Gas Distribution Components (Pipe, Tubing, Fittings, Valves, and Appurtenances)

    F2945 Specification for Polyamide 11 Gas Pressure Pipe, Tubing, and Fittings

    ANSI Standards

    ANSI B 31.8 Gas Transmission and Distribution Piping Systems Available from American National Standards Institute (ANSI), 25 W. 43rd St., 4th Floor, New York, NY 10036, http://www.ansi.org.

    UL Standard

    UL 360

    PPI Standard

    PPI TR-4 PPI Listing of Hydrostatic Design Bases (HDB), Pressure Design Bases (PDB) and Minimum Required Strength (MRS) Ratings for Thermoplastic Piping Materials or Pipe

    API Standard

    API 1104 Standard for Welding Pipelines and Related Facilities

    ASME Standard

    ASME Boiler and Pressure Vessel Code

    ICS Code

    ICS Number Code 75.200 (Petroleum products and natural gas handling equipment)

    UNSPSC Code

    UNSPSC Code 40170000(Pipe piping and pipe fittings)

    Referencing This Standard
    Link Here
    Link to Active (This link will always route to the current Active version of the standard.)

    DOI: 10.1520/F1973-13R18

    Citation Format

    ASTM F1973-13(2018), Standard Specification for Factory Assembled Anodeless Risers and Transition Fittings in Polyethylene (PE) and Polyamide 11 (PA11) and Polyamide 12 (PA12) Fuel Gas Distribution Systems, ASTM International, West Conshohocken, PA, 2018, www.astm.org

    Back to Top