| Format | Pages | Price |   |
![]() |
6 | $52.00 | ![]() |
|
![]() |
Hardcopy (shipping and handling) | 6 | $52.00 | ![]() |
![]() |
Standard + Redline PDF Bundle ![]() |
12 | $62.00 | ![]() |
Historical Version(s) - view previous versions of standard
Work Item(s) - proposed revisions of this standard
More F17.10 Standards Related Products Standard References
Abstract
This specification covers polyamide (PA) butt fusion fittings for use with polyamide pipe (IPS and ISO) and tubing (CTS). This specification covers butt fusion fittings intended for use with polyamide pipe and tubing. Fittings covered by this specification are normally molded. Fittings may be machined from extruded or molded stock. Conditioning, dimensions and tolerances, short-term rupture strength, sustained pressure test, and minimum hydrostatic burst pressure test shall be performed to conform with the requirements specified.
This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.
1. Scope
1.1 This specification covers polyamide (PA) butt fusion fittings for use with polyamide pipe (IPS and Metric) and tubing (CTS). Included are requirements for materials, workmanship, dimensions, marking, sustained pressure, and burst pressure.
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.
ASTM Standards
D1598 Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure
D1599 Test Method for Resistance to Short-Time Hydraulic Pressure of Plastic Pipe, Tubing, and Fittings
D1600 Terminology for Abbreviated Terms Relating to Plastics
D2122 Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
D4066 Classification System for Nylon Injection and Extrusion Materials (PA)
D6779 Classification System for and Basis of Specification for Polyamide Molding and Extrusion Materials (PA)
F412 Terminology Relating to Plastic Piping Systems
F2785 Specification for Polyamide 12 Gas Pressure Pipe, Tubing, and Fittings
F2945 Specification for Polyamide 11 Gas Pressure Pipe, Tubing, and Fittings
Federal Standard
CFR Title 49 Part 192 Fed. Std. No. 123 Marking for Shipment (Civil Agencies)National Sanitation Foundation Standard
Military Standard
MIL-STD-129 Marking for Shipment and StorageICS Code
ICS Number Code 23.040.45 (Plastic fittings)
UNSPSC Code
UNSPSC Code 40183000(Rubber and plastic tubing); 13111031(Polyamide)
Link Here | |||
Link to Active (This link will always route to the current Active version of the standard.) | |||
DOI: 10.1520/F1733-20
Citation Format
ASTM F1733-20, Standard Specification for Butt Heat Fusion Polyamide(PA) Plastic Fitting for Polyamide(PA) Plastic Pipe and Tubing, ASTM International, West Conshohocken, PA, 2020, www.astm.org
Back to Top